Linear DVS-2400 manual Basic Sensor Installation, DXS-10WIRELESS KEYPAD

Page 16
7.BASIC SENSOR INSTALLATION

7.BASIC SENSOR INSTALLATION

Each accessory sensor is packaged with its own set of installation instructions specifi c to the model of sensor.

Refer to the sensor's instructions for details on installing, operating, and testing of the sensor.

Following are basic instructions for installing two popular DVS-2400 accessories: The Model DXS-10 Wireless Remote Keypad and the Model DXS-31 or DXS-32 Door/Window Transmitters.

DXS-10 WIRELESS KEYPAD

The DXS-10 is used to remotely command the Console.

The keypad can be simply set on a table or mounted to a fl at surface.

TABLE-TOP USE

Four anti-mar pads are provided as a scratch deterrent “feet” for the keypad.

NOTE: Do not use the adhesive “feet” if the keypad is going to be wall mounted.

1.Peel off the adhesive tape backing on the pads and stick them to the back of the keypad.

The wireless keypad can be used as a portable keypad. Because of the hourly supervisory transmissions, if the unit is taken out of range from the Console for more than eight hours, the Console will indicate “radio trouble” for the keypad. The keypad's sensor number can be programmed for “non-supervised” if required. See the “Advanced Programming” section of this manual.

WALL MOUNT USE

The wireless keypad can be wall mounted in a convenient location.

1.Open the keypad by inserting a small screwdriver in one of the top slots in the keypad case. Gently twist the screwdriver until the case pops open.

2.Attach the rear case to the wall using the two screws provided.

NOTE: For best signal transmission, the keypad should be mounted at least three feet above ground level.

3.Hook the top edge of the keypad case together and snap the keypad onto the rear case.

WARNING: The wireless keypad is designed for indoor use only.

FROM TOP OF CASE TWIST

SCREWDRIVER BETWEEN

CASE HALVES UNTIL IT

POPS OPEN

CONNECT BATTERY

TO BATTERY CLIPS

USE THE FOUR SCRATCH

DETERRENT PADS PROVIDED

FOR TABLE-TOP USE

ATTACH REAR CASE TO WALL

WITH THE TWO SCREWS PROVIDED

MOUNT AT A CONVENIENT

LOCATION NEAR PRIMARY

ENTRY/EXIT DOOR

14

Image 16
Contents SUPERVISED WIRELESS SECURITY CONSOLE Installation & Programming InstructionsSECURITY USA & CanadaThis symbol is for important notes INTRODUCTIONTABLE OF CONTENTS 1.THE DVS-2400SECURITY SYSTEM CONSOLEWIRELESS KEYPAD REMOTE CONTROLSDOOR/WINDOW SENSORS SMOKE DETECTORDESIGN THE INSTALLATION 2.SECURITY SYSTEM FLOOR PLANEXAMPLE SYSTEM Example Residential Security System Floor Plan3.TYPICAL SYSTEM SENSORS DOOR/WINDOW SENSORABOUT SENSOR STATUS SUPERVISION WIRELESS KEYPAD4.CONSOLE FEATURES 5 4 3Switching to Off Mode stops the alarm siren Switching to Chime Mode stops the alarm sirenType 2AG, 1-ampfuse 5.CONSOLE INSTALLATION CONSOLE LOCATIONCASE LOCKING SCREW WALL MOUNTINGEXTERNAL ALARM SIREN CONNECTION EXTERNAL CONSOLE SPEAKER CONNECTIONcan talk to the occupants through the external AUTOMATION OUTPUT CONNECTION OPTIONAL TELEPHONE LINE CONNECTIONConnect the Console to the telephone line if the CONSOLE POWER CONNECTION not plug the transformer in until the wiring isBACKUP BATTERY INSTALLATION OPTIONAL completeindicator for that sensor will stay lit 6.BASIC CONSOLE PROGRAMMINGSTART IN TEST MASTER USER CODE 1 GONG & 5 BEEPSPROGRAMMING DIFFERENT SENSOR TYPES Follow the instructions on the previous page toselect a sensor number to program the sensor into For DXT-61, DXT-21, DXS-21, DXT-41,& DXS-62A7.BASIC SENSOR INSTALLATION DXS-10WIRELESS KEYPADTEST SENSORS DXS-31& DXS-32DOOR/WINDOW SENSORS4.Snap sensor onto mounting plate 8.CUSTOMIZING THE CONSOLE LABELING THE SENSORSand stops any alarms in progress caused the alarm will fl ash9.CONSOLE OPERATING MODES OFF MODEHOME MODE SECURE EXITSTART IN OFF OR CHIME MODE START IN HOME MODEAWAY MODE QUICK ARMOPTIONAL YOUR USER CODE 1 GONG & 3 BEEPS START HERE HOLD3 beeps being the strongest signal status indicatorsTEST MODE START IN OFFCONSOLE LOW BATTERY 10.SYSTEM TROUBLE INDICATIONSSENSOR LOW BATTERIES SENSOR RADIO TROUBLEand the sensor status indicator will turn off 11.CUSTOMIZING THE SYSTEMACTIVATE SENSOR DONE START IN TEST MASTER USER CODE 1 GONG & 5 BEEPS SENSORSENSOR NUMBER FOR CHIME 8 FOR 8 TUV CHIME ZONE AWAY 1 BING DONESENSOR NUMBER FOR INTERIOR 7 FOR 7 PRS INTERIOR ZONE AWAY 1 BING DONESENSOR NUMBER FOR FUNCTION CHANGE NEW FUNCTION NUMBER FOR SENSOR AWAY 1 BING DONEMAKING A SENSOR PERFORM A DIFFERENT FUNCTION AWAYSETUP MODE 12.ADVANCED PROGRAMMINGHOME = PROGRAM TEST = REMOVECHANGING A SENSORS RESTORE REQUIREMENTS CHANGING A SENSORS SUPERVISIONENTRY DELAY TIME EXIT DELAY TIMEREMOTE CONTROL ARMING LEVEL REMOTE CONTROL DISARMING LEVELFIRE SIREN TIME AUTOMATION OUTPUT TIMESILENT BURGLARY ALARMS SILENT EMERGENCY ALARMSDISABLING QUICK ARMING AUTOMATIC RESTORAL OF BYPASSED SENSORSAUTOMATION OUTPUT MODE DURING ALARM REMOTE CONTROL ARM/DISARM CHIRPAUTOMATION OUTPUT ON DURING AND AFTER ALARM AUTOMATION OUTPUT ON DURING ALARMREMOTE ACCESS PASSWORD AUTOMATION OUTPUT WHILE ARMEDAUTOMATION OUTPUT DURING EXIT/ENTRY DELAYS AUTOMATION OUTPUT POLARITYBecause access to programming would be impossible using these steps. The master user code can bechanged using programming STEP #99 CONSOLE MASTER RESETSETUP MODE 13.COMMUNICATOR PROGRAMMINGGeneral Communicator Programming Table SETUP MODECOMMUNICATOR ENABLE GENERAL COMMUNICATOR OPTIONS2-WAYAUDIO VOICE RESPONSECALL LIMITER DIALING DELAYDIALING METHOD 0PROGRAMMING STEP #101COMMUNICATOR REPORTING OPTIONS REPORTING FORMATCALL ROUTING Communicator Reporting Option TableACCOUNT NUMBER PRIMARY TELEPHONE NUMBERSECONDARY TELEPHONE NUMBER SUPERVISORY OR PAGER TELEPHONE NUMBERREPORT CONSOLE TROUBLE REPORT FORCE ARMINGOPENING AND CLOSING REPORTS POINT ID REPORTINGCOMMUNICATOR REPORTING CODES GENERAL REPORTING CODESSTEPS #201-206 General Reporting Codes TableSYSTEM REPORTING CODES STEPS #261-266FORCE ARMING REPORTING CODE DURESS REPORTING CODE4 BY 2 FORMAT POINT ID ALARM REPORT CODES 4 BY 2 FORMAT POINT ID REPORTING CODESSTEPS #210-233 4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES4 by 2 Format Point ID Reporting Code Table 4 BY 2 FORMAT POINT ID REPORTING CODESSTEP # PROGRAMMING FUNCTIONLINEAR LIMITED WARRANTY WIRELESS PRODUCT NOTICE14. IMPORTANT INFORMATION FCC NOTICE
Related manuals
Manual 48 pages 58.1 Kb

DVS-2400 specifications

The Linear DVS-1200, DVS-2400, RA-2400, DUAL-824, and DVS-2408 are advanced digital video surveillance systems designed for a variety of security applications. These models offer state-of-the-art features, technologies, and characteristics that enhance security monitoring and recording capabilities.

The DVS-1200 is a compact and efficient digital video recorder that supports up to 12 channels of video input. It features high-resolution recording capabilities, providing clear and detailed images. With real-time playback and advanced motion detection, the DVS-1200 allows users to monitor activities effectively. Its user-friendly interface simplifies configuration and operation, making it accessible for both novice and experienced users.

Upgraded for larger installations, the DVS-2400 supports up to 24 channels. This model is equipped with H.264 video compression technology, significantly reducing storage requirements while maintaining high-quality images. The DVS-2400 also offers remote access capabilities, enabling users to view live footage or playback recorded events from anywhere using a smartphone or computer. Its built-in analytics features allow for motion detection, line crossing alerts, and more, enhancing overall security.

The RA-2400 is a remarkable model designed for robust performance in demanding environments. This recorder not only supports 24 channels but also integrates advanced RAID technology for data redundancy and enhanced storage reliability. The RA-2400 is ideal for applications where data loss is unacceptable, making it suitable for critical infrastructure and high-security locations.

The DUAL-824 model stands out with its unique dual-stream encoding feature. It allows simultaneous recording and streaming of two video resolutions, providing flexibility for different applications such as local monitoring and remote access. This model supports up to 8 channels and is equipped with advanced event triggers, ensuring significant activities do not go unnoticed.

Finally, the DVS-2408 is a versatile and high-performance system designed for larger facilities. With support for 24 channels and the ability to integrate with various IP cameras, the DVS-2408 delivers exceptional scalability. This model comes with comprehensive software for monitoring and management, allowing for multiple users and custom user permissions.

Together, these Linear video surveillance models represent a robust and reliable solution for modern security needs, featuring the latest technologies and high-quality performance to ensure safety and peace of mind in various environments.