Home Automation OmniPro II Ramp Command ALC, Controlling Compose Units, Scene Command Compose

Page 32

Ramp Command (ALC)

When ALC Switch Modules are being used, it is possible to ramp the lighting level of an ALC Dimmer Switch to a new level at a selectable ramp rate. Only ALC Dimmer Switches respond to the Ramp command.

Press the 5 (RAMP) key to select the ramp command. The keypad will then prompt you for the desired ramp rate:

ENTER RATE:

MINUTES (1-99) #=H/M/S

The rate specifies the time it takes the switch to go from full off to full on, or from full on to full off. Thus a level change from full off to 50% on will take half the time specified.

Before any digits are entered, the ' # ' key may be used to switch between specifying the rate in minutes, seconds, and hours. After you choose between minutes, seconds, and hours, enter the rate (2-99 seconds, 1-99 minutes, or 1-10 hours).

Next, enter a number (0-100) to indicate the final lighting level (intensity) desired.

LIGHTING LEVEL:

0-100%:

The keypad will beep and the lighting level will be adjusted. The keypad display top line will read:

Entry Lights 40% AT 1H

Controlling Compose Units

Entry Lights

0=OFF 1=ON 2=DIM 3=BRT ↓

Entry

Lights

#=STA↑

4=SCN

9=TIM

¾Press 0 (OFF) to turn the selected unit off.

¾Press 1 (ON) to turn the selected unit on.

¾Press 2 (DIM) to dim the selected unit (1-9 steps, each step is 10% from its current level).

¾Press 3 (BRT) to brighten the selected unit (1-9 steps, each step is 10% from its current level).

¾Press 4 (SCN) to set a group of lights to their predefined lighting levels.

¾Press 9 (TIM) to time the selected unit (On or Off). Timed commands may be from 1-99 seconds, 1-99 minutes or 1-18 hours.

¾Press # (STA) to view the current status of the unit.

Scene Command (Compose)

If Compose lighting switches are part of your installation, the Scene (SCN) command is used to set a group of lights to predefined lighting levels. There is an Off command, an On command, and 12 lighting scenes for each group of Compose lighting switches.

SCENE:

0=OFF 1=ON 2-13=A-L

Enter 0, followed by the ' # ' key, to turn the lights that are part of the selected group off. Enter 1, followed by the ' # ' key, to set the lights that are part of the selected group to predefined lighting levels.

To set the lights in the selected group to a predefined scene, enter the Scene number 2-13 (which corresponds to Scene A-L, respectively), followed by the ' # ' key. All lights that are part of the selected group are set to the predefined lighting levels for the selected Scene.

Page 24

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Document Number 20R00-2Rev. January HOME AUTOMATION, INCControl & Security System Copyright 2001-2006Home Automation, Inc All Rights ReservedINTRODUCTION OVERALL DESCRIPTIONSECURITY SYSTEM OPERATION ContentsCONTROL TELEPHONE CONTROL SETUP UNDERWRITERS LABORATORIES REQUIREMENTS FEDERAL COMMUNICATION COMMISSION NOTICECANADIAN INDUSTRY CANADA NOTICE APPENDIX A - DIAL OUT PLANNERPage Page INTRODUCTIONUnderwriters Laboratories UL Listing OVERALL DESCRIPTION Console Operation1- OFF 2- DAYNormal Top-LevelDisplay Display Menus6- UP ARROW 7- CONSOLE LEDError Beeps Main MenuTrouble Beeps To silence the beeper, press the * keyOmniPro II Maintenance CancelAreas Confirmation BeepSECURITY SYSTEM OPERATION Arming the Security System0 = OFF 1 = DAYUsing Shortcut Keys 2 = NIGHT3 = AWAY 4 = VACATION9 = RESTORE Quick ArmBypassing Zones Restoring ZonesWhat To Do When You Come Home What Happens When the Alarm is ActivatedBurglar Alarm Activated #=GOTOFire Alarm Activated Gas Alarm ActivatedEmergency Keys PageDuress Code Entered or Duress Alarm Activated Alarm ResetAlarm Cancel Police EmergencyTrouble Indications CodesMaster Code PagePanic Switches Duress CodeArea Arming Manager CodeGOTO Area PageTesting Your System PageControl Commands CONTROLAbout UPB PageWhen set to UPB, the OmniPro II controller can Room Controller LED IndicatorsHAI Lighting Control HLC Format About RoomsAbout CentraLite About Lutron RadioRAAbout House Controllers PageAbout ALC AboutHouse Codes ALC Module TypesUnit Numbers OmniPro II Unit NumbersModule / Output Unit Numbers PageConfiguring Lighting Scenes in an HLC Room Scrolling Through NamesControlling Units Controlling a Room of HLC LightingStep OperationControlling CentraLite Units PagePage Controlling RadioRA UnitsControlling ALC or X-10Units Ramp Command ALC Scene Command ComposeControlling Compose Units PageTimed Commands Status of a UnitInternal Flags PageControlling Outputs All On / OffAll Lights On All OffScene Commands Scene Set CommandScene On Command Leviton Scene ControlScene Off Command Setting a Link Lighting ScenesUPB Links Activating and Deactivating LinksExecuting Phantom Buttons Executing CentraLite ScenesENTER BUTTON PHANTOM BUTTON 1 0=OFF 1=ONButtons Temperature ControlLeave for Work Button Dinner for Two ButtonHAI RC-SeriesThermostats PageProgrammable Energy Saver Modules PESMs PageThe following control actions are allowed on PESMs PageFreeze Alarms IMPORTANT NOTESIndoor and Outdoor Temperature PageTemperature Alarms HumidityOutdoor Temperature Temperature Control of AppliancesConfiguring HLC Devices Configuring HLC Devices using an Omni ConsoleStatus PageSetup Mode for HLC Devices Step OperationStep Operation Step OperationONHK - ON HOOK OFFHK - OFF HOOKRING - RINGING DEAD - DEAD PHONE LINETHROUGH PagePage Event LogShow Events Messages Record Memo MessagePlay Memo Message Clear Text MessagesShow Message Log MessageClear Message Say MessageSend Message Pro-Link SERIAL PORTMSGNAME ENTER MESSAGETELEPHONE CONTROL Telephone InterfaceIn-HousePhones Remote PhonesPhone Access Denied - Remote Lockout Alternate MethodMain Menu Page1 - Control 2 - Security3 - Button 4 - AllWhen an HAI Communicating Thermostat is entered When a Programmable Energy Saver PESM is entered6 - Status 7 - EventsWhen the HAI Two-WayAudio Module is being used 8 - MessagePlaying and Recording a Message Paging and Listening9 - Good-Bye Panic Button over the Phone # # # # # #Playing and Recording the Address PageEmergency Dial-Out Digital DialerVoice Dialer How the OmniPro II Voice Dialer WorksPC Access What You Hear - If Your OmniPro II Calls YouEntering the Code PageConnecting to Network via PC Access Built-InEthernet PortOmniPro II Ethernet Connections PagePage Local NetworkDynamic DNS Local / Wide Area Network i.ei.e PageSETUP Set Up CodesAccess Areas Authority LevelSet Up Time Duress CodeTIME PageAdvanced Control Programming ACP 1 = Add Programs2 = Show Programs PageMenu PagePage Edit Programs3 = Delete All Programs Page Edit Programs WhenTimes Programs Page Control Unit / Switch Press Event ButtonsButton and Event Programs Corresponding Switch Table SwitchOmniPro UPB 6-ButtonKeypadZone Event Buttons All On/Off Event ButtonsUPB Link Event Buttons PageAlarm Event Buttons X-10Event ButtonsMiscellaneous Event Buttons PagePage Switch Press Event Buttons CentraLiteMessage Event Buttons Pro-Link Page Edit Program CommandProgram Control Commands Unit Toggle Command Program Security CommandsProgram Button Commands Program All On / All Off CommandsProgram Video Commands Program Message CommandsProgram Temperature Commands Program Energy CostEdit Program Condition Program Control ConditionsProgram Security Mode Conditions Program Zone ConditionsPage Program Time Clock ConditionsProgram Other Conditions Set Up Dial Telephone AccessRemote Commands Answer Outside CallDial Out Number Dial Out NumbersDial Order PageSet Up Arming Entry DelayExit Delay Audible Exit DelaySet up Miscellaneous Enable Quick ArmEnable Auto Bypass All On For AlarmEnable Freeze Alarm Flash For AlarmHouse Codes 1-16Format FORMATPage House Codes 1-16All OnTime Clocks Latitude, Longitude, and Time Zone ZONE NAMEDaylight Savings PageController IP Address Controller Port NumberNUMBER DESCRIPTIONPage Set Up NamesEncryption Key Set Up Voice Set Up AddressSET UP VOICE 1=CTRL 2=ZONE 3=BTTN ↓ 4=CODE 5=TEMP 6=AREA 8=MSG↑Page UNDERWRITERS LABORATORIES REQUIREMENTSFIRE ESCAPE PLANNING FEDERAL COMMUNICATION COMMISSION NOTICE PagePage CANADIAN INDUSTRY CANADA NOTICEIF YOU HAVE TROUBLE WITH YOUR PHONES Page APPENDIX A - DIAL OUT PLANNEROmniPro II Voice Dial-OutPlanner INSTRUCTIONS TO CALLED PARTY PageAPPENDIX B - TEXT DESCRIPTION CHARACTER CODES CODE CHARCODE CHAR CODE CHARAPPENDIX C - VOICE DESCRIPTION CODES CODEDESCRIPTION CODECODE DESCRIPTIONCODE DESCRIPTIONCODE DESCRIPTIONCODE DESCRIPTIONNOTES ON CUSTOM PHRASES CODEDESCRIPTION CODEPage NOTE TO INSTALLER HAI New Orleans, LA U S A
Top Page Image Contents