Samsung ASV18PSPXXEA, ASV13PSPNXEA Changing direction of the drain hose, Drain hose installation

Page 33

Drain hose installation

1.If necessary, connect the 2-meter extension drain hose to the drain hose.

2.If you use the extension drain hose, insulate the inside of the extension drain hose with a shield.

3. tightly with a clamp.

• If you do not use the other drain hose hole, block it with a rubber stopper.

	4.	Pass the drain hose under the refrigerant pipe, keeping the drain hose	Shield
		tight.
	5.	Pass the drain hose through the hole in the wall. Check if it slants
	5.		Drain hose
		downwards as seen in the picture.	Drain hose
		downwards as seen in the picture.

Drain hose hole

Extension drain hose

ENGLISH

• The hose will be	permanently into position after	the installation and the gas leak test; refer to page
38 for further details.

•Make sure the installed direction of the drain hose is correct. Inadequate installation may cause condensate water leakage.

•If the drain hose is routed inside the room, insulate the hose so that dripping condensation does not damage the

•DO NOT WALL UP THE DRAIN HOSE CONNECTION !

Drain hose connection must be easy accessible and serviceable.

Changing direction of the drain hose

Change the direction only when it is necessary.

	1.	Detach the rubber cap with the plier.	Screw hole
	1.	Detach the rubber cap with the plier.	Screw
	2.	Detach the drain hose by pulling it and turning to the left.	Screw
	2.
	3.	hose and the outlet of the drain pan.	Drain hose
		hose and the outlet of the drain pan.
	4.	Attach the rubber cap with a screwdriver by turning it to the right until it	Drain pan outlet
			Drain pan outlet

5. Check for leakage on both side of the drain outlet.	Rubber cap

Pour the water in direction of arrow.

Direction of the drained water

• Make sure the indoor unit is in upright position when you pour water to check for leakage.

33

Image 33

Contents Air Conditioner Contents Important safety symbols and precautions Safety precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges Checking before useChecking the name of the parts Power buttonMain parts DisplayRemote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasic function Press Button to adjust the temperaturePress the Air swing button on the remote controller Using the Turbo functionCirculate the air Position you preferMode Press the button Press the button to set the time Press the Set/Cancel button to active it onTimer 1 hour Using the Smart Saver functionTimer 5 hours From the moment you have set the timerUsing the Quiet function Cleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchangerClean the Air Cleaning the air conditionerSlide it down Dry the Ai lter in a ventilated areaPeriodical checks Maintaining the air conditionerTroubleshooting Outdoor unit Heat exchanger during Heat mode in winter If may not be aConnection Model Name Included Models Remark General informationInstalling the unit Choosing the installation locationPower supply line, fuse or circuit breaker Won’t be considered in-warranty and charged to end userModel Outdoor UnitWhen installing more than 1 outdoor unit  When the air outlet is towards the wallTop view Side view Accessories Accessories in the indoor unit caseAccessories in the outdoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the assembly cable Connecting the cableFix the indoor unit Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryThen pull it out through the appropriate hole Smooth the cut edgesCutting or extending the pipe Purging the indoor unitUnscrew the caps at the end of each pipe Connect the pipesCracked Correct InclinedApplying the following torque Outer DiameterChanging direction of the drain hose Drain hose installationExcessive torque can be cause of gas leakage Purging the connected pipesAdding Refrigerant Covered by the Kyoto Protocol 1975To check for gas leaks on the outdoor unit Performing the gas leak testsTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesFixing the outdoor unit in place Outdoor unit installed on the wall by rackPart without insulation on the end of the pipes Properly ModelPress the Power button and check the following Pump down procedure when removing the productPress the Mode button to select Cool or Heat mode Final Check and Trial OperationHow to connect your extended power cables Questions or COMMENTS?