Linear DVS-2400 manual Automation Output Mode During Alarm, Automation Activation Tone

Page 31
AUTOMATION OUTPUT MODE DURING ALARM

AUTOMATION OUTPUT MODE DURING ALARM

The factory setting causes the Automation Output to fl ash if it is programmed to activate during or after an alarm.

NOTE: For the Automation Output to activate during or after an alarm, that function must be enabled with Programming Step 71 or 72.

STEP #68 The output can be programmed to be a steady output using this step.

6MNO

PROGRAMMING STEP #68

8TUV

HOME PROGRAM

0 FOR FLASHING OUTPUT ON ALARM

1 FOR STEADY OUTPUT ON ALARM

AWAY STORE PROGRAM

AUTOMATION ACTIVATION TONE

The factory setting causes the Console to sound a

“Bing” when the Automation Output is activated by pressing the AUTOMATION ACTIVATION TONE key, or when it's triggered with a two-button remote control.

STEP #69 This sound can be silenced using this step.

6MNO

PROGRAMMING STEP #69

9WXY

HOME PROGRAM

0 FOR BING TONE OFF

1 FOR BING TONE ON

AWAY STORE PROGRAM

REMOTE CONTROL ARM/DISARM CHIRP

When arming with the portable remote control, the factory setting causes the Console to “chirp” once when armed, twice when disarmed, and three times when arming with sensors bypassed.

STEP #70 These chirps can be silenced using this step.

NOTE: If these chirps are silenced, it is recommended to program the Automation Output to be active when the system is armed, so a light can be triggered displaying the arming status of the Console.

7PRS

PROGRAMMING STEP #70

0

HOME PROGRAM

0 FOR CHIRPS OFF

1 FOR CHIRPS ON

AWAY STORE PROGRAM

AUTOMATION OUTPUT ON DURING AND AFTER ALARM

The factory setting causes the Console's

Automation Output to activate when pressing the REMOTE CONTROL ARM/DISARM CHIRP key, or when it's triggered with a two-button remote control.

STEP #71 The Console can be programmed to activate the Automation Output during and after any alarms as well as when normally triggered using this step.

7PRS

1

HOME

PROGRAMMING STEP #71

PROGRAM

0 FOR STANDARD TRIGGER

1 FOR FLASHING DURING & AFTER ALARM

NOTE: The output will continue until the flashing sensor status lights are cleared.

AWAY

STORE PROGRAM

AUTOMATION OUTPUT ON DURING ALARM

The factory setting causes the Console's

Automation Output to activate when pressing the AUTOMATION OUTPUT ON DURING AND AFTER ALARM key, or when it's triggered with a two-button remote control.

STEP #72 The Console can be programmed to activate the Automation Output during alarms as well as when normally triggered using this step.

NOTE: The Automation Output can be programmed to flash or be steady during alarm, see Programming Step 68.

7PRS

PROGRAMMING STEP #72

2ABC

HOME PROGRAM

0 FOR STANDARD TRIGGER

1 FOR OUTPUT DURING ALARM

AWAY STORE PROGRAM

29

Image 31
Contents USA & Canada SUPERVISED WIRELESS SECURITY CONSOLEInstallation & Programming Instructions SECURITYINTRODUCTION This symbol is for important notesTABLE OF CONTENTS CONSOLE 1.THE DVS-2400SECURITY SYSTEMSMOKE DETECTOR WIRELESS KEYPADREMOTE CONTROLS DOOR/WINDOW SENSORSExample Residential Security System Floor Plan DESIGN THE INSTALLATION2.SECURITY SYSTEM FLOOR PLAN EXAMPLE SYSTEMWIRELESS KEYPAD 3.TYPICAL SYSTEM SENSORSDOOR/WINDOW SENSOR ABOUT SENSOR STATUS SUPERVISIONSwitching to Chime Mode stops the alarm siren 4.CONSOLE FEATURES5 4 3 Switching to Off Mode stops the alarm sirenType 2AG, 1-ampfuse WALL MOUNTING 5.CONSOLE INSTALLATIONCONSOLE LOCATION CASE LOCKING SCREWEXTERNAL ALARM SIREN CONNECTION EXTERNAL CONSOLE SPEAKER CONNECTIONcan talk to the occupants through the external AUTOMATION OUTPUT CONNECTION OPTIONAL TELEPHONE LINE CONNECTIONConnect the Console to the telephone line if the complete CONSOLE POWER CONNECTIONnot plug the transformer in until the wiring is BACKUP BATTERY INSTALLATION OPTIONALMASTER USER CODE 1 GONG & 5 BEEPS indicator for that sensor will stay lit6.BASIC CONSOLE PROGRAMMING START IN TESTFor DXT-61, DXT-21, DXS-21, DXT-41,& DXS-62A PROGRAMMING DIFFERENT SENSOR TYPESFollow the instructions on the previous page to select a sensor number to program the sensor intoDXS-10WIRELESS KEYPAD 7.BASIC SENSOR INSTALLATIONTEST SENSORS DXS-31& DXS-32DOOR/WINDOW SENSORS4.Snap sensor onto mounting plate LABELING THE SENSORS 8.CUSTOMIZING THE CONSOLEOFF MODE and stops any alarms in progresscaused the alarm will fl ash 9.CONSOLE OPERATING MODESSTART IN HOME MODE HOME MODESECURE EXIT START IN OFF OR CHIME MODESTART HERE HOLD AWAY MODEQUICK ARM OPTIONAL YOUR USER CODE 1 GONG & 3 BEEPSSTART IN OFF 3 beeps being the strongest signalstatus indicators TEST MODESENSOR RADIO TROUBLE CONSOLE LOW BATTERY10.SYSTEM TROUBLE INDICATIONS SENSOR LOW BATTERIESMASTER USER CODE 1 GONG & 5 BEEPS SENSOR and the sensor status indicator will turn off11.CUSTOMIZING THE SYSTEM ACTIVATE SENSOR DONE START IN TEST7 FOR 7 PRS INTERIOR ZONE AWAY 1 BING DONE SENSOR NUMBER FOR CHIME8 FOR 8 TUV CHIME ZONE AWAY 1 BING DONE SENSOR NUMBER FOR INTERIORAWAY SENSOR NUMBER FOR FUNCTION CHANGENEW FUNCTION NUMBER FOR SENSOR AWAY 1 BING DONE MAKING A SENSOR PERFORM A DIFFERENT FUNCTIONTEST = REMOVE SETUP MODE12.ADVANCED PROGRAMMING HOME = PROGRAMEXIT DELAY TIME CHANGING A SENSORS RESTORE REQUIREMENTSCHANGING A SENSORS SUPERVISION ENTRY DELAY TIMEAUTOMATION OUTPUT TIME REMOTE CONTROL ARMING LEVELREMOTE CONTROL DISARMING LEVEL FIRE SIREN TIMEAUTOMATIC RESTORAL OF BYPASSED SENSORS SILENT BURGLARY ALARMSSILENT EMERGENCY ALARMS DISABLING QUICK ARMINGAUTOMATION OUTPUT ON DURING ALARM AUTOMATION OUTPUT MODE DURING ALARMREMOTE CONTROL ARM/DISARM CHIRP AUTOMATION OUTPUT ON DURING AND AFTER ALARMAUTOMATION OUTPUT POLARITY REMOTE ACCESS PASSWORDAUTOMATION OUTPUT WHILE ARMED AUTOMATION OUTPUT DURING EXIT/ENTRY DELAYSCONSOLE MASTER RESET Because access to programming would be impossibleusing these steps. The master user code can be changed using programming STEP #99SETUP MODE SETUP MODE13.COMMUNICATOR PROGRAMMING General Communicator Programming TableVOICE RESPONSE COMMUNICATOR ENABLEGENERAL COMMUNICATOR OPTIONS 2-WAYAUDIO0PROGRAMMING STEP #101 CALL LIMITERDIALING DELAY DIALING METHODCommunicator Reporting Option Table COMMUNICATOR REPORTING OPTIONSREPORTING FORMAT CALL ROUTINGSUPERVISORY OR PAGER TELEPHONE NUMBER ACCOUNT NUMBERPRIMARY TELEPHONE NUMBER SECONDARY TELEPHONE NUMBERPOINT ID REPORTING REPORT CONSOLE TROUBLEREPORT FORCE ARMING OPENING AND CLOSING REPORTSGeneral Reporting Codes Table COMMUNICATOR REPORTING CODESGENERAL REPORTING CODES STEPS #201-206DURESS REPORTING CODE SYSTEM REPORTING CODESSTEPS #261-266 FORCE ARMING REPORTING CODE4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES 4 BY 2 FORMAT POINT ID ALARM REPORT CODES4 BY 2 FORMAT POINT ID REPORTING CODES STEPS #210-233PROGRAMMING FUNCTION 4 by 2 Format Point ID Reporting Code Table4 BY 2 FORMAT POINT ID REPORTING CODES STEP #FCC NOTICE LINEAR LIMITED WARRANTYWIRELESS PRODUCT NOTICE 14. IMPORTANT INFORMATION
Related manuals
Manual 48 pages 58.1 Kb

DVS-2400 specifications

The Linear DVS-1200, DVS-2400, RA-2400, DUAL-824, and DVS-2408 are advanced digital video surveillance systems designed for a variety of security applications. These models offer state-of-the-art features, technologies, and characteristics that enhance security monitoring and recording capabilities.

The DVS-1200 is a compact and efficient digital video recorder that supports up to 12 channels of video input. It features high-resolution recording capabilities, providing clear and detailed images. With real-time playback and advanced motion detection, the DVS-1200 allows users to monitor activities effectively. Its user-friendly interface simplifies configuration and operation, making it accessible for both novice and experienced users.

Upgraded for larger installations, the DVS-2400 supports up to 24 channels. This model is equipped with H.264 video compression technology, significantly reducing storage requirements while maintaining high-quality images. The DVS-2400 also offers remote access capabilities, enabling users to view live footage or playback recorded events from anywhere using a smartphone or computer. Its built-in analytics features allow for motion detection, line crossing alerts, and more, enhancing overall security.

The RA-2400 is a remarkable model designed for robust performance in demanding environments. This recorder not only supports 24 channels but also integrates advanced RAID technology for data redundancy and enhanced storage reliability. The RA-2400 is ideal for applications where data loss is unacceptable, making it suitable for critical infrastructure and high-security locations.

The DUAL-824 model stands out with its unique dual-stream encoding feature. It allows simultaneous recording and streaming of two video resolutions, providing flexibility for different applications such as local monitoring and remote access. This model supports up to 8 channels and is equipped with advanced event triggers, ensuring significant activities do not go unnoticed.

Finally, the DVS-2408 is a versatile and high-performance system designed for larger facilities. With support for 24 channels and the ability to integrate with various IP cameras, the DVS-2408 delivers exceptional scalability. This model comes with comprehensive software for monitoring and management, allowing for multiple users and custom user permissions.

Together, these Linear video surveillance models represent a robust and reliable solution for modern security needs, featuring the latest technologies and high-quality performance to ensure safety and peace of mind in various environments.