Linear DVS-2400 manual Telephone Line Connection, Automation Output Connection Optional

TELEPHONE LINE CONNECTION

✦ Connect the Console to the telephone line if the

system is monitored, requires 2-way audio, or

requires telephone remote command.

✦ Telephone RING & TIP terminals are for connection

to the incoming telephone line.

✦ Seized telephone ring & tip are for connection

to local telephone sets. When the communicator

activates, all the local telephone sets will be

disconnected to prevent an off-hook telephone on

the premises from blocking the communicator call.

TELEPHONE
TERMINAL	LINEAR SECURITY CONSOLE MODEL DVS-2400
BLOCK
	OPTIONAL
	VOICE MODULE
	MODEL: VB-2

TELEPHONE TERMINAL BLOCK

SEIZED RING	TIP
SEIZED TIP	RING

TO LOCAL	R1 T1	R T	TO PHONE
PHONES			LINE

SEIZED	SEIZED	LINE	LINE
TIP (T1)	RING (R1)	TIP (T)	RING (R)

DVS-2400

TELEPHONE

TERMINAL

BLOCK

BROWN

GRAY

8-PIN

MODULAR

PHONE CORD

RED

GREEN

BLUE, ORANGE

BLACK, AND

YELLOW NOT

USED

1.	Install a USOC RJ31-X or RJ38-X jack to the
	telephone system near the Console.
2.	Route an appropriate modular telephone line cord
	from the jack to the Console.
3.	Route the line cord through the Console’s wiring
	access hole.
4.	Connect the incoming telephone line wires to the
	Console's telephone terminal block TIP and RING
	terminals.
5.	Connect the local telephone set wires to the
	Console’s telephone terminal block SEIZED TIP
	and SEIZED RING terminals.

✦When directly connecting (without a telephone line) to the DVS-2400 with the RA-2400 remote access software (Version 1.3 or later), disconnect the incoming telephone line and connect the modem to the panel's TIP and RING terminals (with the modem's red & green phone line wires). Press the EMERGENCY key while

in Test Mode to cause the panel to connect to the modem.

8-POSITION	R1				R	T		T1	SHORTING BAR
USOC RJ31-X									SHORT REMOVED
(OR RJ38-X)									ON PLUG
JACK	1	2	3	4	5	6	7	8	INSERTION

	R	T1	TO LOCAL
TO TELEPHONE	T
			TELEPHONE
		R1
NETWORK			SETS

CONNECT TELEPHONE LINE

TO THE TELEPHONE

TERMINAL BLOCK

AUTOMATION OUTPUT CONNECTION (OPTIONAL)

✦The Console provides a Automation Output to control lights, devices and appliances.

✦Automation Output can connect to most popular home automation devices and other simple electronic devices (see fi gure).

✦Press to turn the Automation Output on, press again to turn it off.

Programmable Options

✦ There are many programmable options for the

Automation Output.

	LINEAR SECURITY CONSOLE MODEL DVS-2400
MAIN
TERMINAL
BLOCK	OPTIONAL
	VOICE MODULE
	MODEL: VB-2

MINUS H/A TERMINAL WILL SWITCH TO GROUND WHEN AUTOMATION OUTPUT IS ACTIVATED

MAIN TERMINAL BLOCK

	AC
LIGHT EMITTING	AC
	EXT. SPKR
DIODE (L.E.D.)	(-)
	H/A -
	H/A +
	RELAY N.O.
	RELAY DRY

POSITIVE H/A TERMINAL PROVIDES +12 VOLTS DC AND IS CURRENT LIMITED AT 30 MILLIAMPS MAXIMUM

✦ The Automation Output can be programmed for a

variety of useful functions, such as: fl ashing during

alarm, fl ashing after an alarm, on while armed, or,

on during exit/entry delays.

✦ See the “Advanced Programming” section of this

manual for details on changing the function of the

Automation Output.

	EXAMPLE AUTOMATION OUTPUT HOOK-UPS
	X-10	LINEAR RB-90
X-10	BURGLAR ALARM
		RELAY MODULE
	INTERFACE
		YOUR
	(CAN CONTROL	LOAD	LIGHT
	HOUSE LIGHTS
			EMITTING
	THROUGH X-10
			DIODE
	SYSTEM)
			(L.E.D.)

POWER

SOURCE

H/A + H/A - H/A + H/A - H/A + H/A -

10