Napoleon Fireplaces GDS60N manual Installing Flashing and Storm Collar

Page 33

33

2 FT MIN

3

FT

10 FT

MIN

FIGURE 5.7.5b

7” OPTIONAL VENT PIPE

4” “B” VENT

SECURELY

ATTACH VENT

ADAPTER TO

FLUE COLLAR

5.7.6 INSTALLING FLASHING AND STORM COLLAR

Remove nails from the shingles above and to the sides of the chim- ney. Place the ﬂashing over the vent pipe and slide it underneath the sides and upper edge of the shingles. Ensure that the vent pipe is properly centered within the ﬂashing, giving a 3/4" margin all around. Fasten to the roof on the top and sides.

Do not nail through the lower portion of the ﬂashing. Make weather- tight by sealing with caulking. Where possible, cover the sides and top edges of the ﬂashing with rooﬁng material.

Apply waterproof caulking around the vent, 1" above the top of the ﬂashing and push the storm collar down into the caulking. Attach a rain cap to the top of the last vent section.

CAULKING

STORM COLLAR

WEATHER

SEALANT

FLASHING

FIGURE 5.7.6

W415-0788 / A / 09.22.09

Image 33

Contents GDS60N & GS60N Table of Contents Installation Installation OverviewIntroduction General Instructions DimensionsGeneral Information We suggest that our gasModel Natural GAS/GAZ Natural Rating PlateShipping Bracket Care of GlassGlass Door Removal Shippingbracket LatchVenting Model GDS60 Refer to the section applicable to your installationPart Supplier Website Venting Lengths and ComponentsTypical Vent Installations Minimum Feet MaximumTOP Vent Minimum Feet Maximum Rear Vent Plus RiseMinimum Plus Rise Corner Termination Special Vent Installations 3.3.1 Periscope TerminationGrade To Grade MinimumVent Terminal Clearances Installations CanadaRear Exit Venting Application Flow Chart TOP ExitDefinitions Elbow Vent Length ValuesFeet Inches HT VT TOP Exit Horizontal TerminationFormula 1 HT VT Formula 2 HT + VT 40 FT Horizontal Vent RUN Plus Offset in Feet HT Rear Exit Horizontal Termination10c 11a TOP or Rear Exit Vertical Termination11c Installation Preparation Model GDS60 Orifice ReplacementRear Vent Termination Changing a TOP Vent to a Rear Vent Installation Minimum Clearance to CombustiblesMaintain These Minimum Clearances to Combustibles Wall and Ceiling Protection Horizontal InstallationHorizontal AIR Terminal Installation Model GDS60 Vertical InstallationHigh Temperature Sealant Inner Flex Pipe Vertical AIR Terminal Installation Model GDS60Roof Support Inner PipeGAS Installation Mobile Home Installation Model GDS60High Temperature Sealant Appliance Vent Connection Model GDS60Optional Wall Switch / Thermostat Vent Specifics Model GS60 5.7.1 Chimney InstallationWire Size MAX. Length Combustion AIR Installing B VentMore MIN Flat Roof Wall Adding Vent SectionsCaulking Storm Collar Weather Sealant Flashing Installing Flashing and Storm CollarFinishing Glass Door Installation and RemovalFront Cast Removal Return FlangeLOG Placement Glass / Door ReplacementLogo Placement Access Cover Plate Switch and Bracket InstallationSlot Removed Screws Optional Blower InstallationWiring Diagram Operation Operating InstructionsModel GS60 only Venting Action Check Lighting Instructions Anti Condensation SwitchPilot Burner Adjustment AdjustmentVenturi Adjustment Flame CharacteristicsMaintenance Common Components ReplacementsGS60 Components Roof Terminal Kits 49 50 Symptom Problem Trouble ShootingSymptom Problem Test Solution GDS600 only HOTGlass Embers only GS600 onlyConditions and Limitations WarrantyAppliance Service History Service History