Linear DVS-2400 manual Silent Burglary Alarms, Silent Emergency Alarms, Disabling Quick Arming

Page 30
SILENT BURGLARY ALARMS

SILENT BURGLARY ALARMS

The factory setting causes audible burglary alarms.

STEP #63 The Console can be programmed for silent burglary alarms using this step.

6MNO

PROGRAMMING STEP #63

3DEF

HOME PROGRAM

0 FOR AUDIBLE BURG

1 FOR SILENT BURG

AWAY STORE PROGRAM

SILENT EMERGENCY ALARMS

The factory setting causes audible emergency alarms.

STEP #64 The Console can be programmed for silent emergency alarms using this step.

6MNO

PROGRAMMING STEP #64

4GHI

HOME PROGRAM

0 FOR AUDIBLE EMERGENCY

1 FOR SILENT EMERGENCY

AWAY STORE PROGRAM

DISABLING QUICK ARMING

The factory setting allows quick arming of the Console by pressing down the mode keys for two seconds.

STEP #65 The Console can be programmed to not allow quick arming using this step. If quick arming is disabled, a user code must be entered before pressing the mode buttons.

NOTE: For commercial installations with retail traffic, it is recommended to disable quick arming to prevent customers from arming the system.

NOTE: If quick arming is disabled the Home Instant Mode is unavailable.

6MNO

PROGRAMMING STEP #65

5JKL

HOME PROGRAM

0 FOR QUICK ARMING OFF

1 FOR QUICK ARMING ON

AWAY STORE PROGRAM

AUTOMATIC RESTORAL OF BYPASSED SENSORS

Bypassed sensors are ignored by the Console and cannot cause an alarm.

The factory setting causes the Console to automatically restore (remove the bypass from) sensors that close. After it's restored, the sensor is ready to cause an alarm the next time it is opened.

STEP #66 The Console can be programmed to not automatically restore any bypassed sensor when the sensor closes using this step. Bypassed sensors will then remain bypassed until the system is disarmed.

6MNO

PROGRAMMING STEP #66

6MNO

HOME PROGRAM

0 FOR AUTO RESTORAL OFF

1 FOR AUTO RESTORAL ON

AWAY STORE PROGRAM

NOTE: This setting affects all sensors.

AUTOMATIC BYPASSING OF OPEN SENSORS

The factory setting requires the user to manually bypass any open sensors when the system is armed.

If arming is attempted with open sensors, the Console will sound fi ve two-tone Beeps and will not arm.

Arming to the same mode again within fi ve seconds will bypass any open sensors and arm the Console.

STEP #67 The Console can be programmed to automatically bypass any open sensors when the system is armed using this step.

NOTE: This setting affects all sensors.

6MNO

PROGRAMMING STEP #67

7PRS

HOME PROGRAM

0 FOR AUTO BYPASS OFF

1 FOR AUTO BYPASS ON

AWAY STORE PROGRAM

28

Image 30
Contents SECURITY SUPERVISED WIRELESS SECURITY CONSOLEInstallation & Programming Instructions USA & CanadaThis symbol is for important notes INTRODUCTIONTABLE OF CONTENTS 1.THE DVS-2400SECURITY SYSTEM CONSOLEDOOR/WINDOW SENSORS WIRELESS KEYPADREMOTE CONTROLS SMOKE DETECTOREXAMPLE SYSTEM DESIGN THE INSTALLATION2.SECURITY SYSTEM FLOOR PLAN Example Residential Security System Floor PlanABOUT SENSOR STATUS SUPERVISION 3.TYPICAL SYSTEM SENSORSDOOR/WINDOW SENSOR WIRELESS KEYPADSwitching to Off Mode stops the alarm siren 4.CONSOLE FEATURES5 4 3 Switching to Chime Mode stops the alarm sirenType 2AG, 1-ampfuse CASE LOCKING SCREW 5.CONSOLE INSTALLATIONCONSOLE LOCATION WALL MOUNTINGEXTERNAL CONSOLE SPEAKER CONNECTION EXTERNAL ALARM SIREN CONNECTIONcan talk to the occupants through the external TELEPHONE LINE CONNECTION AUTOMATION OUTPUT CONNECTION OPTIONALConnect the Console to the telephone line if the BACKUP BATTERY INSTALLATION OPTIONAL CONSOLE POWER CONNECTIONnot plug the transformer in until the wiring is completeSTART IN TEST indicator for that sensor will stay lit6.BASIC CONSOLE PROGRAMMING MASTER USER CODE 1 GONG & 5 BEEPSselect a sensor number to program the sensor into PROGRAMMING DIFFERENT SENSOR TYPESFollow the instructions on the previous page to For DXT-61, DXT-21, DXS-21, DXT-41,& DXS-62A7.BASIC SENSOR INSTALLATION DXS-10WIRELESS KEYPADDXS-31& DXS-32DOOR/WINDOW SENSORS TEST SENSORS4.Snap sensor onto mounting plate 8.CUSTOMIZING THE CONSOLE LABELING THE SENSORS9.CONSOLE OPERATING MODES and stops any alarms in progresscaused the alarm will fl ash OFF MODESTART IN OFF OR CHIME MODE HOME MODESECURE EXIT START IN HOME MODEOPTIONAL YOUR USER CODE 1 GONG & 3 BEEPS AWAY MODEQUICK ARM START HERE HOLDTEST MODE 3 beeps being the strongest signalstatus indicators START IN OFFSENSOR LOW BATTERIES CONSOLE LOW BATTERY10.SYSTEM TROUBLE INDICATIONS SENSOR RADIO TROUBLEACTIVATE SENSOR DONE START IN TEST and the sensor status indicator will turn off11.CUSTOMIZING THE SYSTEM MASTER USER CODE 1 GONG & 5 BEEPS SENSORSENSOR NUMBER FOR INTERIOR SENSOR NUMBER FOR CHIME8 FOR 8 TUV CHIME ZONE AWAY 1 BING DONE 7 FOR 7 PRS INTERIOR ZONE AWAY 1 BING DONEMAKING A SENSOR PERFORM A DIFFERENT FUNCTION SENSOR NUMBER FOR FUNCTION CHANGENEW FUNCTION NUMBER FOR SENSOR AWAY 1 BING DONE AWAYHOME = PROGRAM SETUP MODE12.ADVANCED PROGRAMMING TEST = REMOVEENTRY DELAY TIME CHANGING A SENSORS RESTORE REQUIREMENTSCHANGING A SENSORS SUPERVISION EXIT DELAY TIMEFIRE SIREN TIME REMOTE CONTROL ARMING LEVELREMOTE CONTROL DISARMING LEVEL AUTOMATION OUTPUT TIMEDISABLING QUICK ARMING SILENT BURGLARY ALARMSSILENT EMERGENCY ALARMS AUTOMATIC RESTORAL OF BYPASSED SENSORSAUTOMATION OUTPUT ON DURING AND AFTER ALARM AUTOMATION OUTPUT MODE DURING ALARMREMOTE CONTROL ARM/DISARM CHIRP AUTOMATION OUTPUT ON DURING ALARMAUTOMATION OUTPUT DURING EXIT/ENTRY DELAYS REMOTE ACCESS PASSWORDAUTOMATION OUTPUT WHILE ARMED AUTOMATION OUTPUT POLARITYchanged using programming STEP #99 Because access to programming would be impossibleusing these steps. The master user code can be CONSOLE MASTER RESETGeneral Communicator Programming Table SETUP MODE13.COMMUNICATOR PROGRAMMING SETUP MODE2-WAYAUDIO COMMUNICATOR ENABLEGENERAL COMMUNICATOR OPTIONS VOICE RESPONSEDIALING METHOD CALL LIMITERDIALING DELAY 0PROGRAMMING STEP #101CALL ROUTING COMMUNICATOR REPORTING OPTIONSREPORTING FORMAT Communicator Reporting Option TableSECONDARY TELEPHONE NUMBER ACCOUNT NUMBERPRIMARY TELEPHONE NUMBER SUPERVISORY OR PAGER TELEPHONE NUMBEROPENING AND CLOSING REPORTS REPORT CONSOLE TROUBLEREPORT FORCE ARMING POINT ID REPORTINGSTEPS #201-206 COMMUNICATOR REPORTING CODESGENERAL REPORTING CODES General Reporting Codes TableFORCE ARMING REPORTING CODE SYSTEM REPORTING CODESSTEPS #261-266 DURESS REPORTING CODESTEPS #210-233 4 BY 2 FORMAT POINT ID ALARM REPORT CODES4 BY 2 FORMAT POINT ID REPORTING CODES 4 BY 2 FORMAT POINT ID TROUBLE REPORT CODESSTEP # 4 by 2 Format Point ID Reporting Code Table4 BY 2 FORMAT POINT ID REPORTING CODES PROGRAMMING FUNCTION14. IMPORTANT INFORMATION LINEAR LIMITED WARRANTYWIRELESS PRODUCT NOTICE FCC NOTICE
Related manuals
Manual 48 pages 58.1 Kb

DVS-2400 specifications

The Linear DVS-1200, DVS-2400, RA-2400, DUAL-824, and DVS-2408 are advanced digital video surveillance systems designed for a variety of security applications. These models offer state-of-the-art features, technologies, and characteristics that enhance security monitoring and recording capabilities.

The DVS-1200 is a compact and efficient digital video recorder that supports up to 12 channels of video input. It features high-resolution recording capabilities, providing clear and detailed images. With real-time playback and advanced motion detection, the DVS-1200 allows users to monitor activities effectively. Its user-friendly interface simplifies configuration and operation, making it accessible for both novice and experienced users.

Upgraded for larger installations, the DVS-2400 supports up to 24 channels. This model is equipped with H.264 video compression technology, significantly reducing storage requirements while maintaining high-quality images. The DVS-2400 also offers remote access capabilities, enabling users to view live footage or playback recorded events from anywhere using a smartphone or computer. Its built-in analytics features allow for motion detection, line crossing alerts, and more, enhancing overall security.

The RA-2400 is a remarkable model designed for robust performance in demanding environments. This recorder not only supports 24 channels but also integrates advanced RAID technology for data redundancy and enhanced storage reliability. The RA-2400 is ideal for applications where data loss is unacceptable, making it suitable for critical infrastructure and high-security locations.

The DUAL-824 model stands out with its unique dual-stream encoding feature. It allows simultaneous recording and streaming of two video resolutions, providing flexibility for different applications such as local monitoring and remote access. This model supports up to 8 channels and is equipped with advanced event triggers, ensuring significant activities do not go unnoticed.

Finally, the DVS-2408 is a versatile and high-performance system designed for larger facilities. With support for 24 channels and the ability to integrate with various IP cameras, the DVS-2408 delivers exceptional scalability. This model comes with comprehensive software for monitoring and management, allowing for multiple users and custom user permissions.

Together, these Linear video surveillance models represent a robust and reliable solution for modern security needs, featuring the latest technologies and high-quality performance to ensure safety and peace of mind in various environments.