Linear DVS-2400 DXS-31& DXS-32DOOR/WINDOW SENSORS, Test Sensors, Snap sensor onto mounting plate

Page 17
DXS-31 & DXS-32 DOOR/WINDOW SENSORS

DXS-31 & DXS-32 DOOR/WINDOW SENSORS

EXAMPLE INSTALLATION (WITH DXS-31 SHOWN)

The DXS-31 and DXS-32 sensors can be used to monitor doors, windows, cabinets, crawl space doors, gates, freezer doors, and many other moving objects that could be used for intrusion or need to be monitored.

A built-in magnetic switch triggers the sensor when its magnet (mounted on the moving part or the door or window) moves away from the sensor.

The DXS-31 sensor can be wired to external normally closed switches for remote triggering.

The DXS-31 sensor can connect directly to a glass break detector.

SET SENSOR JUMPER

A jumper inside the door/window sensor selects instant or delayed response.

1A. If the sensor is going to be used on the primary entry/exit door make sure that the jumper is in the DELAY position.

1B. If the sensor is going to be used on a window or a door that is not going to be used to enter and exit the premises, set the jumper to the INSTANT position.

LEFT OPENING DOOR

TRANSMITTER

MOUNTED ON

DOOR JAMB

(NOTE: SMALL END OF TRANSMITTER UP)

MAGNET

MOUNTED

ON DOOR

RIGHT OPENING DOOR

TRANSMITTER

MOUNTED ON

DOOR JAMB

(NOTE: SMALL END

OF TRANSMITTER DOWN)

MAGNET MOUNTED

ON DOOR

INSTANT/DELAY

OPTION JUMPER

MAGNET

INPUTALIGNMENT

SELECTMARK

JUMPER

TRANSMIT

INDICATOR

TEST

SWITCH

SLIDING WINDOW

MAGNET MOUNTED

ON WINDOW FRAME

TRANSMITTER

MOUNTED ON

WINDOW SILL

DOUBLE-HUNG

WINDOW

4.Snap sensor onto mounting plate. TRANSMITTER

MOUNTED ON

WINDOW FRAME

MAGNET

MOUNTED

ON WINDOW

SASH STILE

ANTENNA

TWO TYPE 2032

BATTERIES

BATTERY

CLAMP

SCREW

BATTERY CLAMP

EXTERNAL

INPUT

TERMINALS

CHOOSE MOUNTING METHOD

2A. Apply double-stick tape (supplied) to back of sensors and magnets.

2B. Screws are also provided to mount sensors and magnets. Screws are preferred over the double-stick tape in permanent installations.

UL NOTE: Double-stick tape is not allowed in UL installations.

ATTACH SENSORS AND MAGNETS

Allow a maximum of 1/2" between magnet and sensor when door/window is closed.

The magnet height is adjustable and an optional magnet spacer is provided for uneven surfaces.

3B. On doors, mount sensor to door frame and magnet to door.

3B. On windows, mount sensor to window frame and magnet to window.

NOTE: Magnet must line up with mark on sensor case both horizontally & vertically.

4.Snap sensor onto mounting plate.

TEST SENSORS

INSTANT/DELAY

 

OPTION JUMPER

SELECTS

 

INSTANT

SELECTS

DELAY

ATTACH MOUNTING PLATES

USING THE SCREWS OR

DOUBLE-STICK TAPE PROVIDED

NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK TAPE IS NOT ALLOWED IN UL INSTALLATIONS

In Chime Mode, the Console should “ding-dong” when the sensor sends a signal.

5.Open door or window.

Verify that light on the sensor (if there is one) glows momentarily when door/window is opened.

Status indicator on the Console should remain lit for each door/window sensor that is left open.

OPEN DOOR, TRANSMIT INDICATOR SHOULD LIGHT

1.PLACE RECEIVER INTO PROGRAM OR "LEARN" MODE

2.ACTIVATE TRANSMITTER BY OPENING DOOR OR WINDOW

3.VERIFY THAT THE RECEIVER ACCEPTED THE SIGNAL

4.REPLACE TRANSMITTER COVER WHEN FINISHED

NOTE: THE TRANSMIT INDICATOR WILL ONLY LIGHT DURING TRANSMISSIONS WHEN THE CASE IS OPEN (EXCEPT WHEN PUSHING THE CASE FOR TESTING)

15

Image 17
Contents Installation & Programming Instructions SUPERVISED WIRELESS SECURITY CONSOLESECURITY USA & CanadaINTRODUCTION This symbol is for important notesTABLE OF CONTENTS CONSOLE 1.THE DVS-2400SECURITY SYSTEMREMOTE CONTROLS WIRELESS KEYPADDOOR/WINDOW SENSORS SMOKE DETECTOR2.SECURITY SYSTEM FLOOR PLAN DESIGN THE INSTALLATIONEXAMPLE SYSTEM Example Residential Security System Floor PlanDOOR/WINDOW SENSOR 3.TYPICAL SYSTEM SENSORSABOUT SENSOR STATUS SUPERVISION WIRELESS KEYPAD5 4 3 4.CONSOLE FEATURESSwitching to Off Mode stops the alarm siren Switching to Chime Mode stops the alarm sirenType 2AG, 1-ampfuse CONSOLE LOCATION 5.CONSOLE INSTALLATIONCASE LOCKING SCREW WALL MOUNTINGcan talk to the occupants through the external EXTERNAL CONSOLE SPEAKER CONNECTIONEXTERNAL ALARM SIREN CONNECTION Connect the Console to the telephone line if the TELEPHONE LINE CONNECTIONAUTOMATION OUTPUT CONNECTION OPTIONAL not plug the transformer in until the wiring is CONSOLE POWER CONNECTIONBACKUP BATTERY INSTALLATION OPTIONAL complete6.BASIC CONSOLE PROGRAMMING indicator for that sensor will stay litSTART IN TEST MASTER USER CODE 1 GONG & 5 BEEPSFollow the instructions on the previous page to PROGRAMMING DIFFERENT SENSOR TYPESselect a sensor number to program the sensor into For DXT-61, DXT-21, DXS-21, DXT-41,& DXS-62ADXS-10WIRELESS KEYPAD 7.BASIC SENSOR INSTALLATION4.Snap sensor onto mounting plate DXS-31& DXS-32DOOR/WINDOW SENSORSTEST SENSORS LABELING THE SENSORS 8.CUSTOMIZING THE CONSOLEcaused the alarm will fl ash and stops any alarms in progress9.CONSOLE OPERATING MODES OFF MODESECURE EXIT HOME MODESTART IN OFF OR CHIME MODE START IN HOME MODEQUICK ARM AWAY MODEOPTIONAL YOUR USER CODE 1 GONG & 3 BEEPS START HERE HOLDstatus indicators 3 beeps being the strongest signalTEST MODE START IN OFF10.SYSTEM TROUBLE INDICATIONS CONSOLE LOW BATTERYSENSOR LOW BATTERIES SENSOR RADIO TROUBLE11.CUSTOMIZING THE SYSTEM and the sensor status indicator will turn offACTIVATE SENSOR DONE START IN TEST MASTER USER CODE 1 GONG & 5 BEEPS SENSOR8 FOR 8 TUV CHIME ZONE AWAY 1 BING DONE SENSOR NUMBER FOR CHIMESENSOR NUMBER FOR INTERIOR 7 FOR 7 PRS INTERIOR ZONE AWAY 1 BING DONENEW FUNCTION NUMBER FOR SENSOR AWAY 1 BING DONE SENSOR NUMBER FOR FUNCTION CHANGEMAKING A SENSOR PERFORM A DIFFERENT FUNCTION AWAY12.ADVANCED PROGRAMMING SETUP MODEHOME = PROGRAM TEST = REMOVECHANGING A SENSORS SUPERVISION CHANGING A SENSORS RESTORE REQUIREMENTSENTRY DELAY TIME EXIT DELAY TIMEREMOTE CONTROL DISARMING LEVEL REMOTE CONTROL ARMING LEVELFIRE SIREN TIME AUTOMATION OUTPUT TIMESILENT EMERGENCY ALARMS SILENT BURGLARY ALARMSDISABLING QUICK ARMING AUTOMATIC RESTORAL OF BYPASSED SENSORSREMOTE CONTROL ARM/DISARM CHIRP AUTOMATION OUTPUT MODE DURING ALARMAUTOMATION OUTPUT ON DURING AND AFTER ALARM AUTOMATION OUTPUT ON DURING ALARMAUTOMATION OUTPUT WHILE ARMED REMOTE ACCESS PASSWORDAUTOMATION OUTPUT DURING EXIT/ENTRY DELAYS AUTOMATION OUTPUT POLARITYusing these steps. The master user code can be Because access to programming would be impossiblechanged using programming STEP #99 CONSOLE MASTER RESET13.COMMUNICATOR PROGRAMMING SETUP MODEGeneral Communicator Programming Table SETUP MODEGENERAL COMMUNICATOR OPTIONS COMMUNICATOR ENABLE2-WAYAUDIO VOICE RESPONSEDIALING DELAY CALL LIMITERDIALING METHOD 0PROGRAMMING STEP #101REPORTING FORMAT COMMUNICATOR REPORTING OPTIONSCALL ROUTING Communicator Reporting Option TablePRIMARY TELEPHONE NUMBER ACCOUNT NUMBERSECONDARY TELEPHONE NUMBER SUPERVISORY OR PAGER TELEPHONE NUMBERREPORT FORCE ARMING REPORT CONSOLE TROUBLEOPENING AND CLOSING REPORTS POINT ID REPORTINGGENERAL REPORTING CODES COMMUNICATOR REPORTING CODESSTEPS #201-206 General Reporting Codes TableSTEPS #261-266 SYSTEM REPORTING CODESFORCE ARMING REPORTING CODE DURESS REPORTING CODE4 BY 2 FORMAT POINT ID REPORTING CODES 4 BY 2 FORMAT POINT ID ALARM REPORT CODESSTEPS #210-233 4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES4 BY 2 FORMAT POINT ID REPORTING CODES 4 by 2 Format Point ID Reporting Code TableSTEP # PROGRAMMING FUNCTIONWIRELESS PRODUCT NOTICE LINEAR LIMITED WARRANTY14. IMPORTANT INFORMATION FCC NOTICE
Related manuals
Manual 48 pages 58.1 Kb

DVS-2400 specifications

The Linear DVS-1200, DVS-2400, RA-2400, DUAL-824, and DVS-2408 are advanced digital video surveillance systems designed for a variety of security applications. These models offer state-of-the-art features, technologies, and characteristics that enhance security monitoring and recording capabilities.

The DVS-1200 is a compact and efficient digital video recorder that supports up to 12 channels of video input. It features high-resolution recording capabilities, providing clear and detailed images. With real-time playback and advanced motion detection, the DVS-1200 allows users to monitor activities effectively. Its user-friendly interface simplifies configuration and operation, making it accessible for both novice and experienced users.

Upgraded for larger installations, the DVS-2400 supports up to 24 channels. This model is equipped with H.264 video compression technology, significantly reducing storage requirements while maintaining high-quality images. The DVS-2400 also offers remote access capabilities, enabling users to view live footage or playback recorded events from anywhere using a smartphone or computer. Its built-in analytics features allow for motion detection, line crossing alerts, and more, enhancing overall security.

The RA-2400 is a remarkable model designed for robust performance in demanding environments. This recorder not only supports 24 channels but also integrates advanced RAID technology for data redundancy and enhanced storage reliability. The RA-2400 is ideal for applications where data loss is unacceptable, making it suitable for critical infrastructure and high-security locations.

The DUAL-824 model stands out with its unique dual-stream encoding feature. It allows simultaneous recording and streaming of two video resolutions, providing flexibility for different applications such as local monitoring and remote access. This model supports up to 8 channels and is equipped with advanced event triggers, ensuring significant activities do not go unnoticed.

Finally, the DVS-2408 is a versatile and high-performance system designed for larger facilities. With support for 24 channels and the ability to integrate with various IP cameras, the DVS-2408 delivers exceptional scalability. This model comes with comprehensive software for monitoring and management, allowing for multiple users and custom user permissions.

Together, these Linear video surveillance models represent a robust and reliable solution for modern security needs, featuring the latest technologies and high-quality performance to ensure safety and peace of mind in various environments.