Linear DVS-2400 manual External Console Speaker Connection, External Alarm Siren Connection

Page 11
EXTERNAL CONSOLE SPEAKER CONNECTION

EXTERNAL CONSOLE SPEAKER CONNECTION

An external console speaker sounds system tones

and alerts occupants with a loud siren during alarm.

With the VB-2 module installed, the Central Station

can talk to the occupants through the external

console speaker.

EXTERNAL CONSOLE SPEAKER

Use an 8-ohm, 10 watt minimum rated speaker. Do

not use a horn/siren with a built-in siren driver.

Up to two 8-ohm speakers can be used with each

Console.

Up to 150 feet of 22 AWG wire can be used with

each speaker.

The system tone volume can be adjusted with the

annunciator volume control.

 

LINEAR SECURITY CONSOLE MODEL DVS-2400

 

ANNUNCIATOR

 

VOLUME

MAIN

CONTROL

 

TERMINAL

 

BLOCK

OPTIONAL

 

VOICE MODULE

 

MODEL: VB-2

MAIN TERMINAL BLOCK

 

AC

 

AC

EXT. SPKR(S)

EXT. SPKR

8 OHM/10 WATT

(-)

2 SPKRS MAX.

H/A -

NOTE: REMOVE

H/A +

JUMPER FOR

RELAY N.O.

EXT. SPEAKERS

RELAY DRY

 

1.

Mount the external speaker.

2.

Route the speaker wires from the external speaker

 

to the Console.

3.

Open the Console top cover and locate the main

 

terminal block.

4.

Route the speaker wires up through the wiring

 

access hole.

5.

Remove the wire jumper from the EXT. SPKR & (-)

 

terminals.

6.

Connect the speaker wires to the EXT. SPKR & (-)

EXTERNAL

CONSOLE

SPEAKER

8 OHM, 10 WATT

MINIMUM

REMOVE

terminals.

NOTE: If connecting two external speakers, connect the second speaker in parallel, to the same EXT. SPKR & (-) terminals as the first speaker.

EXTERNAL ALARM SIREN CONNECTION

An external siren alerts occupants and neighbors

with a loud siren during alarm.

Use a 12 volt, 1 amp maximum rated weather-

resistant horn speaker with a built-in siren driver. Do

JUMPER

CONNECT SPEAKER LEADS TO EXT. SPKR & (-) TERMINALS

EXTERNAL

ALARM

SIREN

not use a plain speaker.

NOTE: Connection of an electromechanical bell or motor bell is not recommended because of the radio interference generated when the bell is running.

UL NOTE: Not for use in UL installations.

1.

Mount the external siren.

2.

Route the wires from the external siren to the

 

Console.

3.

Open the Console top cover and locate the main

 

terminal strip.

4.

Route the siren wires up through the wiring access

 

hole.

 

LINEAR SECURITY CONSOLE MODEL DVS-2400

MAIN

 

TERMINAL

 

BLOCK

OPTIONAL

 

VOICE MODULE

 

MODEL: VB-2

MAIN TERMINAL BLOCK

 

AC

 

AC

EXTERNAL SIREN

EXT. SPKR

(-)

12 VDC 1 AMP

H/A -

MAXIMUM

 

H/A +

 

RELAY N.O.

 

RELAY DRY

5. Connect the siren wires to the RELAY N.O. & (-)

terminals.

NOTE: By removing the Console’s auxiliary fuse, the relay contacts will become isolated. Use the RELAY N.O. & RELAY DRY terminals to switch an externally powered load.

EXTERNAL

ALARM RELAY 12 VDC 1 AMP MAXIMUM

CONNECT SIREN LEADS TO (-) & RELAY N.O. TERMINALS

9

Image 11
Contents USA & Canada SUPERVISED WIRELESS SECURITY CONSOLEInstallation & Programming Instructions SECURITYINTRODUCTION This symbol is for important notesTABLE OF CONTENTS CONSOLE 1.THE DVS-2400SECURITY SYSTEMSMOKE DETECTOR WIRELESS KEYPADREMOTE CONTROLS DOOR/WINDOW SENSORSExample Residential Security System Floor Plan DESIGN THE INSTALLATION2.SECURITY SYSTEM FLOOR PLAN EXAMPLE SYSTEMWIRELESS KEYPAD 3.TYPICAL SYSTEM SENSORSDOOR/WINDOW SENSOR ABOUT SENSOR STATUS SUPERVISIONSwitching to Chime Mode stops the alarm siren 4.CONSOLE FEATURES5 4 3 Switching to Off Mode stops the alarm sirenType 2AG, 1-ampfuse WALL MOUNTING 5.CONSOLE INSTALLATIONCONSOLE LOCATION CASE LOCKING SCREWcan talk to the occupants through the external EXTERNAL CONSOLE SPEAKER CONNECTIONEXTERNAL ALARM SIREN CONNECTION Connect the Console to the telephone line if the TELEPHONE LINE CONNECTIONAUTOMATION OUTPUT CONNECTION OPTIONAL complete CONSOLE POWER CONNECTIONnot plug the transformer in until the wiring is BACKUP BATTERY INSTALLATION OPTIONALMASTER USER CODE 1 GONG & 5 BEEPS indicator for that sensor will stay lit6.BASIC CONSOLE PROGRAMMING START IN TESTFor DXT-61, DXT-21, DXS-21, DXT-41,& DXS-62A PROGRAMMING DIFFERENT SENSOR TYPESFollow the instructions on the previous page to select a sensor number to program the sensor intoDXS-10WIRELESS KEYPAD 7.BASIC SENSOR INSTALLATION4.Snap sensor onto mounting plate DXS-31& DXS-32DOOR/WINDOW SENSORSTEST SENSORS LABELING THE SENSORS 8.CUSTOMIZING THE CONSOLEOFF MODE and stops any alarms in progresscaused the alarm will fl ash 9.CONSOLE OPERATING MODESSTART IN HOME MODE HOME MODESECURE EXIT START IN OFF OR CHIME MODESTART HERE HOLD AWAY MODEQUICK ARM OPTIONAL YOUR USER CODE 1 GONG & 3 BEEPSSTART IN OFF 3 beeps being the strongest signalstatus indicators TEST MODESENSOR RADIO TROUBLE CONSOLE LOW BATTERY10.SYSTEM TROUBLE INDICATIONS SENSOR LOW BATTERIESMASTER USER CODE 1 GONG & 5 BEEPS SENSOR and the sensor status indicator will turn off11.CUSTOMIZING THE SYSTEM ACTIVATE SENSOR DONE START IN TEST7 FOR 7 PRS INTERIOR ZONE AWAY 1 BING DONE SENSOR NUMBER FOR CHIME8 FOR 8 TUV CHIME ZONE AWAY 1 BING DONE SENSOR NUMBER FOR INTERIORAWAY SENSOR NUMBER FOR FUNCTION CHANGENEW FUNCTION NUMBER FOR SENSOR AWAY 1 BING DONE MAKING A SENSOR PERFORM A DIFFERENT FUNCTIONTEST = REMOVE SETUP MODE12.ADVANCED PROGRAMMING HOME = PROGRAMEXIT DELAY TIME CHANGING A SENSORS RESTORE REQUIREMENTSCHANGING A SENSORS SUPERVISION ENTRY DELAY TIMEAUTOMATION OUTPUT TIME REMOTE CONTROL ARMING LEVELREMOTE CONTROL DISARMING LEVEL FIRE SIREN TIMEAUTOMATIC RESTORAL OF BYPASSED SENSORS SILENT BURGLARY ALARMSSILENT EMERGENCY ALARMS DISABLING QUICK ARMINGAUTOMATION OUTPUT ON DURING ALARM AUTOMATION OUTPUT MODE DURING ALARMREMOTE CONTROL ARM/DISARM CHIRP AUTOMATION OUTPUT ON DURING AND AFTER ALARMAUTOMATION OUTPUT POLARITY REMOTE ACCESS PASSWORDAUTOMATION OUTPUT WHILE ARMED AUTOMATION OUTPUT DURING EXIT/ENTRY DELAYSCONSOLE MASTER RESET Because access to programming would be impossibleusing these steps. The master user code can be changed using programming STEP #99SETUP MODE SETUP MODE13.COMMUNICATOR PROGRAMMING General Communicator Programming TableVOICE RESPONSE COMMUNICATOR ENABLEGENERAL COMMUNICATOR OPTIONS 2-WAYAUDIO0PROGRAMMING STEP #101 CALL LIMITERDIALING DELAY DIALING METHODCommunicator Reporting Option Table COMMUNICATOR REPORTING OPTIONSREPORTING FORMAT CALL ROUTINGSUPERVISORY OR PAGER TELEPHONE NUMBER ACCOUNT NUMBERPRIMARY TELEPHONE NUMBER SECONDARY TELEPHONE NUMBERPOINT ID REPORTING REPORT CONSOLE TROUBLEREPORT FORCE ARMING OPENING AND CLOSING REPORTSGeneral Reporting Codes Table COMMUNICATOR REPORTING CODESGENERAL REPORTING CODES STEPS #201-206DURESS REPORTING CODE SYSTEM REPORTING CODESSTEPS #261-266 FORCE ARMING REPORTING CODE4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES 4 BY 2 FORMAT POINT ID ALARM REPORT CODES4 BY 2 FORMAT POINT ID REPORTING CODES STEPS #210-233PROGRAMMING FUNCTION 4 by 2 Format Point ID Reporting Code Table4 BY 2 FORMAT POINT ID REPORTING CODES STEP #FCC NOTICE LINEAR LIMITED WARRANTYWIRELESS PRODUCT NOTICE 14. IMPORTANT INFORMATION
Related manuals
Manual 48 pages 58.1 Kb

DVS-2400 specifications

The Linear DVS-1200, DVS-2400, RA-2400, DUAL-824, and DVS-2408 are advanced digital video surveillance systems designed for a variety of security applications. These models offer state-of-the-art features, technologies, and characteristics that enhance security monitoring and recording capabilities.

The DVS-1200 is a compact and efficient digital video recorder that supports up to 12 channels of video input. It features high-resolution recording capabilities, providing clear and detailed images. With real-time playback and advanced motion detection, the DVS-1200 allows users to monitor activities effectively. Its user-friendly interface simplifies configuration and operation, making it accessible for both novice and experienced users.

Upgraded for larger installations, the DVS-2400 supports up to 24 channels. This model is equipped with H.264 video compression technology, significantly reducing storage requirements while maintaining high-quality images. The DVS-2400 also offers remote access capabilities, enabling users to view live footage or playback recorded events from anywhere using a smartphone or computer. Its built-in analytics features allow for motion detection, line crossing alerts, and more, enhancing overall security.

The RA-2400 is a remarkable model designed for robust performance in demanding environments. This recorder not only supports 24 channels but also integrates advanced RAID technology for data redundancy and enhanced storage reliability. The RA-2400 is ideal for applications where data loss is unacceptable, making it suitable for critical infrastructure and high-security locations.

The DUAL-824 model stands out with its unique dual-stream encoding feature. It allows simultaneous recording and streaming of two video resolutions, providing flexibility for different applications such as local monitoring and remote access. This model supports up to 8 channels and is equipped with advanced event triggers, ensuring significant activities do not go unnoticed.

Finally, the DVS-2408 is a versatile and high-performance system designed for larger facilities. With support for 24 channels and the ability to integrate with various IP cameras, the DVS-2408 delivers exceptional scalability. This model comes with comprehensive software for monitoring and management, allowing for multiple users and custom user permissions.

Together, these Linear video surveillance models represent a robust and reliable solution for modern security needs, featuring the latest technologies and high-quality performance to ensure safety and peace of mind in various environments.