Tile Floor Applications, Sandscreening, Deep Cleaning

E N G L I S H

build-up of other floor cleaners. If necessary, repeat procedure until floor shines.

See Timberworks® bottle for complete instructions.

Sandscreening

(Wood Floors)

Sandscreening is ideal for refinishing the polyurethane coating on hard wood floors. The procedure is not designed to totally remove the old polyurethane, but smooth out imperfections and prime the floor for a new fresh coating. However, polyurethane coatings are generally very durable and look good for a long time - try a thorough cleaning before refinishing the polyurethane coating to see if the luster can be restored.

Equipment and Material Required:

Procedure:

1.Completely dust mop floor.

2.Wipe up spills with a dry cloth or paper towel. Use a slightly damp cloth for sticky spills. Hint: Buff with white polish pad to restore luster.

3.To apply paste wax: Attach black drive pad holder to Orbiter® Multi-Floor Machine. Apply a tablespoon

of paste wax on 4 sections of white polish pad. Place white polish pad on floor and center black drive pad holder onto pad. Work Orbiter® Multi-Floor Machine in a forward/back motion and spread out the paste wax to a thin coat. Allow paste wax to dry for

5 minutes. Turn white polish pad over to clean side and buff. Use tan polish brush or lamb’s wool bonnet to obtain a higher luster.

Helpful Hints:

•Orbiter® Multi-Floor Machine

•Black Drive Pad Holder

•Brown Strip Pad

•Sand Screen 60 grit

•Sand Screen 80 grit

•Sand Screen 100 grit

•Broom or Dust Mop

•Vacuum Cleaner

•Tack Rags

Procedure:

1.Use Orbiter® Multi-Floor Machine and the brown strip pad.

2.Place #60 grit sand screen disc under brown strip pad. Sand the floor. Remove residue by vacuuming or sweeping the floor in the same direction as the boards.

3.Place a #80 sand screen disc under the brown strip pad. Sand the floor.

4.Sweep and vacuum the floor, then tack rag

THOROUGHLY.

5.Apply finish according to manufacturer’s recommendations.

6.Burnish between coats with #100 grit sand screen disc and tack rag.

Surface Cleaning and Waxing

Waxed Hard Wood Floors

Waxed Hard Wood Floor

Applications

This procedure should be used on WAX FINISH floors only.

Equipment and Material Required:

•Orbiter® Multi-Floor Machine

•Black Drive Pad Holder

•Lamb’s Wool Bonnet

•Tan Polish Brush (Union Mix)

•White Polish Pad (optional)

•Paste Wax, 1 lb.

•Indian Sand Paste Wax

•Dust Mop

•Buffable Wax

1.When floor looks dull, try buffing first to see if that will restore the luster before re-waxing.

2.When areas of heavy use no longer respond to buffing, wax only those areas and buff all of the floor to an even luster.

3.Use clear paste wax to retain the floor’s natural color. Use Indian Sand Paste Wax to add a little color and help blend in blemishes on old floors.

Tile Floor Applications

Deep Cleaning

Equipment and Material Required:

•Orbiter® Multi-Floor Machine

•Black Drive Pad Holder

•Orange Scrub Brush or Black Carpet Brush

•White Terrycloth Bonnet

•Grunge Attack® Tile Floor Cleaner

Procedure:

Grunge Attack® Tile Floor Cleaner lifts dirt, grime and grease from tile floors and grout, leaving sparkling results.

1.Dilute Grunge Attack® Tile Floor Cleaner into a separate spray bottle according to the instructions on the bottle.

2.Lightly spray a 6 ft by 6 ft area with diluted Grunge Attack® Tile Floor Cleaner.

3.Clean with the Orbiter® Multi-Floor Machine and an orange scrub brush for ceramic tile floors or concrete. Use Orbiter® Multi-Floor Machine and the black carpet brush for delicate or glazed ceramic or porcelain tile floors.

4.Repeat steps 1 through 3 until the whole floor has been cleaned.

5.Go back over the cleaned floor with the Orbiter® Multi-Floor Machine and white terrycloth bonnet to remove all dirt lifted by the orange scrub brush. Wet floor as necessary with water or diluted Grunge Attack® Tile Floor Cleaner.

See Grunge Attack® Tile Floor Cleaner bottle for complete instructions.