Oreck 550, 700, 600 warranty Accessories, Concrete and Asphalt Applications

Page 10

E N G L I S H

Concrete and Asphalt

Applications

Removing Oil and Dirt

Greaselock® Absorbent Powder effectively and safely cleans concrete and asphalt without solvents. Greaselock® application is a natural mineral that absorbs and captures oil and dirt so it can be safely discarded or rinsed away.

Equipment and Material Required:

Orbiter® Multi-Floor Machine

Black Drive Pad Holder

Greaselock® Absorbent Powder

Brown Strip Pad

Orange Scrub Brush

Procedure:

To clean oil, dirt, mold and mildew from smooth concrete, use the Greaselock® Absorbent Powder and the brown strip pad. To clean rough or uneven concrete or asphalt, use Greaselock® Absorbent Powder and the orange scrub brush.

1.For fresh stains or spills that have not dried, use the Greaselock® Absorbent Powder as a dry powder. For dry stains, add a little water during mixing or scrubbing stage.

2.Liberally apply Greaselock® Absorbent Powder to spill or area to clean, completely covering it. Allow five to ten minutes to absorb for fresh stains, overnight for dried stains.

3.Use the Orbiter® Multi-Floor Machine and brown strip pad or orange scrub brush to agitate the powder on the floor. Mop or hose off floor if necessary.

See Greaselock® Absorbent Powder packaging for complete instructions.

Accessories

Oreck offers a full line of accessories to give you the tools you need for the job!

Depending on the unit purchased, some of the accessories below may be included with your Orbiter® Multi-Floor Machine. All of these accessories are available at one of our over 450 Oreck retail Stores or on our website, www.oreck.com.

When choosing different pads and brushes for the Orbiter®, there is no exact science to selecting an accessory for a particular floor. Bonnets are good for surface cleaning most floor types. Pads are good for scrubbing and polishing flat surfaces. Brushes work well for getting into recesses in non-flat surfaces, like tile, where the bristles can get into grout lines. When you choose an accessory, remember you want one aggressive enough to do the job but gentle enough not to damage the floor. Use common sense. For example, do not use a brown strip pad (aggressive) on a wood floor (soft floor). Start with what is safe and move to a more aggressive accessory, if needed.

Note: Oreck recommends removing brushes and pads when storing the Orbiter® Multi-Floor Machine. Accessories can become deformed if stored on the machine.

General

Black Drive Pad Holder 53178-51-0327 (Black plastic with teeth)

• Holds pads and bonnets in place

Bonnets

Bonnets are designed to surface clean most surfaces. They are washable and can be reused.

White Terrycloth Bonnet 437053

This bonnet cleans the traffic lane

and spots in the carpet without wetting the entire carpet.

Use with Oreck Premist® Soil Release Pre-Spray and Dry Carpet Cleaner.

When one side of bonnet is dirty, flip it over and use the other side.

When job is complete, clean terrycloth bonnet in washing machine using cold water or hose off and allow to air dry.

Lamb’s Wool Bonnet

437054

Designed to provide the best possible shine on wood, tile and vinyl floors.

Use the bonnet for everyday buffing to remove scuff marks.

When job is complete, clean lambs wool bonnet in washing machine using cold water or hose off and allow to air dry.

To use a bonnet, see “Attaching Accessories” on page 4 and “Removing Accessories” on page 5

Pads

Pads are designed to be porous and open-weave (except the beige pad) so that when it loosens dirt it can pick it up. The dirt goes inside the pad (i.e. off the floor). All pads can be turned over and the other side used before cleaning or disposing. Pads may be hosed off in some instances and re-used.

The pads are color coded depending on how aggressive they are (except for the beige marble pad): White is the softest, followed by blue medium aggressive, and brown being the most aggressive.

White Polish Pad

437051

(least aggressive)

 

Apply paste wax.

Clean and polish wood (coated & uncoated),linoleum, and laminate.

Cleans all surfaces except stone.

10

Image 10
Contents Orbiter Visit ONE of OUR Over 450 Store LocationsSafety General Information Table of ContentsWarranty Grounding InformationIntroduction Customer ServiceAttaching Accessories Getting StartedCarpet and Area Rug Applications Laminate, Vinyl Linoleum Floor Applications Surface CleaningDo not Allow Cleaning Solution to DRY on Floor ScrubbingSealed Hard Wood Floor Applications Surface Cleaning Sealed FloorsRefinishing Tile Floor Applications Surface Cleaning and Waxing Waxed Hard Wood FloorsDeep Cleaning Waxed Hard Wood Floor ApplicationsStone Floor Applications Light CleaningMarble Restoration Accessories Concrete and Asphalt ApplicationsBrushes Maintenance TroubleshootingUser Maintenance Sand ScreensTroubleshooting Guide Table des matières Informations Général ES ET DE SécuritéGarantie Informations de mise à la terreAvertissement Fixation des accessoires Service à la clientèlePour commencer Mise en marche/arrêt de la machine pour sols Démontage des accessoiresApplications sur Moquettes et tapis Guidage de la machine pour solsNettoyage de surface Applications sur sols Laminés, vinyle et linoléumNettoyage à la bonnette RécurageRestauration Laissez PAS LA Solution Nettoyante Sécher SUR LE SOLDécapage PrécautionsPassage à la toile abrasive Applications sur sols en Bois dur imprégnéNettoyage de surface de parquet imprégné Parquets en boisNettoyage de surface et cirage de parquets cirés Applications sur Sols carrelésApplications sur sols en Bois dur ciré Nettoyage en profondeurRestauration du marbre Applications sur sols en pierreApplications sur béton Et asphalte Élimination de l’huile et de la saletéBonnettes AccessoiresGénéraux TamponsToiles abrasives Entretien et dépannageBrosses Soins de votre machine pour sols OreckGuide de Dépannage Información General y De Seguridad Aplicación EN Pisos EnceradosGarantía Información para la puesta a tierraAtencion Servicio al Cliente IntroducciónPara empezar Instalación de accesoriosEncendido y apagado de la Máquina para Pisos Aplicación en alfombras TapetesExtracción de accesorios Manejo de la Máquina para PisosLimpieza superficial Aplicación en pisos laminados Vinílicos y de linóleoLimpieza con bonete FregadoPermita QUE LA Solución DE Limpieza SE Seque Sobre EL Piso DesprendimientoReacabado PrecaucionesPulido con mallas abrasivas Aplicación en pisos sellados De madera duraLimpieza superficial de pisos sellados Pisos de maderaLimpieza superficial y encerado de pisos de madera dura Aplicación en pisos De baldosasAplicación en pisos Encerados de madera dura Limpieza profundaRestauración de mármol Aplicación en pisos de piedraAplicación en concreto Asfalto Eliminación de aceite y suciedadBonetes AccesoriosDe uso general AlmohadillasMallas abrasivas Mantenimiento y Localización de fallasCepillos Cuidado de su Máquina Orbiter Multi-FloorGuía Para Identificación De Problemas