Linear DVS-2400 manual Automation Output While Armed, Automation Output During Exit/Entry Delays

Page 32
AUTOMATION OUTPUT WHILE ARMED

AUTOMATION OUTPUT WHILE ARMED

The factory setting causes the Console's

Automation Output to activate when pressing the AUTOMATION OUTPUT DURING EXIT/ENTRY DELAYS key, or when it's triggered with a two-button remote control.

STEP #73 The Console can be programmed to activate the Automation Output when the system is armed as well as when normally triggered using this step.

7PRS

PROGRAMMING STEP #73

3DEF

HOME PROGRAM

0 FOR STANDARD TRIGGER

1 FOR OUTPUT WHEN ARMED

AWAY STORE PROGRAM

AUTOMATION OUTPUT DURING EXIT/ENTRY DELAYS

The factory setting causes the Console's

Automation Output to activate when pressing the AUTOMATION OUTPUT POLARITY key, or when it's triggered with a two-button remote control.

STEP #74 The Console can be programmed to activate the Automation Output during the exit and Entry Delays as well as when normally triggered using this step.

7PRS

PROGRAMMING STEP #74

4GHI

HOME PROGRAM

0 FOR STANDARD TRIGGER

REMOTE ACCESS PASSWORDDURESS CODE 1 FOR OUTPUT DURING MASTER USER CODE EXIT/ENTRY DELAYS

AWAY

STORE PROGRAM

AUTOMATION OUTPUT POLARITY

The factory setting causes the Console's Automation Output to provide a current limited voltage source when activated.

STEP #75 The Console can be programmed so the Automation Output provides a current limited voltage source when deactivated using this step.

7PRS

PROGRAMMING STEP #75

5JKL

HOME PROGRAM

0 FOR VOLTAGE WHEN OFF

1 FOR VOLTAGE WHEN ON

AWAY STORE PROGRAM

REMOTE ACCESS PASSWORD

This password is used to gain access to the Console when using the RA-2400 remote access software. The password must be 6-digits long.

STEP #87 Use this step to enter a new remote access password then log the password in the box below.

REMOTE ACCESS PASSWORD:

8TUV

PROGRAMMING STEP #87

7PRS

HOME PROGRAM

6-DIGIT REMOTE ACCESS PASSWORD

AWAY STORE PROGRAM

DURESS CODE

The duress code will disarm the system, without any special indications or sounds, but will send the programmed duress code to the Central Station. The code should be two or more digits different than any user code

STEP #92 Use this step to enter the duress code then log the code in the box below.

DURESS CODE:

9WXY

PROGRAMMING STEP #92

2ABC

HOME PROGRAM

1-5 DIGIT DURESS CODE (3-5 DIGITS RECOMMENDED)

AWAY STORE PROGRAM

MASTER USER CODE

The master user code is 1234 when power is fi rst applied to the Console.

The master user code can be changed to any 1-5 digit code. Only the master user can access Setup Mode, restricted users cannot.

NOTE: For maximum security, a 3-5 digit code is recommended.

STEP #99 Use this step to enter the new master user code then log the code in the box below.

9WXY

PROGRAMMING STEP #99

9WXY

HOME PROGRAM

1-5 DIGIT MASTER CODE (3-5 DIGITS RECOMMENDED)

AWAY STORE PROGRAM

MASTER USER CODE:

30

Image 32
Contents SUPERVISED WIRELESS SECURITY CONSOLE Installation & Programming InstructionsSECURITY USA & CanadaThis symbol is for important notes INTRODUCTIONTABLE OF CONTENTS 1.THE DVS-2400SECURITY SYSTEM CONSOLEWIRELESS KEYPAD REMOTE CONTROLSDOOR/WINDOW SENSORS SMOKE DETECTORDESIGN THE INSTALLATION 2.SECURITY SYSTEM FLOOR PLANEXAMPLE SYSTEM Example Residential Security System Floor Plan3.TYPICAL SYSTEM SENSORS DOOR/WINDOW SENSORABOUT SENSOR STATUS SUPERVISION WIRELESS KEYPAD4.CONSOLE FEATURES 5 4 3Switching to Off Mode stops the alarm siren Switching to Chime Mode stops the alarm sirenType 2AG, 1-ampfuse 5.CONSOLE INSTALLATION CONSOLE LOCATIONCASE LOCKING SCREW WALL MOUNTINGcan talk to the occupants through the external EXTERNAL CONSOLE SPEAKER CONNECTIONEXTERNAL ALARM SIREN CONNECTION Connect the Console to the telephone line if the TELEPHONE LINE CONNECTIONAUTOMATION OUTPUT CONNECTION OPTIONAL CONSOLE POWER CONNECTION not plug the transformer in until the wiring isBACKUP BATTERY INSTALLATION OPTIONAL completeindicator for that sensor will stay lit 6.BASIC CONSOLE PROGRAMMINGSTART IN TEST MASTER USER CODE 1 GONG & 5 BEEPSPROGRAMMING DIFFERENT SENSOR TYPES Follow the instructions on the previous page toselect a sensor number to program the sensor into For DXT-61, DXT-21, DXS-21, DXT-41,& DXS-62A7.BASIC SENSOR INSTALLATION DXS-10WIRELESS KEYPAD4.Snap sensor onto mounting plate DXS-31& DXS-32DOOR/WINDOW SENSORSTEST SENSORS 8.CUSTOMIZING THE CONSOLE LABELING THE SENSORSand stops any alarms in progress caused the alarm will fl ash9.CONSOLE OPERATING MODES OFF MODEHOME MODE SECURE EXITSTART IN OFF OR CHIME MODE START IN HOME MODEAWAY MODE QUICK ARMOPTIONAL YOUR USER CODE 1 GONG & 3 BEEPS START HERE HOLD3 beeps being the strongest signal status indicatorsTEST MODE START IN OFFCONSOLE LOW BATTERY 10.SYSTEM TROUBLE INDICATIONSSENSOR LOW BATTERIES SENSOR RADIO TROUBLEand the sensor status indicator will turn off 11.CUSTOMIZING THE SYSTEMACTIVATE SENSOR DONE START IN TEST MASTER USER CODE 1 GONG & 5 BEEPS SENSORSENSOR NUMBER FOR CHIME 8 FOR 8 TUV CHIME ZONE AWAY 1 BING DONESENSOR NUMBER FOR INTERIOR 7 FOR 7 PRS INTERIOR ZONE AWAY 1 BING DONESENSOR NUMBER FOR FUNCTION CHANGE NEW FUNCTION NUMBER FOR SENSOR AWAY 1 BING DONEMAKING A SENSOR PERFORM A DIFFERENT FUNCTION AWAYSETUP MODE 12.ADVANCED PROGRAMMINGHOME = PROGRAM TEST = REMOVECHANGING A SENSORS RESTORE REQUIREMENTS CHANGING A SENSORS SUPERVISIONENTRY DELAY TIME EXIT DELAY TIMEREMOTE CONTROL ARMING LEVEL REMOTE CONTROL DISARMING LEVELFIRE SIREN TIME AUTOMATION OUTPUT TIMESILENT BURGLARY ALARMS SILENT EMERGENCY ALARMSDISABLING QUICK ARMING AUTOMATIC RESTORAL OF BYPASSED SENSORSAUTOMATION OUTPUT MODE DURING ALARM REMOTE CONTROL ARM/DISARM CHIRPAUTOMATION OUTPUT ON DURING AND AFTER ALARM AUTOMATION OUTPUT ON DURING ALARMREMOTE ACCESS PASSWORD AUTOMATION OUTPUT WHILE ARMEDAUTOMATION OUTPUT DURING EXIT/ENTRY DELAYS AUTOMATION OUTPUT POLARITYBecause access to programming would be impossible using these steps. The master user code can bechanged using programming STEP #99 CONSOLE MASTER RESETSETUP MODE 13.COMMUNICATOR PROGRAMMINGGeneral Communicator Programming Table SETUP MODECOMMUNICATOR ENABLE GENERAL COMMUNICATOR OPTIONS2-WAYAUDIO VOICE RESPONSECALL LIMITER DIALING DELAYDIALING METHOD 0PROGRAMMING STEP #101COMMUNICATOR REPORTING OPTIONS REPORTING FORMATCALL ROUTING Communicator Reporting Option TableACCOUNT NUMBER PRIMARY TELEPHONE NUMBERSECONDARY TELEPHONE NUMBER SUPERVISORY OR PAGER TELEPHONE NUMBERREPORT CONSOLE TROUBLE REPORT FORCE ARMINGOPENING AND CLOSING REPORTS POINT ID REPORTINGCOMMUNICATOR REPORTING CODES GENERAL REPORTING CODESSTEPS #201-206 General Reporting Codes TableSYSTEM REPORTING CODES STEPS #261-266FORCE ARMING REPORTING CODE DURESS REPORTING CODE4 BY 2 FORMAT POINT ID ALARM REPORT CODES 4 BY 2 FORMAT POINT ID REPORTING CODESSTEPS #210-233 4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES4 by 2 Format Point ID Reporting Code Table 4 BY 2 FORMAT POINT ID REPORTING CODESSTEP # PROGRAMMING FUNCTIONLINEAR LIMITED WARRANTY WIRELESS PRODUCT NOTICE14. IMPORTANT INFORMATION FCC NOTICE
Related manuals
Manual 48 pages 58.1 Kb

DVS-2400 specifications

The Linear DVS-1200, DVS-2400, RA-2400, DUAL-824, and DVS-2408 are advanced digital video surveillance systems designed for a variety of security applications. These models offer state-of-the-art features, technologies, and characteristics that enhance security monitoring and recording capabilities.

The DVS-1200 is a compact and efficient digital video recorder that supports up to 12 channels of video input. It features high-resolution recording capabilities, providing clear and detailed images. With real-time playback and advanced motion detection, the DVS-1200 allows users to monitor activities effectively. Its user-friendly interface simplifies configuration and operation, making it accessible for both novice and experienced users.

Upgraded for larger installations, the DVS-2400 supports up to 24 channels. This model is equipped with H.264 video compression technology, significantly reducing storage requirements while maintaining high-quality images. The DVS-2400 also offers remote access capabilities, enabling users to view live footage or playback recorded events from anywhere using a smartphone or computer. Its built-in analytics features allow for motion detection, line crossing alerts, and more, enhancing overall security.

The RA-2400 is a remarkable model designed for robust performance in demanding environments. This recorder not only supports 24 channels but also integrates advanced RAID technology for data redundancy and enhanced storage reliability. The RA-2400 is ideal for applications where data loss is unacceptable, making it suitable for critical infrastructure and high-security locations.

The DUAL-824 model stands out with its unique dual-stream encoding feature. It allows simultaneous recording and streaming of two video resolutions, providing flexibility for different applications such as local monitoring and remote access. This model supports up to 8 channels and is equipped with advanced event triggers, ensuring significant activities do not go unnoticed.

Finally, the DVS-2408 is a versatile and high-performance system designed for larger facilities. With support for 24 channels and the ability to integrate with various IP cameras, the DVS-2408 delivers exceptional scalability. This model comes with comprehensive software for monitoring and management, allowing for multiple users and custom user permissions.

Together, these Linear video surveillance models represent a robust and reliable solution for modern security needs, featuring the latest technologies and high-quality performance to ensure safety and peace of mind in various environments.