Quadra-Fire CASTILEI-MBK owner manual 6Mobile Home, Mobile Home Installation

Page 17

R

Castile Pellet Insert

6Mobile Home

A. Mobile Home Installation

You must use a Quadra-Fire Outside Air Kit for instal- lation in a mobile home.

1.An outside air inlet must be provided for the combustion air and must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while the appliance is in use to prevent room air starvation which causes smoke spillage. Smoke spillage can also set off smoke alarms.

2.The combustion air duct system must be made of metal. It must permit zero clearance to combustible construction and prevent material from dropping into the inlet or into the area beneath the dwelling and contain a rodent screen.

3.The appliance must be secured to the mobile home structure by bolting it to the fl oor (using lag bolts). Use the same holes that secured the appliance to the ship- ping pallet with a minimum of two attachment points.

4.The appliance must be grounded with #8 solid copper grounding wire or equivalent, terminated at each end with an NEC approved grounding/bonding connector.

5.Refer to clearances to combustibles and floor protection requirements on pages 9 to 11 for listings to combus- tibles and appropriate chimney systems.

6.Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the the exterior of the structure.

7.Follow the chimney manufacturer’s instructions when installing the vent system for use in a mobile home.

8.Installation shall be in accordance with the Manufactur- ers Home & Safety Standard (HUD) CFR 3280, Part 24.

CAUTION

THE STRUCTURAL INTEGRITY OF THE MANUFAC- TURED HOME FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.

Do NOT cut through:

Floor joist, wall, studs or ceiling trusses.

Any supporting material that would affect the structural integrity.

Spark Arrestor Cap

Storm Collar

Roof Flashing

Joist Shield/Firestop

Approved Class “L”

“PL” Pellet Vent

Figure 16.1

WARNING

Installation must comply with Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24.

WARNING

Asphyxiation Risk.

NEVER INSTALL IN A SLEEPING ROOM. Consumes oxygen in the room.

January 19, 2011

7022-122

Page 17

Image 17
Contents Hot glass will cause burns Castile Pellet InsertWelcome to the Quadra-Fire Family Castile Pellet InsertTable of Contents Appliance Certification BTU & Efficiency Specifications Listing and Code ApprovalsMobile Home Approved Glass SpecificationsAppliance Location Getting StartedDraft Castile Pellet Insert Locating Your Appliance & ChimneyNegative Pressure Minimum Vacuum Requirements 095Castile Pellet Insert Avoiding Smoke and Odors Negative Pressure, Shut-Down and Electrical Power FailureVent Configurations Outside AirInspect Appliance & Components Castile Pellet Insert Fire SafetyTools And Supplies Needed Pre-Burn Check ListAppliance Dimensions 3Dimensions and ClearancesShown with Rear Vent and Outside Air Must be installed in a non-tapered enclosureCastile Pellet Insert Clearance To Combustibles, UL and ULC Minimum Opening for Masonry and Factory-Built Fireplaces Masonry and Factory-Built FireplacesCastile Pellet Insert Floor Protection Prefabricated Metal ChimneyAltering the Factory-Built Fireplace Using a saws-all, cut out the floorVenting Termination Requirements Vent InformationChimney and Exhaust Connection Minimum Vent for One Elbow Castile Pellet Insert Pellet Venting ChartsHorizontalHori tal Run,RunftFT MinimumVertical Vent for Three ElbowsFull Reline With Horizontal Outside Air 5Venting SystemsCastile Pellet Insert Full Reline With Vertical Outside Air 6Mobile Home Mobile Home InstallationOutside Air Kit Instructions 7Appliance Set-UpLeveling System Ance. Shown in Figures 18.1Door Removal Adjustable Hearth SupportCastile Pellet Insert Door Handle Removal 20.7 Ex the sides into a bowed position before installing21.4 Surround & Trim Set, EconoSurround and Cast Trim Set Castile Pellet Insert Surround & Trim Set, Econo Cont’dPiece. Figure Shown in Figure .2 onTwo Piece Log Set Installation Castile Pellet Insert Thermostat Installation Fuel Material and Fuel Storage Operating InstructionsCombustible/Non-Combustible Materials Before Your First Fire Castile Pellet Insert General Operating InformationClear Space Thermostat Calls For HeatCastile Pellet Insert Starting Your First Fire Fire CharacteristicsFeed Rate Adjustment Instructions Castile Pellet Insert Ignition Cycles Frequently Asked QuestionsTurn down thermostat and let the appliance completely cool Page Symptom Possible Cause Corrective Action Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartTypes of Fuel FrequencyCleaning Ash Drawer Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Cleaning Heat Exchanger TubesCleaning the Glass Door Latch InspectionCleaning Exhaust Blower Requires No Lubrication Cleaning the HopperCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn SeasonImmediate Attention and Cleaning is Required Castile Pellet Insert High Ash Fuel MaintenanceConvection Blower Replacement Castile Pellet Insert Combustion Blower ReplacementGlass Replacement Castile Pellet Insert Igniter ReplacementCastile Pellet Insert Baffle & Brick Set Removal Re-installing Baffle & Brick SetCastile Pellet Insert Re-installing Baffle & Brick Set Cont’d Component Function Reference MaterialsWiring Schematic See .1 below Vacuum SwitchThermostat Snap Disc #1 Convection Blower 110FCastile Pellet Insert Component Locations Cleaning Rods & Heat Exchanger TubesCastile Pellet Insert Service PartsPart number list on following pages Stocked At DepotStocked at Depot #23 Door Assembly#28 Feed Assembly #38 Firepot and Associted Parts StockedOptional Accessories SP-CSTLI5134 Description Comments Part Number Fasteners Service And Maintenance Log Service And Maintenance Log Cont’d Homeowner’s Notes Limited Lifetime Warranty Warranty Conditions Contact Information