Honeywell VISTA-10PSIA Function Key Programming Overview ∗57 Menu Mode, Programming Function Keys

Page 46

Installation Instructions

Function Key Programming Overview (∗57 Menu Mode)

The system provides the ability to program each of the four keypad function keys to perform one of 12 system operations. The end user can then activate the function by simply pressing and holding the programmed key for 2 seconds. Typical functions (listed below) include single-button arming, turning lights on/off, or single-button paging.

Programming Function Keys

Function key programming involves:

1.Assigning the function key number;

2.Selecting the desired function for that key.

Start Function Key Programming mode by pressing ✱57 while in Data Programming mode. The following prompts are displayed:

PROMPT

Press Key to Pgm
0 = Quit	0

	VALID ENTRIES	EXPLANATION
	Press the desired function key, A-D.		A		1	OFF	2	AWAY	3	STAY

	NOTE: A key programmed as a function key		B		4		5		6
	is no longer available to be used as an end-					MAX		TEST		BYPASS

	user macro key or panic key.		C		7		8		9
	[∗] to continue					INSTANT		CODE		CHECK

			D		* READY		0		#

keypad_keys-00-001-V0

Key "A" Func
Zone 95	00

Enter the desired function for this key:

00 = For the Function key selected, the function will be as follows (system default): If A selected = Zone 95 (emergency key, same as [1] [∗] pair)

If B selected = Zone 99 (emergency key, same as [∗] [#] pair) If C selected = Zone 96 (emergency key, same as [3] [#] pair) If D selected = Single-button paging

01 = Single-button paging (sends a 999-9999 message to pager)

02 = Display time

03 = Arm AWAY (reports as User 00 if closing reports are enabled)

04 = Arm STAY (reports as User 00 if closing reports are enabled)

05 = Arm NIGHT-STAY (reports as User 00 if closing reports enabled)

06 = Step Arming (arms STAY, then NIGHT-STAY†, then AWAY)

07 = Output Device Command (for device programmed as system operation type 66 in *80 Menu Mode)

08 = Communication Test (sends Contact ID code 601) 09= Macro Key (defined by [#] [6] [6] command)

[∗] to continue; returns to key number prompt with the next function key letter displayed.

† If Night-Stay zones are listed in zone list 5

5-10

Image 46

Contents Ademco VISTA-10P Ademco VISTA-10PSIA Recommendations for Proper Protection Table Of Contents Testing the System Menu Mode ProgrammingSystem Communication and Operation Functions Features and Installation HighlightsCapabilities Compatible DevicesImportant Installation Highlights Installer Please Read Cabinet and Lock Mounting and Wiring the ControlMounting the PC Board Alone no RF Receiver Mounting Board with RF Receiver Mounting the PC Board and RF ReceiverKeypad Addresses Wiring to KeypadsSupplementary Power optional Size MA or less 100 mA 300 mA 500 mA 600 mAWire Run Chart Wiring the AC TransformerBackup Battery Distance from control Wire SizeEarth Ground AC Power Outlet GroundMetal Cold Water Pipe Smoke Detectors Hardwire ZonesWire Smoke Detectors Normally Open Zones/ Normally Open Eolr ZonesInstalling a 5800TM Module Installing the RF ReceiverRF Receiver No. of Zones Installing a Keyswitch Installing the TransmittersTransmitter Battery Life Connecting Relay Modules Keyswitch Wiring ConnectionsOn-Board Triggers On-Board Trigger Connector with 4-Wire CablePhone Line/Phone Module Connections Phone Module Problems Long Range Radio ConnectionsAudio Alarm Verification Connections AAV, listen-In RJ31XAbout Programming To enable keypadsProgramming Overview KeypadsFunction Keys Wireless Receiver, Transmitters, and Wireless Keys keyfobsPager Programming Output DevicesZone Type Definitions Configurable No Alarm ResponseKeyswitch Monitor ZoneExiting the Programming Mode Menu Mode Programming ∗56, *57, ∗58, ∗79, ∗80, ∗81, ∗82Loading Factory Defaults/Initializing for Download Task ProcedureReports as†† Enabled By… Table of Device AddressesAbout Data Field Programming System Setup FieldsData Field Programming Programming Data FieldsZone Sounds & Timing Dialer Programming System Status Report Codes Trouble Restore Report Code Cancel Report CodeAlarm Restore Report Code Bypass Restore Report CodeMiscellaneous System Fields Option Selection Event Log EnablesEvent Log Full Report Code No. of Reports In Armed Period per Zone Swinger SuppressionPager Programming Fields Configurable Zone Type Options Configurable Zone Type Programming FieldsConfigurable Zone Type Zone Type 90 Report CodesConfigurable Zone Type Charts Zone Conditions Represented EntriesKeypad Programming Fields Installation Instructions Zone Programming Overview ∗56 and ∗58 Menu Modes Menu Mode ProgrammingZone Programming Procedure SET to CONFIRM? 0 = no 1 = YESInput S/N Input Type RF TransInput S/N L Xmit to ConfirmCompleting Zone Programming ∗58 Expert Programming Mode ProceduresProgram ALPHA? 0 = no 1 = YES RC in L Wireless Key Programming TemplatesTemplate ? Input S/N AXXX-XXXX Wireless Key Predefined Default TemplatesWireless Key Transmitter Xmit to Confirm Press to Skip∗79 Menu Mode Output Device Programming Overview *79/*80 Menu ModeMenu Mode Output Device Mapping Output Device programming involvesOutput Definition Components Menu Mode Defining Output Functions∗80 Menu Mode Prompt EntryE P Trig Zone List Programming Zone List Overview ∗81 Menu ModeMenu Mode List No Used for…Press the desired function key, A-D Function Key Programming Overview ∗57 Menu ModeProgramming Function Keys Is no longer available to be used as an endProgramming Zone Descriptors Menu mode ∗82 About Descriptor Programming Overview ∗82 Menu ModeWhen defining descriptors ZN 01 Back Door ZN 01 Back D OORZN 01 Back Door Custom?Character Ascii Chart For Adding Custom Words For Entering Zone DescriptorsProgramming Installer and User Schedules System Operation section= group number Installation Instructions System Communication Overview System Communication and OperationReport Code Formats Where Code for Type +1/4+1 Report Standard ExpandedCode Definition Ademco Contact IDMaximum User Security Codes Setting the Real-Time ClockLevel User No Functions Voice Keypads Keypad CommandsKeypad Functions Function DescriptionMeaning Various System Trouble DisplaysAlpha Display Keys Displayed as ZoneChecking Transmitter Enrollment Sniffer Mode Testing the SystemAbout Test Procedures System TestDialer Communication Test and Periodic Test Reports Go/No Go Test ModeAutomatic Standby Battery Tests Automatic Periodic Test ReportPhone Modules Specifications & AccessoriesRelay Module Long Range RadioCompatible 5800 Series Transmitters Table Series Transmitter Input Loop IdentificationModel Product Input Type Description 5827 Wireless Keypad Can be used to turn the burglary protection on and offInstallation Instructions Industry Canada Industrie CanadaFederal Communications Commission FCC Part FCC PartUL Notices SIA Quick Reference GuideLimitations and Warranty Limitations of this Alarm System10-2 Index 10-4 Summary of Connections Limited Warranty K0735V3 10/04 Rev. B