Linear DVS-2400 manual General Communicator Options, Communicator Enable, Wayaudio, Voice Response

Page 35
GENERAL COMMUNICATOR OPTIONS

GENERAL COMMUNICATOR OPTIONS

COMMUNICATOR ENABLE

The factory setting for the Console disables the communicator. If the system is going to be a non-monitored, local alarm only, leave the communicator disabled.

STEP #107 If the system is going to be monitored by a Central Station, enable the communicator with this programming step.

1

0PROGRAMMING STEP #107

7PRS

HOME PROGRAM

0 FOR COMMUNICATOR OFF

1 FOR COMMUNICATOR ON

AWAY STORE PROGRAM

2-WAY AUDIO

When the Model VB-2 voice module is installed, the communicator can provide 2-way audio capability.

The audio module can be programmed for listen-only, 2-way manual operation (using a pushbutton telephone at the Central Station), and 2-way full duplex hands free operation.

Refer to the VB-2 installation instructions for details on operating the audio module.

NOTE: The Model VB-2 digital voice response module must be installed for this option to function.

7PRS

PROGRAMMING STEP #76

6MNO

HOME PROGRAM

0 FOR NO AUDIO MONITORING

1 FOR LISTEN-ONLY

2 FOR 2-WAY MANUAL

3 FOR 2-WAY FULL DUPLEX

AWAY STORE PROGRAM

The factory setting for the VB-2 audio module is OFF.

STEP #76 The audio module can be set for (1) listen-only, (2) 2-way manual, (3) 2-way full duplex using this step.

NOTE: For safety, 2-way audio will not activate if the system is disarmed with the duress code.

NOTE:Units programmed for two-way duplex can still be controlled manually by pressing the “1” or “3” key. In addition, the Central Station can return the unit to two-way duplex by pressing the “8” key.

VOICE RESPONSE

The Console can be programmed to allow the speaker to play audio produced by the VB-2 digital voice response module.

This selection can also be used when a remote speaker is connected to the Console.

The factory setting is to disable the speaker from playing voice module audio.

STEP #78 The Console can be programmed to enable voice module audio using this step.

NOTE:Turning voice response OFF with this programming step will only effect the audio produced by the voice module. It will not stop the Console’s speaker from sounding local sirens and tones.

NOTE: A Model VB-2 digital voice response module must be installed for this option to function.

7PRS

PROGRAMMING STEP #78

8TUV

HOME PROGRAM

0 FOR NO VOICE RESPONSE

1 FOR VOICE RESPONSE

AWAY STORE PROGRAM

REMOTE LOCKOUT

The factory setting for the communicator allows remote connection to the Console with Linear's RA-2400 Remote Access Software and a modem (unlocked).

STEP #100 The Console can be programmed to not answer incoming calls, thereby, not allowing remote access (locked) using this step.

1

0PROGRAMMING STEP #100

0

HOME PROGRAM

0 FOR UNLOCK

1 FOR LOCK

AWAY STORE PROGRAM

33

Image 35
Contents USA & Canada SUPERVISED WIRELESS SECURITY CONSOLEInstallation & Programming Instructions SECURITYINTRODUCTION This symbol is for important notesTABLE OF CONTENTS CONSOLE 1.THE DVS-2400SECURITY SYSTEMSMOKE DETECTOR WIRELESS KEYPADREMOTE CONTROLS DOOR/WINDOW SENSORSExample Residential Security System Floor Plan DESIGN THE INSTALLATION2.SECURITY SYSTEM FLOOR PLAN EXAMPLE SYSTEMWIRELESS KEYPAD 3.TYPICAL SYSTEM SENSORSDOOR/WINDOW SENSOR ABOUT SENSOR STATUS SUPERVISIONSwitching to Chime Mode stops the alarm siren 4.CONSOLE FEATURES5 4 3 Switching to Off Mode stops the alarm sirenType 2AG, 1-ampfuse WALL MOUNTING 5.CONSOLE INSTALLATIONCONSOLE LOCATION CASE LOCKING SCREWcan talk to the occupants through the external EXTERNAL CONSOLE SPEAKER CONNECTIONEXTERNAL ALARM SIREN CONNECTION Connect the Console to the telephone line if the TELEPHONE LINE CONNECTIONAUTOMATION OUTPUT CONNECTION OPTIONAL complete CONSOLE POWER CONNECTIONnot plug the transformer in until the wiring is BACKUP BATTERY INSTALLATION OPTIONALMASTER USER CODE 1 GONG & 5 BEEPS indicator for that sensor will stay lit6.BASIC CONSOLE PROGRAMMING START IN TESTFor DXT-61, DXT-21, DXS-21, DXT-41,& DXS-62A PROGRAMMING DIFFERENT SENSOR TYPESFollow the instructions on the previous page to select a sensor number to program the sensor intoDXS-10WIRELESS KEYPAD 7.BASIC SENSOR INSTALLATION4.Snap sensor onto mounting plate DXS-31& DXS-32DOOR/WINDOW SENSORSTEST SENSORS LABELING THE SENSORS 8.CUSTOMIZING THE CONSOLEOFF MODE and stops any alarms in progresscaused the alarm will fl ash 9.CONSOLE OPERATING MODESSTART IN HOME MODE HOME MODESECURE EXIT START IN OFF OR CHIME MODESTART HERE HOLD AWAY MODEQUICK ARM OPTIONAL YOUR USER CODE 1 GONG & 3 BEEPSSTART IN OFF 3 beeps being the strongest signalstatus indicators TEST MODESENSOR RADIO TROUBLE CONSOLE LOW BATTERY10.SYSTEM TROUBLE INDICATIONS SENSOR LOW BATTERIESMASTER USER CODE 1 GONG & 5 BEEPS SENSOR and the sensor status indicator will turn off11.CUSTOMIZING THE SYSTEM ACTIVATE SENSOR DONE START IN TEST7 FOR 7 PRS INTERIOR ZONE AWAY 1 BING DONE SENSOR NUMBER FOR CHIME8 FOR 8 TUV CHIME ZONE AWAY 1 BING DONE SENSOR NUMBER FOR INTERIORAWAY SENSOR NUMBER FOR FUNCTION CHANGENEW FUNCTION NUMBER FOR SENSOR AWAY 1 BING DONE MAKING A SENSOR PERFORM A DIFFERENT FUNCTIONTEST = REMOVE SETUP MODE12.ADVANCED PROGRAMMING HOME = PROGRAMEXIT DELAY TIME CHANGING A SENSORS RESTORE REQUIREMENTSCHANGING A SENSORS SUPERVISION ENTRY DELAY TIMEAUTOMATION OUTPUT TIME REMOTE CONTROL ARMING LEVELREMOTE CONTROL DISARMING LEVEL FIRE SIREN TIMEAUTOMATIC RESTORAL OF BYPASSED SENSORS SILENT BURGLARY ALARMSSILENT EMERGENCY ALARMS DISABLING QUICK ARMINGAUTOMATION OUTPUT ON DURING ALARM AUTOMATION OUTPUT MODE DURING ALARMREMOTE CONTROL ARM/DISARM CHIRP AUTOMATION OUTPUT ON DURING AND AFTER ALARMAUTOMATION OUTPUT POLARITY REMOTE ACCESS PASSWORDAUTOMATION OUTPUT WHILE ARMED AUTOMATION OUTPUT DURING EXIT/ENTRY DELAYSCONSOLE MASTER RESET Because access to programming would be impossibleusing these steps. The master user code can be changed using programming STEP #99SETUP MODE SETUP MODE13.COMMUNICATOR PROGRAMMING General Communicator Programming TableVOICE RESPONSE COMMUNICATOR ENABLEGENERAL COMMUNICATOR OPTIONS 2-WAYAUDIO0PROGRAMMING STEP #101 CALL LIMITERDIALING DELAY DIALING METHODCommunicator Reporting Option Table COMMUNICATOR REPORTING OPTIONSREPORTING FORMAT CALL ROUTINGSUPERVISORY OR PAGER TELEPHONE NUMBER ACCOUNT NUMBERPRIMARY TELEPHONE NUMBER SECONDARY TELEPHONE NUMBERPOINT ID REPORTING REPORT CONSOLE TROUBLEREPORT FORCE ARMING OPENING AND CLOSING REPORTSGeneral Reporting Codes Table COMMUNICATOR REPORTING CODESGENERAL REPORTING CODES STEPS #201-206DURESS REPORTING CODE SYSTEM REPORTING CODESSTEPS #261-266 FORCE ARMING REPORTING CODE4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES 4 BY 2 FORMAT POINT ID ALARM REPORT CODES4 BY 2 FORMAT POINT ID REPORTING CODES STEPS #210-233PROGRAMMING FUNCTION 4 by 2 Format Point ID Reporting Code Table4 BY 2 FORMAT POINT ID REPORTING CODES STEP #FCC NOTICE LINEAR LIMITED WARRANTYWIRELESS PRODUCT NOTICE 14. IMPORTANT INFORMATION
Related manuals
Manual 48 pages 58.1 Kb

DVS-2400 specifications

The Linear DVS-1200, DVS-2400, RA-2400, DUAL-824, and DVS-2408 are advanced digital video surveillance systems designed for a variety of security applications. These models offer state-of-the-art features, technologies, and characteristics that enhance security monitoring and recording capabilities.

The DVS-1200 is a compact and efficient digital video recorder that supports up to 12 channels of video input. It features high-resolution recording capabilities, providing clear and detailed images. With real-time playback and advanced motion detection, the DVS-1200 allows users to monitor activities effectively. Its user-friendly interface simplifies configuration and operation, making it accessible for both novice and experienced users.

Upgraded for larger installations, the DVS-2400 supports up to 24 channels. This model is equipped with H.264 video compression technology, significantly reducing storage requirements while maintaining high-quality images. The DVS-2400 also offers remote access capabilities, enabling users to view live footage or playback recorded events from anywhere using a smartphone or computer. Its built-in analytics features allow for motion detection, line crossing alerts, and more, enhancing overall security.

The RA-2400 is a remarkable model designed for robust performance in demanding environments. This recorder not only supports 24 channels but also integrates advanced RAID technology for data redundancy and enhanced storage reliability. The RA-2400 is ideal for applications where data loss is unacceptable, making it suitable for critical infrastructure and high-security locations.

The DUAL-824 model stands out with its unique dual-stream encoding feature. It allows simultaneous recording and streaming of two video resolutions, providing flexibility for different applications such as local monitoring and remote access. This model supports up to 8 channels and is equipped with advanced event triggers, ensuring significant activities do not go unnoticed.

Finally, the DVS-2408 is a versatile and high-performance system designed for larger facilities. With support for 24 channels and the ability to integrate with various IP cameras, the DVS-2408 delivers exceptional scalability. This model comes with comprehensive software for monitoring and management, allowing for multiple users and custom user permissions.

Together, these Linear video surveillance models represent a robust and reliable solution for modern security needs, featuring the latest technologies and high-quality performance to ensure safety and peace of mind in various environments.