Quadra-Fire CASTILEI-MBK owner manual Castile Pellet Insert Clearance To Combustibles, UL and ULC

Page 10

Castile Pellet Insert

R

B. Clearance To Combustibles, UL and ULC

NOTE: All Clearances are Minimum Clearances

AS A BUILT-IN

A	C	D
B		B
C
0 in. Clearance To Exposed Section And Face Trim

Figure 10.1			Must be installed in a non-tapered enclosure.

					Inches	Millimeters
	A	Top of Hopper		Top Vent	2.0	51
				Rear Vent	2.5	64
	B	Side of Hopper		Top or Rear Vent	2.0	51
	C	Back of Hopper		Top or Rear Vent	4.0	102
	D	Vent Pipe to Combustible		Top or Rear Vent	3.0	76

INSTALLED AS A BUILT-IN UNIT

Shown with Rear Vent and Outside Air

Combustible	12 in
Mantel	12 in
	(305mm)
		6 in
	Top Vent:	(152mm)
	2 in. (51mm)
	Rear Vent:
	2.5 in (64mm)
	Back of Hopper:
	4 in (102mm)
	Vent Pipe to	Outside Air
	Combustibles:
	3 in (76mm)

Figure 10.2

WARNING

Fire Risk.

Comply with all minimum clear- ances to combustibles as speci- ﬁed.

Failure to comply may cause house ﬁre.

NOTE:

•Illustrations reﬂ ect typical installations and are FOR DESIGN PURPOSES ONLY.

•Illustrations/diagrams are not drawn to scale.

•Actual installation may vary due to individual design preference.

Page 10

7022-122

January 19, 2011

Image 10

Contents Castile Pellet Insert Hot glass will cause burnsCastile Pellet Insert Welcome to the Quadra-Fire FamilyTable of Contents Mobile Home Approved Listing and Code ApprovalsAppliance Certiﬁcation BTU & Efﬁciency Speciﬁcations Glass SpeciﬁcationsGetting Started Appliance LocationNegative Pressure Castile Pellet Insert Locating Your Appliance & ChimneyDraft Minimum Vacuum Requirements 095Vent Conﬁgurations Negative Pressure, Shut-Down and Electrical Power FailureCastile Pellet Insert Avoiding Smoke and Odors Outside AirTools And Supplies Needed Castile Pellet Insert Fire SafetyInspect Appliance & Components Pre-Burn Check List3Dimensions and Clearances Appliance DimensionsCastile Pellet Insert Clearance To Combustibles, UL and ULC Must be installed in a non-tapered enclosureShown with Rear Vent and Outside Air Castile Pellet Insert Floor Protection Masonry and Factory-Built FireplacesMinimum Opening for Masonry and Factory-Built Fireplaces Prefabricated Metal ChimneyUsing a saws-all, cut out the ﬂoor Altering the Factory-Built FireplaceChimney and Exhaust Connection Vent InformationVenting Termination Requirements HorizontalHori tal Run,RunftFT Castile Pellet Insert Pellet Venting ChartsMinimum Vent for One Elbow MinimumVertical Vent for Three Elbows5Venting Systems Full Reline With Horizontal Outside AirCastile Pellet Insert Full Reline With Vertical Outside Air Mobile Home Installation 6Mobile HomeLeveling System 7Appliance Set-UpOutside Air Kit Instructions Ance. Shown in Figures 18.1Castile Pellet Insert Door Handle Removal Adjustable Hearth SupportDoor Removal Ex the sides into a bowed position before installing 20.7Surround & Trim Set, Econo 21.4Piece. Figure Castile Pellet Insert Surround & Trim Set, Econo Cont’dSurround and Cast Trim Set Shown in Figure .2 onTwo Piece Log Set Installation Castile Pellet Insert Thermostat Installation Combustible/Non-Combustible Materials Operating InstructionsFuel Material and Fuel Storage Clear Space Castile Pellet Insert General Operating InformationBefore Your First Fire Thermostat Calls For HeatFeed Rate Adjustment Instructions Fire CharacteristicsCastile Pellet Insert Starting Your First Fire Frequently Asked Questions Castile Pellet Insert Ignition CyclesTurn down thermostat and let the appliance completely cool Page Symptom Possible Cause Corrective Action Types of Fuel Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance FrequencySee .1 on Ash Removal from Firebox Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning Ash Drawer Disposal of Ashes Frequency As neededCleaning the Glass Cleaning Heat Exchanger TubesCleaning Beneath Heat Exchanger Door Latch InspectionCleaning Convection Blower Requires No Lubrication Cleaning the HopperCleaning Exhaust Blower Requires No Lubrication Preparing Firebox for Non-Burn SeasonCastile Pellet Insert High Ash Fuel Maintenance Immediate Attention and Cleaning is RequiredCastile Pellet Insert Combustion Blower Replacement Convection Blower ReplacementCastile Pellet Insert Igniter Replacement Glass ReplacementRe-installing Bafﬂe & Brick Set Castile Pellet Insert Bafﬂe & Brick Set RemovalCastile Pellet Insert Re-installing Bafﬂe & Brick Set Cont’d Reference Materials Component FunctionThermostat Vacuum SwitchWiring Schematic See .1 below Snap Disc #1 Convection Blower 110FCleaning Rods & Heat Exchanger Tubes Castile Pellet Insert Component LocationsPart number list on following pages Service PartsCastile Pellet Insert At Depot Stocked#28 Feed Assembly #23 Door AssemblyStocked at Depot Stocked #38 Firepot and Associted PartsOptional Accessories SP-CSTLI5134 Description Comments Part Number Fasteners Service And Maintenance Log Service And Maintenance Log Cont’d Homeowner’s Notes Limited Lifetime Warranty Warranty Conditions Contact Information