Honeywell Ademco Security Systems, VISTA-10PSIA setup guide Mounting Board with RF Receiver

Page 8

Installation Instructions

Mounting Board with RF Receiver

1.a.Remove the receiver board from its case, then insert the top of the board into the slots at the top of the cabinet, as shown in Detail A in Figure 3. Make sure that the board rests on the correct row of tabs.

b.Swing the base of the board into the mounting clips and secure it to the cabinet with the accompanying screws.

c.Insert the top of the control's board into the slot in the clips and position two clips at the lower edge of the board.

d.Swing this board into place and secure it with two additional screws.

2.Insert grounding lugs (supplied with the receiver) through the top of the cabinet into the left- hand terminals of the antenna blocks (at the upper edge of the receiver board) and secure them to the cabinet top with the screws provided, as shown in Detail B.

3.Insert the receiver's antennas through the top of the cabinet, into the blocks' right-hand terminals, and tighten the screws.

NOTES

•Do not mount the cabinet on or near metal objects. This will decrease RF range and/or block RF transmissions from wireless transmitters.

•Do not locate the cabinet in an area of high RF interference (revealed by frequent or prolonged lighting of the LED in the receiver after it is operational (random flicker is OK)

CABINET	A	B
	A	B
		CABINET
		BOARD
	RECEIVER CIRCUIT BOARD	SUPPORTING
		SLOTS

+	+
	CIRCUIT
	BOARD
	MOUNTING
	CLIP

CONTROL

CIRCUIT

BOARD

	DETAIL A
MOUNTING	SIDE VIEW
CLIP	OF BOARD -

SUPPORTING SLOTS

INSTALLATION WITH RECEIVER CIRCUIT BOARD

WHITE	BLACK	RED
MOUNTING	MOUNTING	MOUNTING
CLIP	CLIP	CLIP

NOTE

A COMBINATION OF THESE MOUNTING CLIPS HAS BEEN INCLUDED IN YOUR INSTALLATION KIT.

USE THE APPROPRIATE CLIPS FOR MOUNTING.

IF NO RF RECEIVER IS USED, MOUNT THE PC BOARD USING EITHER THE WHITE OR BLACK CLIPS, WHICHEVER ARE INCLUDED IN THE CONTROL PANEL'S HARDWARE KIT.

ANTENNA

(2)

SCREW

(2)

GROUNDING LUG

(2)

ANTENNA

MOUNT

(2 PLACES)

DETAIL B

ANTENNA AND GROUNDING

LUG INSTALLATION

pc_mount-001-V1

Figure 3. Mounting the PC Board and RF Receiver

2-2

Image 8

Contents Ademco VISTA-10P Ademco VISTA-10PSIA Recommendations for Proper Protection Table Of Contents System Communication and Operation Menu Mode ProgrammingTesting the System Features and Installation Highlights CapabilitiesFunctions Compatible DevicesImportant Installation Highlights Installer Please Read Mounting the PC Board Alone no RF Receiver Mounting and Wiring the ControlCabinet and Lock Mounting Board with RF Receiver Mounting the PC Board and RF ReceiverWiring to Keypads Supplementary Power optionalKeypad Addresses Size MA or less 100 mA 300 mA 500 mA 600 mAWiring the AC Transformer Backup BatteryWire Run Chart Distance from control Wire SizeMetal Cold Water Pipe AC Power Outlet GroundEarth Ground Hardwire Zones Wire Smoke DetectorsSmoke Detectors Normally Open Zones/ Normally Open Eolr ZonesRF Receiver No. of Zones Installing the RF ReceiverInstalling a 5800TM Module Transmitter Battery Life Installing the TransmittersInstalling a Keyswitch Connecting Relay Modules Keyswitch Wiring ConnectionsPhone Line/Phone Module Connections On-Board Trigger Connector with 4-Wire CableOn-Board Triggers Phone Module Problems Long Range Radio ConnectionsAudio Alarm Verification Connections AAV, listen-In RJ31XTo enable keypads Programming OverviewAbout Programming KeypadsWireless Receiver, Transmitters, and Wireless Keys keyfobs Pager ProgrammingFunction Keys Output DevicesZone Type Definitions No Alarm Response KeyswitchConfigurable Monitor ZoneMenu Mode Programming ∗56, *57, ∗58, ∗79, ∗80, ∗81, ∗82 Loading Factory Defaults/Initializing for DownloadExiting the Programming Mode Task ProcedureReports as†† Enabled By… Table of Device AddressesSystem Setup Fields Data Field ProgrammingAbout Data Field Programming Programming Data FieldsZone Sounds & Timing Dialer Programming System Status Report Codes Cancel Report Code Alarm Restore Report CodeTrouble Restore Report Code Bypass Restore Report CodeMiscellaneous System Fields Event Log Enables Event Log Full Report CodeOption Selection No. of Reports In Armed Period per Zone Swinger SuppressionPager Programming Fields Configurable Zone Type Programming Fields Configurable Zone TypeConfigurable Zone Type Options Zone Type 90 Report CodesConfigurable Zone Type Charts Zone Conditions Represented EntriesKeypad Programming Fields Installation Instructions Menu Mode Programming Zone Programming ProcedureZone Programming Overview ∗56 and ∗58 Menu Modes SET to CONFIRM? 0 = no 1 = YESInput Type RF Trans Input S/N LInput S/N Xmit to ConfirmProgram ALPHA? 0 = no 1 = YES ∗58 Expert Programming Mode ProceduresCompleting Zone Programming Template ? Wireless Key Programming TemplatesRC in L Wireless Key Predefined Default Templates Wireless Key TransmitterInput S/N AXXX-XXXX Xmit to Confirm Press to SkipOutput Device Programming Overview *79/*80 Menu Mode Menu Mode Output Device Mapping∗79 Menu Mode Output Device programming involvesMenu Mode Defining Output Functions ∗80 Menu ModeOutput Definition Components Prompt EntryE P Trig Zone List Overview ∗81 Menu Mode Menu ModeZone List Programming List No Used for…Function Key Programming Overview ∗57 Menu Mode Programming Function KeysPress the desired function key, A-D Is no longer available to be used as an endWhen defining descriptors About Descriptor Programming Overview ∗82 Menu ModeProgramming Zone Descriptors Menu mode ∗82 ZN 01 Back D OOR ZN 01 Back DoorZN 01 Back Door Custom?Character Ascii Chart For Adding Custom Words For Entering Zone DescriptorsProgramming Installer and User Schedules System Operation section= group number Installation Instructions Report Code Formats System Communication and OperationSystem Communication Overview Where Code for Type +1/4+1 Report Standard ExpandedMaximum Ademco Contact IDCode Definition Level User No Functions Setting the Real-Time ClockUser Security Codes Keypad Commands Keypad FunctionsVoice Keypads Function DescriptionVarious System Trouble Displays Alpha DisplayMeaning Keys Displayed as ZoneTesting the System About Test ProceduresChecking Transmitter Enrollment Sniffer Mode System TestGo/No Go Test Mode Automatic Standby Battery TestsDialer Communication Test and Periodic Test Reports Automatic Periodic Test ReportSpecifications & Accessories Relay ModulePhone Modules Long Range RadioModel Product Input Type Description Series Transmitter Input Loop IdentificationCompatible 5800 Series Transmitters Table 5827 Wireless Keypad Can be used to turn the burglary protection on and offInstallation Instructions Industrie Canada Federal Communications Commission FCC PartIndustry Canada FCC PartUL Notices SIA Quick Reference GuideLimitations and Warranty Limitations of this Alarm System10-2 Index 10-4 Summary of Connections Limited Warranty K0735V3 10/04 Rev. B