Honeywell VISTA-10PSIA setup guide Important Installation Highlights Installer Please Read

Page 6

Installation and Setup Guide

NOTE: All devices and accessories used in a Canadian installation must be Listed for use in Canada.

Important Installation Highlights (Installer Please Read)

•This system uses addressable keypads and Relay Modules (see table of addresses in Programming Overview section).

•Keypads must be set for addresses 16-23 (first keypad is address 16, which is different from previous controls) and programmed in data fields *190-*196.

•4204 Relay Modules must be set for specific address 12 (see Connecting Relay Modules section).

•Relays have two programming menu modes: Use *79 Menu mode to map module addresses and device (output) numbers. Use *80 Menu mode to define the output functions (see Output Device Programming section).

•This system supports programmable function keys. Use *57 Menu mode to define the function keys (see Function Key Programming section).

•This system provides various paging features. Refer to the Programming Overview section for a summary on pager programming.

1-2

Image 6

Contents Ademco VISTA-10P Ademco VISTA-10PSIA Recommendations for Proper Protection Table Of Contents Menu Mode Programming Testing the SystemSystem Communication and Operation Functions Features and Installation HighlightsCapabilities Compatible DevicesImportant Installation Highlights Installer Please Read Mounting and Wiring the Control Cabinet and LockMounting the PC Board Alone no RF Receiver Mounting Board with RF Receiver Mounting the PC Board and RF ReceiverKeypad Addresses Wiring to KeypadsSupplementary Power optional Size MA or less 100 mA 300 mA 500 mA 600 mAWire Run Chart Wiring the AC TransformerBackup Battery Distance from control Wire SizeAC Power Outlet Ground Earth GroundMetal Cold Water Pipe Smoke Detectors Hardwire ZonesWire Smoke Detectors Normally Open Zones/ Normally Open Eolr ZonesInstalling the RF Receiver Installing a 5800TM ModuleRF Receiver No. of Zones Installing the Transmitters Installing a KeyswitchTransmitter Battery Life Connecting Relay Modules Keyswitch Wiring ConnectionsOn-Board Trigger Connector with 4-Wire Cable On-Board TriggersPhone Line/Phone Module Connections Phone Module Problems Long Range Radio ConnectionsAudio Alarm Verification Connections AAV, listen-In RJ31XAbout Programming To enable keypadsProgramming Overview KeypadsFunction Keys Wireless Receiver, Transmitters, and Wireless Keys keyfobsPager Programming Output DevicesZone Type Definitions Configurable No Alarm ResponseKeyswitch Monitor ZoneExiting the Programming Mode Menu Mode Programming ∗56, *57, ∗58, ∗79, ∗80, ∗81, ∗82Loading Factory Defaults/Initializing for Download Task ProcedureReports as†† Enabled By… Table of Device AddressesAbout Data Field Programming System Setup FieldsData Field Programming Programming Data FieldsZone Sounds & Timing Dialer Programming System Status Report Codes Trouble Restore Report Code Cancel Report CodeAlarm Restore Report Code Bypass Restore Report CodeMiscellaneous System Fields Option Selection Event Log EnablesEvent Log Full Report Code No. of Reports In Armed Period per Zone Swinger SuppressionPager Programming Fields Configurable Zone Type Options Configurable Zone Type Programming FieldsConfigurable Zone Type Zone Type 90 Report CodesConfigurable Zone Type Charts Zone Conditions Represented EntriesKeypad Programming Fields Installation Instructions Zone Programming Overview ∗56 and ∗58 Menu Modes Menu Mode ProgrammingZone Programming Procedure SET to CONFIRM? 0 = no 1 = YESInput S/N Input Type RF TransInput S/N L Xmit to Confirm∗58 Expert Programming Mode Procedures Completing Zone ProgrammingProgram ALPHA? 0 = no 1 = YES Wireless Key Programming Templates RC in LTemplate ? Input S/N AXXX-XXXX Wireless Key Predefined Default TemplatesWireless Key Transmitter Xmit to Confirm Press to Skip∗79 Menu Mode Output Device Programming Overview *79/*80 Menu ModeMenu Mode Output Device Mapping Output Device programming involvesOutput Definition Components Menu Mode Defining Output Functions∗80 Menu Mode Prompt EntryE P Trig Zone List Programming Zone List Overview ∗81 Menu ModeMenu Mode List No Used for…Press the desired function key, A-D Function Key Programming Overview ∗57 Menu ModeProgramming Function Keys Is no longer available to be used as an endAbout Descriptor Programming Overview ∗82 Menu Mode Programming Zone Descriptors Menu mode ∗82When defining descriptors ZN 01 Back Door ZN 01 Back D OORZN 01 Back Door Custom?Character Ascii Chart For Adding Custom Words For Entering Zone DescriptorsProgramming Installer and User Schedules System Operation section= group number Installation Instructions System Communication and Operation System Communication OverviewReport Code Formats Where Code for Type +1/4+1 Report Standard ExpandedAdemco Contact ID Code DefinitionMaximum Setting the Real-Time Clock User Security CodesLevel User No Functions Voice Keypads Keypad CommandsKeypad Functions Function DescriptionMeaning Various System Trouble DisplaysAlpha Display Keys Displayed as ZoneChecking Transmitter Enrollment Sniffer Mode Testing the SystemAbout Test Procedures System TestDialer Communication Test and Periodic Test Reports Go/No Go Test ModeAutomatic Standby Battery Tests Automatic Periodic Test ReportPhone Modules Specifications & AccessoriesRelay Module Long Range RadioSeries Transmitter Input Loop Identification Compatible 5800 Series Transmitters TableModel Product Input Type Description 5827 Wireless Keypad Can be used to turn the burglary protection on and offInstallation Instructions Industry Canada Industrie CanadaFederal Communications Commission FCC Part FCC PartUL Notices SIA Quick Reference GuideLimitations and Warranty Limitations of this Alarm System10-2 Index 10-4 Summary of Connections Limited Warranty K0735V3 10/04 Rev. B