HP E1368A manual Reset Conditions

Page 30

Reset Conditions

When the Microwave Switch is switched on or *RST (reset), all channels are set to open (refer to Figure 2-6), and the current channel list for scanning is invalidated. Table 3-2 lists the parameters and default values for the functions described in Chapter 3.

Table 3-2. *RST (Reset) Default Conditions and Values

	Parameter	Default	Description


ARM:COUNt		1	Number of scanning cycles is one.
TRIGger:SOURce		IMM	Will advance scanning cycles automatically.
INITiate:CONTinuous		OFF	Number of scanning cycles is determined by
			ARM:COUNt.
OUTPut:STATe		OFF	"Trig Out" port on mainframe is disabled.
SCAN:MODE		NONE	Not used by the Microwave Switch modules.
SCAN:PORT		NONE	Not used by the Microwave Switch modules.

Caution When the Microwave Switch is powered up, signals connected to the normally closed (N/C) port will also be connected to the output port (refer to Figure 2-6).

Note The Microwave Switch modules do not support 4-wire resistance scanning (FRES).

30 Using the HP E1368A/69A/70A Modules

Chapter 3

Image 30

Contents Contents Open OPEN? Scan Scanmode SCANMODE? Cpon HP E1368A/69A/70A Modules User’s Manual Contents Certification Documentation History April According to ISO/IEC Guide 22 and ENPage Business Reply Mail Page Using This Chapter Microwave Switch DescriptionGetting Started with the HP E1368A/69A/70A Chapter Power Supply Circuit HP E1368A SwitchesProgramming the Microwave Switch Instrument DefinitionCard Numbers for Multiple-Module Switchboxes Example Reset the switchbox and close channel Initial OperationConfiguring the HP E1368A/69A/70A Modules Setting the Address Switch Logical Address SelectionSelecting the Interrupt Priority Interrupt Priority SelectionInstalling Switches on the HP E1369A Installing Switches on the ModuleChapter Configuring the HP E1368A/69A/70A Modules Microwave Switch Installation Connecting Switches External To the Module Selecting Switch Power Connecting Field Wiring Selecting Switch VoltageInstalling a Switch Or Attenuator on Module Microwave Switch/Attenuator Installation Shows the internal schematic of a single attenuator section Using the HP E1368A/69A/70A Modules Microwave Switch CommandsReset Conditions Switching Channels Example Single Channel SwitchingPower To connect C to Port 1, execute 33363K 33364K 33365K 33366K Example Multiple Channel Switching Using EXTernal Example Transfer Switch Using Two Port Switches Example Transfer Switch Using One Port Switch To route signal B to the output, execute Example 4 x 1 MultiplexerScanning Channels Selects the Trigger SourceExample Scanning Channels Output 722TRIG EXT …Example Using the Scan Complete Bit Example Multiple Channel Scanning110END Detecting Error Conditions Recalling and Saving StatesRepeat Synchronizing the Microwave Switch Synchronizing InstrumentsQuerying the Microwave Switch Command Types Common Command FormatScpi Command Format HP E1368A/69A/70A Command Reference Chapter Semicolon between the commands. For example Scpi Command Reference ABORtExample Stopping a Scan with ABORt For the number of scanning cycles default is ∙ Number of Scans Use only numeric values between 1Armcoun MONitorCARD Example Select Module #2 in a Switchbox for MonitoringDISPlay ∙ Selecting a Specific Module to be Monitored UseExample Enabling the Monitor Mode Example Querying the Monitor Mode∙ Selecting the Module to be Monitored Use ∙ Stopping Continuous Scans See the ABORt command INITiateExample Enabling Continuous Scans Example Query Continuous Scanning State Example Query Trig Out Port Enable State OUTPutExample Enabling Trig Out Port Example Closing Microwave Switch Channels ROUTe∙ Closing Channels To close Example Opening Microwave Switch Channels ∙ Opening Channels To openExample Scanning Using External Device Or any combinationChapter HP E1368A/69A/70A Command Reference STATus ∙ Setting Bit 7 of the Status Byte Register Example Query the Standard Operation Status Enable RegisterSTATOPER? SYSTem CDEScription?Comments Microwave Switch Module Model Number Example Reading the Error QueueExample Reading the Model Number of a Card #1 Module TRIGger ∙ Executing the TRIGgerIMMediate Command a channel listExample Advancing Scan Using the TRIGger Command ∙ Hold or BUS Source Remains If selected, the TRIGgerSOURce∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Scanning Using External TriggersScanning Using Bus Triggers Example Query the Trigger SourceIeee 488.2 Common Commands HP Command Module User’s Manual, or the ANSI/IEEE StandardCommand Quick Reference Scpi Commands for Quick ReferenceHP E1368A/69A/70A Command Reference Chapter Connectors Used P1 No. Slots Characteristic Impedence 50Ω Insertion LossMaximum Input Power 1 Watt average Operating TemperatureHP E1368A/69A/70A Specifications Appendix a HP E1368A/69A/70A Registers Register DefinitionsAddressing the Registers Reading the RegistersID and Device Type Registers Status/Control Register Channel Enable Register Writing to the RegistersHP E1368A/69A/70A Registers Appendix B HP E1368A/69A/70A Error Messages Page Index HP E1368A/69A/70A Modules User’s Manual IndexHP E1368A/69A/70A Modules User’s Manual Index HP-IB HP E1368A/69A/70A Modules User’s Manual Index HP E1368A/69A/70A Modules User’s Manual Index HP E1368A/69A/70A Modules User’s Manual Index