HP 2103R-CSDI manual Installing, ONline Edge, Router Module, ONline hub, If you are installing

Page 36

2-12 CHAPTER 2: INSTALLING THE EDGE ROUTER MODULE

Installing the

This section describes how to install the ONline Edge Router module in an

ONline Edge

ONline hub.

Router Module

If you are installing:

 

■An ONcore Edge Router module, refer to Installing the ONcore Edge Router Module on page 2-13.

■An ONline Edge Router module in an ONcore hub, refer to the ONcore Switching Hub Installation and Operation Guide (Document Number 17-00362)

You do not need to power off the ONline hub to install or remove the Edge Router module. You can insert the module while the hub is operating (this is called a hot swap).

To install the Edge Router module in an ONline hub:

1Use one of the following proper grounding techniques when you install the Edge Router module:

■Properly ground yourself prior to handling the module.

■Attach a static wrist guard to yourself or touch a grounded static mat prior to handling the module.

2Locate an open slot in the ONline hub. If necessary, remove a blank panel on the hub to expose a slot.

3Insert the module into the slot’s board guides and slide it into the hub by pressing firmly at the top and bottom of the faceplate. Make sure the connectors are well-seated into the backplane of the hub.

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Edge Router Module Installation Guide For Ethernet 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Configuring the Edge Router Module Monitoring Edge Router Module Operation Index Limited Warranty How to Use This Guide About this GuideIntroduction AudienceConventions List conventions used throughout this guideCommands Related Documents3Com Documents Cisco DocumentsInternational and Hughes LAN Systems, May Page Introduction LAN Product Overview Shows the architecture of each Edge Router module type Module Features Edge RouterIncluding IP/IPX Edge Router Module Features Ethernet LAN Edge Router Module Memory Configurations Feature Set Desktop Memory Type Page Installing the Edge Router Module Installation FlowchartConfigure the Edge Router module Precautionary ProceduresQuick Installation Router moduleCisco Systems Getting Started Guide Quick Installation Edge Router Module Installation Guide for Ethernet UnpackingVerifying Jumper Plug PositionsConfiguring DIP SwitchesConfiguring ONcore Carrier DIP Parameters SwitchesIsolating the ONline Edge Router Module Shows the ONcore carrier DIP switch location Enabling or Disabling Nvram ConfigurationIf the NV SEL DIP switch is To select a network Set the switches according to TableInstalling If you are installingONline Edge Router ModuleTo install the Edge Router module in an ONcore hub ONcore EdgeThis is called a hot swap Installing the Edge Router Module in an ONcore Hub Close the ejectors Figure Opened and Closed Module EjectorsPage Router Module Configuration ManagedOverview Attaching a ManagementTerminal Selecting a Network Saving the Configuration HubConfiguring Carrier in aManaged ONcore This section contains the following topicsCarrier Default Settings Configuring the Carrier in a Managed ONcore Hub DMM DIP Nvram DIP Terminal to Auxiliary port Console Port Attaching a Terminal Cable to the Console Port Mini-DIN connector pinouts are provided in Appendix a Page Module Operation Monitoring EdgeOperation Edge Router Module LEDs Following network management module commands Showing ModuleStatus Each LED is described in TableUsing the Show Module Command Syntax for the Show Module command isONline show module 6 verbose Port Command Ports Syntax for the Show Port command is Edge Router module installed in slot 1 of an ONcore hubONcore show port Page Troubleshooting Troubleshooting Troubleshooting Network Connectivity Problems Problems Correcting OperatingMalfunctions MalfunctionsSeconds, and then power it on Specifications General Specifications ElectricalEnvironmental Specifications Mechanical Specifications5006C-FT Cables when you install all equipment Cable PinoutsOpenHub Management Cable Part Number OHPMGT-CAB OpenHub Management Cable has aDTR CTS TXD CTS Cable Pinouts DTE DCE Ltst CS+ SCTE+ Table A-17 X.21 DTE and DCE Cable Pinouts DB-15 15 Pin Services Online TechnicalThrough the following online systems Days a week, 24 hours a dayAccess by Digital Modem 408Press Return to view the 3ComForum main menu Support From Your NetworkSupplier U.S. and Canada, call 800 876-3266 for customer service To find your authorized service provider3Com CorporationAccessing the 3Com ISD MIB To exit the FTP session, invoke the quit commandContacting 3Com ISD Technical Publications Index NumericsQuick Software 1-8Upgrading Firmware 1-8 memory Page Limited Warranty 408 764-5000 3/18/96
Top Page Image Contents