Bosch Appliances D7412GV3 manual D811 Module Wiring to the D9412GV3

Page 53

D9412GV3/D7412GV3 Operation and Installation Guide 10.0 Off-Board Relays

Use the D137 Mounting Bracket or D9002 Mounting Skirt to install D811 Modules in enclosures with no available module mounting locations.

10.2.3 Wiring Connections

Power down the control panel to connect D811 Modules as shown in Figure 26 on this page and Figure 27 on page 54.

The D811 for Relay 53 connects to

Zonex 1.

The D811 for Relay 117 connects to

Zonex 2 on the D9412GV3.

Figure 26: D811 Module Wiring to the D9412GV3

1 -	D811 for Relay 53	3- On-board points
2-	D811 for Relay 117

Bosch Security Systems, Inc. 10/10 F01U143070-03

53

Image 53

Contents D9412GV3/D7412GV3 Certifications and Approvals TrademarksListings and Approvals Federal Communications Commission FCC RulesRinger Equivalence 0.0B Service Center in USAFCC Registration Number Contents Appendix B Point Address Charts Programmer and Accessory ConnectionsAppendix a System Wiring Diagrams, Issue a Tables Related Documentation IntroductionEffects Precautions during InstallationLightning Strikes Features D9412GV3 D7412GV3 Configuration and PartsOverview GV3 Series Control Panel DifferencesAssembly Parts ListLiterature Pack Parts Available by Separate OrderModel Title Fire Intrusion AccessoriesCompatible Accessories1 Features in the D9412GV3 and D7412GV3 Access Control KeyswitchGround Fault Detection KeypadsInstallation Preparation InstallationEnclosure Options Mounting EnclosureConnecting Earth Ground Installing the Control PanelGround Fault Detect Enable TerminalGround Fault Specifications Enabling Ground Fault DetectionGround Fault Impedance Specifications Locking the Reset PinProgramming the Control Panel Completing the InstallationTesting the System Installing the Point Chart LabelService Walk Test Service Walk Test ProcedureD9412GV3/D7412GV3 Operation and Installation Guide Text displays for 60 seconds Bosch Security Systems, Inc /10 F01U143070-03Test a device D7412GV3 Service Walk Test Flow Chart Secondary Power Terminals Power SupplyPrimary Power Terminals 1 Non-Power-Limited Wiring D8132 Boost Battery Backup Adding a D8132 Replacing the Battery Charging and Battery LEDsInvestigate Low Battery reports immediately If Battery Charging CircuitCharging Status and Low Battery LEDs Battery Discharge and Recharge ScheduleDischarge Cycle Recharge CycleTotal Available Power Power OutputsContinuous Power Output Terminals 3, 8, 24, Circuit ProtectionVerification and Reset Relay Programmable Power Output Terminals 6, 7,A  NSC current = Alarm current Required Step Available Voltage Output at Terminals 6, 7,Registration Telephone ConnectionsNotification LocationOperation Monitor LED Green Phone LED RedDialing Format Telephone Line MonitorDescription 11 D928 Dual Phone Line SwitcherPoint Sensor Loops On-Board PointsTerminals 11 to 22 Description Loop Voltage Range Point ParametersPoint Parameters Point Response Time 64 mm 1/4 Minimum distance Comm Point Zonex Bus D9412GV3 Terminals and D7412GV3 Off-Board PointsError Condition Result Additional Information Off-Board Point ErrorsD8125 and D9127 Popit Modules 5 D9412GV3/D7412GV3 Responses to Missing Point ConditionsConnecting the D8125 Popex to the D9412GV3 Control Panel Connecting the D8125 Popex to the D7412GV3 Control Panel Installing the D8125 Popex Module Popit Sensor Loops Wiring Data Expansion Loops to Popex ModulesPopit Module Point Assignments Program Record SheetProgram Record Sheet Popit Labels D8128D OctoPOPIT ModuleD8128D OctoPOPIT Layout Requirements for Fire Initiation ApplicationsSetting the OctoPOPIT Switches InstallationAddress Switches D8128D OctoPOPIT Switch Settings for D9412GV3 and D7412GV3Using the Terminal Strip Wiring OctoPOPITsMounting OctoPOPITs Terminal Strip ConnectionsConnecting D8128D OctoPOPITs to the D9412GV3 Connecting D8128D OctoPOPITs to the D7412GV3 Wiring Multiple D8128Ds Using Molex Connectors Using Molex ConnectorsOctoPOPIT Sensor Loops Testing Off-Board Points 10.1 D8129 OctoRelay Off-Board RelaysRelay Outputs Configuring the D8129 OctoRelayD8129 OctoRelay Switch Settings Number of D8128Ds Used with D8129s Wiring Connections10.2 D811 Arm Status Relay Module D811 Module Wiring to the D9412GV3 D811 Module Wiring to the D7412GV3 Arming Devices Keypad Address SettingsDescription Keypad Terminals 29 toExtra Power for More Keypads Wire Limits for Individual DevicesD9412GV3 Keypad D7412GV3 Function Wire Terminal Color Keypad ConnectionsOperation Maintained Contact Keyswitch11.3 D279A Independent Zone Control Silencing the Bell Momentary Contact12.3 D9131A Parallel Printer Interface Module InstallationSDI Devices SDI Addresses 88 12.4 D9210B Wiegand Control Interface ModuleSupervision Address SettingsNetwork Interface Modules Programmer Connector Programmer and Accessory ConnectionsInstaller Keypad and Local Programmers Mode Programmer Access ReportsAccessory connector Programming connector Accessory Connector14.1 D9412GV3 Faceplate FaceplatesD7412GV3 Faceplate 14.2 D7412GV3 FaceplateD9412GV3 Control Panel Appendix a System Wiring Diagrams, Issue aD9412GV3 D9412GV3, SDI Devices System Wiring System Wiring D7412GV3 Control Panel D7412GV3, Power Supply Side System WiringD7412GV3 D7412GV3, SDI Devices System Wiring Zonex 1 Point Address Chart Appendix B Point Address ChartsZonex 2, Points 129 to 247 D9412GV3 Only Zonex 2 Point Address ChartPower Supply SpecificationsD9412GV3/D7412GV3 Operation and Installation Guide Notes Bosch Security Systems, Inc

Related manuals

Manual 154 pages 49.97 Kb