Bosch Appliances D7412GV3 On-Board Points, Terminals 11 to 22 Description, Point Sensor Loops

Page 31

D9412GV3/D7412GV3 Operation and Installation Guide

8.0

On-Board Points

 

 

 

7.11.3Installing the D928 Mounting

Mount the D928 on the lower right side of the enclosure using the screws provided with the switcher.

Wiring

The D928 has two flying leads. The green lead monitors AC power. The black lead is the ground reference for the AC Power LED.

1.Connect the green lead from the D928 to Terminal 1.

2.Connect the black lead from the D928 to Terminal 9.

Telephone Connections

1.Plug one end of the ribbon cable provided into J4 on the D928. Plug the other end of the ribbon cable into the ACCESSORY connector on the control panel.

2.Plug one end of the D162 phone cord provided into the telco jack. Plug the other end of the phone cord into the TELCO jack on the control panel. Refer to Table 8 for phone cord lengths.

Table 8: Phone Cord Lengths

 

 

Phone Cord

Length

D161

2.4 m (8 ft)

D162

61 cm (2 ft)

3.Plug one end of a D161 or D162 phone cord into J1 on the control panel. Plug the other end of the phone cord into the RJ31X or RJ138X for the primary telephone line.

4.Plug one end of a D161 or D162 phone cord into J2 on the control panel. Plug the other end of the phone cord into the RJ31X or RJ138X for the secondary telephone line. Refer Table 8 for phone cord lengths.

7.11.4 D928 Status LEDs

Four LEDs mounted on the front edge of the D928 Module show the status of AC power for the control panel, the status of the two telephone lines, and communication failure (Figure 11 on page 34). When programmed and operating normally, only the green AC power status LED is lit.

AC Power LED

The green AC Power Status LED lights when AC power is applied to Terminals 1 and 2 on the control panel.

Phone Line Fail LEDs

Two yellow Phone Line Status LEDs (one for the primary telephone line, one for the secondary telephone line) light if the telephone line is not within the operating range. The control panel monitors the faulty telephone line for the programmed interval before indicating a trouble condition. Refer to Section

7.8Telephone Line Monitor on page 29 for a description of phone line monitor operation.

Communication Failure LED

The yellow Communication Failure LED lights when the system is in communication failure. The LED turns off when communication restores. Refer to Section 7.10 Communication Failure on page 29.

Dedicated telephone lines might be required for UL 864 Commercial Fire applications. Check with your Authority Having Jurisdiction (AHJ).

8.0On-Board Points

8.1Terminals 11 to 22 Description

The control panel provides eight on-board points. Each point functions independently and does not interfere with the operation of the others. The control panel monitors the sensor loops for normal, shorted, or open conditions between an input terminal (11, 13, 14, 16, 17, 19, 20, or 22) and any of the point common terminals (12, 15, 18, and 21). The programming for the point determines how the control panel responds to those conditions. Refer to the D9412GV3/D7412GV3 Program Entry Guide

(P/N: F01U170807) for point programming options. The control panel also monitors the sensor loops for ground fault conditions if S4 is latched (ground fault detect enabled).

8.2Point Sensor Loops

Not for use in Fire Applications.

When wiring the on-board points (Figure 13), install a 1 kΩ resistor at the far end of the sensor loop to provide a reference for supervision. Dry-contact sensing devices can be connected in series (normally-closed) or in parallel (normally-open) to any of these loops.

The number of normally-open and normally-closed detection devices each sensor loop can supervise is limited only by the resistance on the loop. The total resistance for the wire length and contacts, minus the end-of-line (EOL) resistor, must not exceed 100 Ω.

Bosch Security Systems, Inc. 10/10 F01U143070-03

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents D9412GV3/D7412GV3 Federal Communications Commission FCC Rules TrademarksCertifications and Approvals Listings and ApprovalsFCC Registration Number Service Center in USARinger Equivalence 0.0B Contents Appendix a System Wiring Diagrams, Issue a Programmer and Accessory ConnectionsAppendix B Point Address Charts Tables Related Documentation IntroductionLightning Strikes Precautions during InstallationEffects GV3 Series Control Panel Differences Configuration and PartsFeatures D9412GV3 D7412GV3 OverviewParts Available by Separate Order Parts ListAssembly Literature PackCompatible Accessories1 AccessoriesModel Title Fire Intrusion Features in the D9412GV3 and D7412GV3 Keypads KeyswitchAccess Control Ground Fault DetectionMounting Enclosure InstallationInstallation Preparation Enclosure OptionsTerminal Installing the Control PanelConnecting Earth Ground Ground Fault Detect EnableLocking the Reset Pin Enabling Ground Fault DetectionGround Fault Specifications Ground Fault Impedance SpecificationsProgramming the Control Panel Completing the InstallationService Walk Test Procedure Installing the Point Chart LabelTesting the System Service Walk TestD9412GV3/D7412GV3 Operation and Installation Guide Test a device Bosch Security Systems, Inc /10 F01U143070-03Text displays for 60 seconds D7412GV3 Service Walk Test Flow Chart Primary Power Terminals 1 Power SupplySecondary Power Terminals Non-Power-Limited Wiring Battery Charging Circuit Replacing the Battery Charging and Battery LEDsD8132 Boost Battery Backup Adding a D8132 Investigate Low Battery reports immediately IfRecharge Cycle Battery Discharge and Recharge ScheduleCharging Status and Low Battery LEDs Discharge CycleCircuit Protection Power OutputsTotal Available Power Continuous Power Output Terminals 3, 8, 24,Voltage Output at Terminals 6, 7, Programmable Power Output Terminals 6, 7,Verification and Reset Relay A  NSC current = Alarm current Required Step AvailableLocation Telephone ConnectionsRegistration NotificationTelephone Line Monitor Phone LED RedOperation Monitor LED Green Dialing FormatDescription 11 D928 Dual Phone Line SwitcherTerminals 11 to 22 Description On-Board PointsPoint Sensor Loops Point Parameters Point ParametersLoop Voltage Range Point Response Time 64 mm 1/4 Minimum distance Comm Point Zonex Bus D9412GV3 Terminals and D7412GV3 Off-Board Points5 D9412GV3/D7412GV3 Responses to Missing Point Conditions Off-Board Point ErrorsError Condition Result Additional Information D8125 and D9127 Popit ModulesConnecting the D8125 Popex to the D9412GV3 Control Panel Connecting the D8125 Popex to the D7412GV3 Control Panel Installing the D8125 Popex Module Program Record Sheet Wiring Data Expansion Loops to Popex ModulesPopit Sensor Loops Popit Module Point AssignmentsProgram Record Sheet Popit Labels D8128D OctoPOPIT ModuleD8128D OctoPOPIT Layout Requirements for Fire Initiation ApplicationsD8128D OctoPOPIT Switch Settings for D9412GV3 and D7412GV3 InstallationSetting the OctoPOPIT Switches Address SwitchesTerminal Strip Connections Wiring OctoPOPITsUsing the Terminal Strip Mounting OctoPOPITsConnecting D8128D OctoPOPITs to the D9412GV3 Connecting D8128D OctoPOPITs to the D7412GV3 Wiring Multiple D8128Ds Using Molex Connectors Using Molex ConnectorsOctoPOPIT Sensor Loops Testing Off-Board Points10.1 D8129 OctoRelay Off-Board RelaysD8129 OctoRelay Switch Settings Configuring the D8129 OctoRelayRelay Outputs 10.2 D811 Arm Status Relay Module Wiring ConnectionsNumber of D8128Ds Used with D8129s D811 Module Wiring to the D9412GV3 D811 Module Wiring to the D7412GV3 Keypad Terminals 29 to Keypad Address SettingsArming Devices DescriptionKeypad Connections Wire Limits for Individual DevicesExtra Power for More Keypads D9412GV3 Keypad D7412GV3 Function Wire Terminal Color11.3 D279A Independent Zone Control KeyswitchOperation Maintained Contact Silencing the Bell Momentary ContactSDI Devices Installation12.3 D9131A Parallel Printer Interface Module SDI Addresses 88 12.4 D9210B Wiegand Control Interface ModuleNetwork Interface Modules Address SettingsSupervision Programmer Access Reports Programmer and Accessory ConnectionsProgrammer Connector Installer Keypad and Local Programmers ModeAccessory connector Programming connector Accessory Connector14.1 D9412GV3 Faceplate FaceplatesD7412GV3 Faceplate 14.2 D7412GV3 FaceplateD9412GV3 Control Panel Appendix a System Wiring Diagrams, Issue aD9412GV3 D9412GV3, SDI Devices System Wiring System Wiring D7412GV3 Control Panel D7412GV3, Power Supply Side System WiringD7412GV3 D7412GV3, SDI Devices System Wiring Zonex 1 Point Address Chart Appendix B Point Address ChartsZonex 2, Points 129 to 247 D9412GV3 Only Zonex 2 Point Address ChartPower Supply SpecificationsD9412GV3/D7412GV3 Operation and Installation Guide Notes Bosch Security Systems, Inc
Related manuals
Manual 154 pages 49.97 Kb

D9412GV3, D7412GV3 specifications

The Bosch Appliances D9412GV3 is a perfect blend of functionality and innovation, designed to meet the needs of modern households. This dishwasher is part of Bosch's reputation for creating high-quality, energy-efficient home appliances. With a sleek design and advanced technology, the D9412GV3 stands out in the crowded market of dishwashers.

One of the main features of the D9412GV3 is its remarkable efficiency. With an Energy Star rating, this model is designed to minimize water and energy consumption while still delivering exceptional cleaning performance. The EcoSense technology optimizes water usage, ensuring every wash cycle is both effective and economical, making it a responsible choice for energy-conscious consumers.

The dishwasher offers a spacious interior, capable of accommodating large loads. Its flexible rack system includes adjustable tines and folding platforms, making it easy to fit various dish sizes, from pots and pans to delicate glassware. Additionally, the third rack feature provides extra space for utensils and smaller items, enhancing its capacity and versatility.

In terms of cleaning power, the D9412GV3 is equipped with the PrecisionWash system. This cutting-edge technology features intelligent sensors that continuously scan and check the load, adjusting the wash cycle as needed for optimal results. Coupled with the 40 dBA noise level, it ensures that the dishwasher operates quietly in the background, so you can enjoy your home without disruptive sounds.

Another standout characteristic is the PureDry technology, an integrated drying system that uses a condensation process to gently dry dishes without the need for extra heat. This not only protects sensitive items but also saves energy, further enhancing the appliance's eco-friendly nature.

Ease of use is a priority for Bosch, as seen in the D9412GV3's user-friendly controls. The intuitive interface allows for selecting various wash cycles and options, including Heavy, Auto, and Quick options, catering to different cleaning needs. Additionally, the Time Delay feature provides the flexibility to set the dishwasher to run at a later time, great for aligning with your schedule.

In summary, the Bosch D9412GV3 combines innovative technologies with a user-centered design to deliver a top-tier dishwasher experience. Its energy-efficient operation, spacious interior, and advanced cleaning features make it an excellent choice for any kitchen, ensuring spotless dishes with minimal effort. With Bosch's commitment to quality, the D9412GV3 stands as a reliable and stylish addition to any modern home.
Top Page Image Contents