Samsung ASV24PSPNXEA, ASV13PSPNXEA, ASV18PSPXXEA, ASV18PUQNXEA, ASV10PUQNXEA, ASV13PUQNXEA manual Mode

Page 13

mode

For a comfortable sleep, the air conditioner will operate it Fall asleep Sound sleep Wake up from mode.

When the air conditioner is on and in cool/heat mode

1. Press the button on the remote controller.



controller display.

ENGLISH

2. Press the button to set the time.

 You can set the time in half hourly unit from 30 minutes ~ 3 hours and hour unit from 3 hours ~ 12 hours.

 Operating hour can be set from minimum 30 minutes to maximum

12 hours.

Default operation hour is set to 8 hours.

3. Press the Set/Cancelbutton to active it on.



Then the air conditioner operates in good’sleep(Cool) mode.

If you don’t press Set/Cancel button within 10 seconds after pressing the the air conditioner will return to previous status.

Check indicator on the remote controller.

Cancel Press the Set/Cancel button once again.

You can set the desired temperature by 1˚C in the range of 16˚C~30˚C.

Fan speed will be adjusted automatically according to the mode.

However, I f you select mode while heating operation is on, you can adjust fan speed.

mode.

However, if you select mode while heating operation is on,

Temperature and fan speed changes in mode

•Fallasleep: Eases you into sleep by dropping the temperature.

•Sound sleep: Relaxes your body and raises your temperature slightly.

•Wake fromup mode: Allows you to wake up from comfortable intermittent air and it makes you feel refreshed.

• Set	timer in	mode over 5 hours. You fell disturbed sleep if the	is set too short or long
because the default is set to 8-hour-operation.

•If the mode is set less than 4 hours, the operation will stop at the same time.

If the mode is set over 5 hours, it will run as Wake up stage from the last one hour before it stops.

•Recommended set temperature is between 25˚C~27˚C for cooling and 21˚C~23˚C for heating.

13

Image 13

Contents Air Conditioner Contents Important safety symbols and precautions Safety precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges Checking before useChecking the name of the parts Power buttonMain parts DisplayRemote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasic function Press Button to adjust the temperaturePress the Air swing button on the remote controller Using the Turbo functionCirculate the air Position you preferMode Press the button Press the button to set the time Press the Set/Cancel button to active it onTimer 1 hour Using the Smart Saver functionTimer 5 hours From the moment you have set the timerUsing the Quiet function Cleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchangerClean the Air Cleaning the air conditionerSlide it down Dry the Ai lter in a ventilated areaPeriodical checks Maintaining the air conditionerTroubleshooting If may not be a Outdoor unit Heat exchanger during Heat mode in winterConnection Model Name Included Models Remark General informationInstalling the unit Choosing the installation locationPower supply line, fuse or circuit breaker Won’t be considered in-warranty and charged to end userModel Outdoor Unit When the air outlet is towards the wall When installing more than 1 outdoor unitTop view Side view Accessories in the indoor unit case AccessoriesAccessories in the outdoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the cable Connecting the assembly cableFix the indoor unit Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryThen pull it out through the appropriate hole Smooth the cut edgesCutting or extending the pipe Purging the indoor unitUnscrew the caps at the end of each pipe Connect the pipesCracked Correct InclinedApplying the following torque Outer DiameterChanging direction of the drain hose Drain hose installationExcessive torque can be cause of gas leakage Purging the connected pipesAdding Refrigerant Covered by the Kyoto Protocol 1975To check for gas leaks on the outdoor unit Performing the gas leak testsTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesFixing the outdoor unit in place Outdoor unit installed on the wall by rackPart without insulation on the end of the pipes Properly ModelPress the Power button and check the following Pump down procedure when removing the productPress the Mode button to select Cool or Heat mode Final Check and Trial OperationHow to connect your extended power cables Questions or COMMENTS?