Quadra-Fire CASTILEI-MBK owner manual 3Dimensions and Clearances, Appliance Dimensions

Page 9

R

Castile Pellet Insert

3Dimensions and Clearances

A. Appliance Dimensions

27-7/8 in. (707mm)

23-3/8 in. (594mm)

8 in.

(203mm)

32-1/4 in. (819mm)

Figure 9.1 - Top View

	24-3/4 in.		19 in.
	(629mm)		(483mm)
	9-3/4 in.	13 in.	2 in.
	(249mm)	(330mm)	2 in.
	(249mm)	(330mm)	(51mm)
			(51mm)

Figure 9.2 -Side View

A

B

Figure 9.3- Front View

	Overall Size		A	B
	Metal Surround w/Cast Trim, STD		42-1/2 in. (1080mm)	30 in. (762mm)
	Metal Surround w/Cast Trim, LRG		48 in. (1219mm)	34 in. (864mm)
	Metal Surround w/Standard Trim, STD		43 in. (1092mm)	31 in. (787mm)
	Metal Surround w/Standard Trim, LRG		51 in. (1294mm)	34 in. (864mm)


January 19, 2011		7022-122			Page 9

Image 9

Contents Hot glass will cause burns Castile Pellet InsertWelcome to the Quadra-Fire Family Castile Pellet InsertTable of Contents Appliance Certiﬁcation BTU & Efﬁciency Speciﬁcations Listing and Code ApprovalsMobile Home Approved Glass SpeciﬁcationsAppliance Location Getting StartedDraft Castile Pellet Insert Locating Your Appliance & ChimneyNegative Pressure Minimum Vacuum Requirements 095Castile Pellet Insert Avoiding Smoke and Odors Negative Pressure, Shut-Down and Electrical Power FailureVent Conﬁgurations Outside AirInspect Appliance & Components Castile Pellet Insert Fire SafetyTools And Supplies Needed Pre-Burn Check ListAppliance Dimensions 3Dimensions and ClearancesMust be installed in a non-tapered enclosure Castile Pellet Insert Clearance To Combustibles, UL and ULCShown with Rear Vent and Outside Air Minimum Opening for Masonry and Factory-Built Fireplaces Masonry and Factory-Built FireplacesCastile Pellet Insert Floor Protection Prefabricated Metal ChimneyAltering the Factory-Built Fireplace Using a saws-all, cut out the ﬂoorVent Information Chimney and Exhaust ConnectionVenting Termination Requirements Minimum Vent for One Elbow Castile Pellet Insert Pellet Venting ChartsHorizontalHori tal Run,RunftFT MinimumVertical Vent for Three ElbowsFull Reline With Horizontal Outside Air 5Venting SystemsCastile Pellet Insert Full Reline With Vertical Outside Air 6Mobile Home Mobile Home InstallationOutside Air Kit Instructions 7Appliance Set-UpLeveling System Ance. Shown in Figures 18.1Adjustable Hearth Support Castile Pellet Insert Door Handle RemovalDoor Removal 20.7 Ex the sides into a bowed position before installing21.4 Surround & Trim Set, EconoSurround and Cast Trim Set Castile Pellet Insert Surround & Trim Set, Econo Cont’dPiece. Figure Shown in Figure .2 onTwo Piece Log Set Installation Castile Pellet Insert Thermostat Installation Operating Instructions Combustible/Non-Combustible MaterialsFuel Material and Fuel Storage Before Your First Fire Castile Pellet Insert General Operating InformationClear Space Thermostat Calls For HeatFire Characteristics Feed Rate Adjustment InstructionsCastile Pellet Insert Starting Your First Fire Castile Pellet Insert Ignition Cycles Frequently Asked QuestionsTurn down thermostat and let the appliance completely cool Page Symptom Possible Cause Corrective Action Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartTypes of Fuel FrequencyCleaning Ash Drawer Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Cleaning Heat Exchanger TubesCleaning the Glass Door Latch InspectionCleaning Exhaust Blower Requires No Lubrication Cleaning the HopperCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn SeasonImmediate Attention and Cleaning is Required Castile Pellet Insert High Ash Fuel MaintenanceConvection Blower Replacement Castile Pellet Insert Combustion Blower ReplacementGlass Replacement Castile Pellet Insert Igniter ReplacementCastile Pellet Insert Bafﬂe & Brick Set Removal Re-installing Bafﬂe & Brick SetCastile Pellet Insert Re-installing Bafﬂe & Brick Set Cont’d Component Function Reference MaterialsWiring Schematic See .1 below Vacuum SwitchThermostat Snap Disc #1 Convection Blower 110FCastile Pellet Insert Component Locations Cleaning Rods & Heat Exchanger TubesService Parts Part number list on following pagesCastile Pellet Insert Stocked At Depot#23 Door Assembly #28 Feed AssemblyStocked at Depot #38 Firepot and Associted Parts StockedOptional Accessories SP-CSTLI5134 Description Comments Part Number Fasteners Service And Maintenance Log Service And Maintenance Log Cont’d Homeowner’s Notes Limited Lifetime Warranty Warranty Conditions Contact Information