Home Automation OmniPro II Controlling RadioRA Units, Controlling ALC or X-10Units, Page

Page 31

¾Press 4 (LVL) to set the desired lighting level of the selected unit (0%-100%).

¾5 (RMP) does not affect CentraLite units.

¾Press 9 (TIM) to time the selected unit (On or Off). Timed commands may be from 1-99 seconds, 1-99 minutes or 1-18 hours.

¾Press # (STA) to see the status (On or Off) of a CentraLite device.

Controlling RadioRA Units

Entry Lights

0=OFF 1=ON 2=DIM 3=BRT ↓

Entry Lights

4=LVL 5=RMP 9=TIM #=STA↑

¾Press 0 (OFF) to turn the selected unit off

¾Press 1 (ON) to turn the selected unit on.

¾2 (DIM) does not affect RadioRA units.

¾3 (BRT) does not affect RadioRA units.

¾Press 4 (LVL) to set the desired lighting level of the selected unit (0%-100%).

¾5 (RMP) does not affect RadioRA units.

¾Press 9 (TIM) to time the selected unit (On or Off). Timed commands may be from 1-99 seconds, 1-99 minutes or 1-18 hours.

¾Press # (STA) to see the status (On or Off) of a RadioRA device.

Note: When a RadioRA device transmits a signal (i.e. Switch or Dimmer is turned on or off locally, Mater Control button is pressed, or Phantom Button is executed), OmniPro II will automatically update the status of each affected device.

Controlling ALC or X-10 Units

Entry Lights

0=OFF 1=ON 2=DIM 3=BRT ↓

Entry Lights

4=LVL 5=RMP 9=TIM #=STA↑

¾Press 0 (OFF) to turn the selected unit off.

¾Press 1 (ON) to turn the selected unit on.

¾Press 2 (DIM) to dim the selected unit (1-9 steps, each step is 10% from its current level).

¾Press 3 (BRT) to brighten the selected unit (1-9 steps, each step is 10% from its current level).

¾Press 4 (LVL) to set the desired lighting level of the selected unit (0%-100%).

¾Press 5 (RMP) to ramp the lighting level of an ALC Dimmer Switch to a new level at a selectable ramp rate.

• 5 (RMP) does not affect X-10 units.

¾Press 9 (TIM) to time the selected unit (On or Off). Timed commands may be from 1-99 seconds, 1-99 minutes or 1-18 hours.

¾Press # (STA) to view the current status of the unit.

Page 23

Image 31

Contents Control & Security System HOME AUTOMATION, INCDocument Number 20R00-2Rev. January All Rights Reserved Copyright 2001-2006Home Automation, IncContents INTRODUCTIONOVERALL DESCRIPTION SECURITY SYSTEM OPERATIONCONTROL TELEPHONE CONTROL SETUP APPENDIX A - DIAL OUT PLANNER UNDERWRITERS LABORATORIES REQUIREMENTSFEDERAL COMMUNICATION COMMISSION NOTICE CANADIAN INDUSTRY CANADA NOTICEPage Underwriters Laboratories UL Listing INTRODUCTIONPage 2- DAY OVERALL DESCRIPTIONConsole Operation 1- OFF7- CONSOLE LED Normal Top-LevelDisplayDisplay Menus 6- UP ARROWTo silence the beeper, press the * key Error BeepsMain Menu Trouble BeepsConfirmation Beep OmniPro II MaintenanceCancel Areas1 = DAY SECURITY SYSTEM OPERATIONArming the Security System 0 = OFF4 = VACATION Using Shortcut Keys2 = NIGHT 3 = AWAYRestoring Zones 9 = RESTOREQuick Arm Bypassing Zones#=GOTO What To Do When You Come HomeWhat Happens When the Alarm is Activated Burglar Alarm ActivatedPage Fire Alarm ActivatedGas Alarm Activated Emergency KeysPolice Emergency Duress Code Entered or Duress Alarm ActivatedAlarm Reset Alarm CancelPage Trouble IndicationsCodes Master CodeManager Code Panic SwitchesDuress Code Area ArmingPage GOTO AreaPage Testing Your SystemPage Control CommandsCONTROL About UPBAbout Rooms When set to UPB, the OmniPro II controller canRoom Controller LED Indicators HAI Lighting Control HLC FormatPage About CentraLiteAbout Lutron RadioRA About House ControllersALC Module Types About ALCAbout House CodesPage Unit NumbersOmniPro II Unit Numbers Module / Output Unit NumbersControlling a Room of HLC Lighting Configuring Lighting Scenes in an HLC RoomScrolling Through Names Controlling UnitsPage StepOperation Controlling CentraLite UnitsControlling ALC or X-10Units Controlling RadioRA UnitsPage Page Ramp Command ALCScene Command Compose Controlling Compose UnitsPage Timed CommandsStatus of a Unit Internal FlagsAll Off Controlling OutputsAll On / Off All Lights OnLeviton Scene Control Scene CommandsScene Set Command Scene On CommandActivating and Deactivating Links Scene Off CommandSetting a Link Lighting Scenes UPB LinksPHANTOM BUTTON 1 0=OFF 1=ON Executing Phantom ButtonsExecuting CentraLite Scenes ENTER BUTTONDinner for Two Button ButtonsTemperature Control Leave for Work ButtonPage HAI RC-SeriesThermostatsPage Programmable Energy Saver Modules PESMsPage The following control actions are allowed on PESMsPage Freeze AlarmsIMPORTANT NOTES Indoor and Outdoor TemperatureTemperature Control of Appliances Temperature AlarmsHumidity Outdoor TemperaturePage Configuring HLC DevicesConfiguring HLC Devices using an Omni Console StatusStep Operation Setup Mode for HLC DevicesStep Operation Step OperationDEAD - DEAD PHONE LINE ONHK - ON HOOKOFFHK - OFF HOOK RING - RINGINGPage THROUGHShow Events Event LogPage Clear Text Messages MessagesRecord Memo Message Play Memo MessageSay Message Show MessageLog Message Clear MessageENTER MESSAGE Send Message Pro-LinkSERIAL PORT MSGNAMERemote Phones TELEPHONE CONTROLTelephone Interface In-HousePhonesPage Phone Access Denied - Remote LockoutAlternate Method Main Menu4 - All 1 - Control2 - Security 3 - Button7 - Events When an HAI Communicating Thermostat is enteredWhen a Programmable Energy Saver PESM is entered 6 - StatusPaging and Listening When the HAI Two-WayAudio Module is being used8 - Message Playing and Recording a MessagePage 9 - Good-ByePanic Button over the Phone # # # # # # Playing and Recording the AddressHow the OmniPro II Voice Dialer Works Emergency Dial-OutDigital Dialer Voice DialerPage PC AccessWhat You Hear - If Your OmniPro II Calls You Entering the CodePage Connecting to Network via PC AccessBuilt-InEthernet Port OmniPro II Ethernet ConnectionsDynamic DNS Local NetworkPage Page Local / Wide Area Networki.e i.eAuthority Level SETUPSet Up Codes Access AreasPage Set Up TimeDuress Code TIMEPage Advanced Control Programming ACP1 = Add Programs 2 = Show ProgramsPage Menu3 = Delete All Programs Edit ProgramsPage Times Programs Edit Programs WhenPage Button and Event Programs Control Unit / Switch Press Event ButtonsPage UPB 6-ButtonKeypad Corresponding Switch TableSwitch OmniProPage Zone Event ButtonsAll On/Off Event Buttons UPB Link Event ButtonsPage Alarm Event ButtonsX-10Event Buttons Miscellaneous Event ButtonsMessage Event Buttons Pro-Link Switch Press Event Buttons CentraLitePage Program Control Commands Edit Program CommandPage Program All On / All Off Commands Unit Toggle CommandProgram Security Commands Program Button CommandsProgram Energy Cost Program Video CommandsProgram Message Commands Program Temperature CommandsProgram Zone Conditions Edit Program ConditionProgram Control Conditions Program Security Mode ConditionsProgram Other Conditions Program Time Clock ConditionsPage Answer Outside Call Set Up DialTelephone Access Remote CommandsPage Dial Out NumberDial Out Numbers Dial OrderAudible Exit Delay Set Up ArmingEntry Delay Exit DelayAll On For Alarm Set up MiscellaneousEnable Quick Arm Enable Auto BypassFORMAT Enable Freeze AlarmFlash For Alarm House Codes 1-16FormatTime Clocks House Codes 1-16All OnPage Page Latitude, Longitude, and Time ZoneZONE NAME Daylight SavingsDESCRIPTION Controller IP AddressController Port Number NUMBEREncryption Key Set Up NamesPage 4=CODE 5=TEMP 6=AREA 8=MSG↑ Set Up VoiceSet Up Address SET UP VOICE 1=CTRL 2=ZONE 3=BTTN ↓FIRE ESCAPE PLANNING UNDERWRITERS LABORATORIES REQUIREMENTSPage Page FEDERAL COMMUNICATION COMMISSION NOTICEIF YOU HAVE TROUBLE WITH YOUR PHONES CANADIAN INDUSTRY CANADA NOTICEPage OmniPro II Voice Dial-OutPlanner APPENDIX A - DIAL OUT PLANNERPage Page INSTRUCTIONS TO CALLED PARTYCODE CHAR APPENDIX B - TEXT DESCRIPTION CHARACTER CODESCODE CHAR CODE CHARCODE APPENDIX C - VOICE DESCRIPTION CODESCODE DESCRIPTIONDESCRIPTION CODEDESCRIPTION CODEDESCRIPTION CODEDESCRIPTION CODECODE NOTES ON CUSTOM PHRASESCODE DESCRIPTIONPage HAI New Orleans, LA U S A NOTE TO INSTALLER