Samsung ASV10PSPXXEA Remote controller display, Battery changing time, Inserting the batteries

Page 9

Remote controller display

	Turbo indicator		Operation mode
	Turbo indicator		indicator
	SPi indicator		indicator
	SPi indicator	Cool	Low battery indicator
	Quiet indicator	Cool	Low battery indicator
	Quiet indicator		Transmit indicator
	Smart Saver indicator		Transmit indicator
	Smart Saver indicator		Air swing indicator
	Use 2 nd function		Air swing indicator
	Use 2 nd function		Fan speed indicator
	indicator		Fan speed indicator
	indicator		Auto (Turbo)
	On Timer indicator		Auto (Turbo)
	On Timer indicator		Low
			Low
	indicator		Medium
	indicator		High
			High
			d’light Cool indicator

Battery changing time

When the battery is exhausted, () will be displayed in the remote controller display. When the icon appears, change the batteries. The remote controller requires two 1.5V AAA type batteries.

Storing the remote controller

When you do not use the remote controller for long time, remove the batteries from the remote controller and store it.

Inserting the batteries

ENGLISH

1.Push the lever as arrow indicates on the rear side of the remote controller and pull up.

2.Insert two AAA batteries.

Check and match the“+”and“-” signs accordingly. Make sure you have inserted the batteries in correct position.

3.Close the cover by place it back to its original position.

You should hear click sound when the cover is locked properly.

• The signal may not be received well of electronic lighting style	lamps such as inverter	lamps
are in the same space.

•If other electrical products operate by the remote controller, call your nearest contact center.

9

Image 9

Contents Air Conditioner Contents Important safety symbols and precautions Safety precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges Checking before useChecking the name of the parts Power buttonMain parts DisplayRemote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasic function Press Button to adjust the temperaturePress the Air swing button on the remote controller Using the Turbo functionCirculate the air Position you preferMode Press the button Press the button to set the time Press the Set/Cancel button to active it onTimer 1 hour Using the Smart Saver functionTimer 5 hours From the moment you have set the timerUsing the Quiet function Cleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchangerClean the Air Cleaning the air conditionerSlide it down Dry the Ai lter in a ventilated areaPeriodical checks Maintaining the air conditionerTroubleshooting Outdoor unit Heat exchanger during Heat mode in winter If may not be aConnection Model Name Included Models Remark General informationInstalling the unit Choosing the installation locationPower supply line, fuse or circuit breaker Won’t be considered in-warranty and charged to end userModel Outdoor UnitWhen installing more than 1 outdoor unit  When the air outlet is towards the wallTop view Side view Accessories Accessories in the indoor unit caseAccessories in the outdoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the assembly cable Connecting the cableFix the indoor unit Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryThen pull it out through the appropriate hole Smooth the cut edgesCutting or extending the pipe Purging the indoor unitUnscrew the caps at the end of each pipe Connect the pipesCracked Correct InclinedApplying the following torque Outer DiameterChanging direction of the drain hose Drain hose installationExcessive torque can be cause of gas leakage Purging the connected pipesAdding Refrigerant Covered by the Kyoto Protocol 1975To check for gas leaks on the outdoor unit Performing the gas leak testsTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesFixing the outdoor unit in place Outdoor unit installed on the wall by rackPart without insulation on the end of the pipes Properly ModelPress the Power button and check the following Pump down procedure when removing the productPress the Mode button to select Cool or Heat mode Final Check and Trial OperationHow to connect your extended power cables Questions or COMMENTS?