D9412GV3/D7412GV3 Operation and Installation Guide Contents
8.5Wiring Information for Installations Using the
| Rothenbuhler |
|
| Bell | 33 |
9.0 | 36 |
9.1Point (Zonex) Bus: D9412GV3 Terminals and
| D7412GV3 Terminals | 36 |
9.1.1 | POPIT Modules | 36 |
9.1.2 | POPEX Modules | 36 |
9.1.3 | Missing Conditions | 36 |
9.1.4 | Extra Point Events | 36 |
9.1.5D9412GV3/D7412GV3 Responses to Missing
| Point Conditions | 37 |
9.2 | D8125 and D9127 POPIT Modules | 37 |
9.3 | Installing the D8125 POPEX Module | 40 |
9.3.1 | Mounting | 40 |
9.3.2 | Wiring the D8125 to the Control Panel | 40 |
9.3.3Wiring POPITs to the Data Expansion Loop40
9.3.4Wiring Data Expansion Loops to POPEX
| Modules | 41 |
9.3.5 | POPIT Sensor Loops | 41 |
9.3.6 | POPIT Module Point Assignments | 41 |
9.3.7 | Program Record Sheet | 41 |
9.3.8 | POPIT Labels | 42 |
9.4 | D8128D OctoPOPIT Module | 42 |
9.4.1 | Description | 42 |
9.4.2 | Listings | 43 |
9.4.3 | Installation | 44 |
9.4.4 | Setting the OctoPOPIT Switches | 44 |
9.4.5 | Mounting OctoPOPITs | 45 |
9.4.6 | Wiring OctoPOPITs | 45 |
9.4.7 | OctoPOPIT Sensor Loops | 49 |
9.5 | Testing | 49 |
10.0 | 50 | |
10.1 | D8129 OctoRelay | 50 |
10.1.1 | Configuring the D8129 OctoRelay | 51 |
10.1.2 | Relay Outputs | 51 |
10.1.3 | Installation | 51 |
10.1.4 | Wiring Connections | 52 |
10.2 | D811 Arm Status Relay Module | 52 |
10.2.1 | Relay Output | 52 |
10.2.2 | Installation | 52 |
10.2.3 | Wiring Connections | 53 |
11.0 Arming Devices | 55 | |
11.1 | Description | 55 |
11.2 | Keypad Terminals 29 to 32 | 55 |
11.2.1 | Assigning an Address for the Keypad | 55 |
11.2.2 | Installation | 56 |
11.3 | D279A Independent Zone Control | 57 |
11.4 | Keyswitch | 57 |
11.4.1 | Description | 57 |
11.4.2 | Programming | 57 |
11.4.3 | Installation | 57 |
11.4.4 | Operation | 57 |
12.0 SDI Devices | 59 | |
12.1 | Description | 59 |
12.2 | Installation | 59 |
12.3 | D9131A Parallel Printer Interface Module ... | 59 |
12.3.1 | Switch Settings | 59 |
12.3.2 | Supervision | 59 |
12.4D9210B Wiegand Control Interface Module 60
12.4.1 | Access | 60 |
12.4.2 | Switch Settings | 60 |
12.5 | SDI Addresses 88 and 92 | 60 |
12.5.1 | D9133DC Direct Connect Programming |
|
| Module | 60 |
12.5.2 | Network Interface Modules | 61 |
12.5.3 | Address Settings | 61 |
12.5.4 | Supervision | 61 |
13.0 Programmer and Accessory Connections... | 62 | |
13.1 | Programmer Connector | 62 |
13.2Installer Keypad and Local Programmers
| Mode | 62 |
13.3 | Programmer Access Reports | 62 |
13.4 | Accessory Connector | 63 |
14.0 Faceplates | 64 | |
14.1 | D9412GV3 Faceplate | 64 |
14.2 | D7412GV3 Faceplate | 65 |
Appendix A: System Wiring Diagrams, Issue A .. | 66 | |
A.1 | D9412GV3 Control Panel | 66 |
A.2 | D7412GV3 Control Panel | 69 |
Appendix B: Point Address Charts | 72 | |
B.1 | Zonex 1, Points 9 to 127 (D9412GV3); Zonex | |
| 1, Points 9 to 75 (D7412GV3) | 72 |
B.2 | Zonex 2, Points 129 to 247 (D9412GV3 Only) | |
| ........................................................................... | 73 |
Specifications | 74 | |
SDI Bus A (+): | 74 | |
Connection: | 74 | |
Two Telco lines: | 74 | |
Discharge Cycle | 74 |
Bosch Security Systems, Inc. 10/10 | 5 |