Samsung ASV18PUQXXEA Fixing the outdoor unit in place, Outdoor unit installed on the wall by rack

Page 38

Fixing the indoor unit in place

Perform the following work on the area where gas leak test was done priorly.

After checking for gas leaks in the system, insulate the pipe, hose and cables. Then place the indoor unit on the installation plate.

1.

part without insulation on the end of the pipes.

2.Wind the pipe, assembly cable and drain hose with vinyl tape.

3.Place the bundle (the pipe, assembly cable and drain hose) in the lower part of the indoor unit carefully so it does not project from the rear of the indoor unit.

4.Hook the indoor unit to the installation plate and move the unit to the right and left until it is securely in place.

•Make sure pipe does not move when you install the indoor unit on

an installation plate.

5.Wrap the rest of the pipe with vinyl tape.

6.Attach the pipe to the wall using clamps (optional).

Insulation

Pipes

 

Installation

 

plate

Connecting

Vinyl tape

pipes

Connecting wires

 

Drain hose

 

Fixing the outdoor unit in place

Install the outdoor unit in level on a stable base to avoid the generation of noise and vibration, especially when installing the unit close to a neighbor.

appropriate support (wall or ground).

'X' mm

'Y' mm

1.

Place the outdoor unit as indicated on the top of the unit to let the discharged air out

 

 

 

 

Rubber leg

 

 

 

 

 

 

 

 

 

properly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Model

X

Y

2.

Fix the outdoor unit in level to an appropriate support using anchor bolts.

 

10/13

538

290

3.

If the outdoor unit is exposed to strong winds, install shield plates around the outdoor

 

 

 

18

543

319

 

 

 

24

660

340

 

unit so that the fan can operate correctly.

 

 

 

• Secure the rubber leg to prevent the generation of noise and vibration.

Outdoor unit installed on the wall by rack

Designed to cut o residual vibration

from outdoor unit to rack.

 

 

(not supplied with product)

• Ensure the wall will be able to suspend the weight of rack and outdoor unit;

•Install the rack close to the column as much as possible;

• Install proper grommet in order to reduce noise and residual vibration transferred by outdoor unit towards wall.

Soft rubber designed to cut vibration from rack to wall. (not supplied with product)

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Air Conditioner Contents Follow directions Safety precautionsImportant safety symbols and precautions Wall socketFor Using For Cleaning Checking before use Operation rangesMain parts Power buttonChecking the name of the parts DisplayChecking the remote controller Remote controller buttonsStoring the remote controller Remote controller displayBattery changing time Inserting the batteriesBasic function Button to adjust the temperature PressCirculate the air Using the Turbo functionPress the Air swing button on the remote controller Position you preferMode Press the Set/Cancel button to active it on Press the button Press the button to set the timeTimer 5 hours Using the Smart Saver functionTimer 1 hour From the moment you have set the timerUsing the Quiet function Opening the panel Cleaning the indoor unitCleaning the outdoor unit heat exchanger Heat exchangerSlide it down Cleaning the air conditionerClean the Air Dry the Ai lter in a ventilated areaMaintaining the air conditioner Periodical checksTroubleshooting Connection Outdoor unit Heat exchanger during Heat mode in winterIf may not be a General information Model Name Included Models RemarkPower supply line, fuse or circuit breaker Choosing the installation locationInstalling the unit Won’t be considered in-warranty and charged to end userOutdoor Unit ModelTop view Side view When installing more than 1 outdoor unit When the air outlet is towards the wall Accessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Tools required for installation General Tools Fixing the installation plateOptional accessories Tools for test operationsFix the indoor unit Connecting the assembly cableConnecting the cable Extend the assembly cable if necessary Each wire is labeled with the corresponding terminal numberSmooth the cut edges Then pull it out through the appropriate holeUnscrew the caps at the end of each pipe Purging the indoor unitCutting or extending the pipe Connect the pipesApplying the following torque Correct InclinedCracked Outer DiameterDrain hose installation Changing direction of the drain hosePurging the connected pipes Excessive torque can be cause of gas leakageAdding Refrigerant 1975 Covered by the Kyoto ProtocolTo check for gas leaks on the indoor unit Performing the gas leak testsTo check for gas leaks on the outdoor unit Leak test with nitrogen before opening valvesPart without insulation on the end of the pipes Outdoor unit installed on the wall by rackFixing the outdoor unit in place Properly ModelPress the Mode button to select Cool or Heat mode Pump down procedure when removing the productPress the Power button and check the following Final Check and Trial OperationHow to connect your extended power cables Questions or COMMENTS?
Top Page Image Contents