On-Q/Legrand HMS 1100 owner manual Emergency Keys, Fire Alarm Activated, Gas Alarm Activated

Page 18

For more information on the digital and voice dialer - See Digital Dialer and Voice Dialer.

•The system continues to sound all alarms and flash the flashing light for 1-30 minutes after the alarm is activated.

•After a 1-30 minute period, the sounder is turned off, and the alarm system resets itself. The console beeper stays on. If a zone is tripped after a reset, the sounder will again be activated, and the dialer will again dial out.

At any time, the alarm system can be turned off at the console.

Fire Alarm Activated

When the fire alarm is activated by the smoke/fire detector(s), the alarm responds exactly as described under Burglar Alarm Activated, except:

•The console display reads, "FIRE ALARM! ZONE NAME TRIPPED".

•The sounder will activate in a 3 pulse temporal pattern to distinguish the fire alarm from the burglar alarm.

The fire alarm takes priority over the burglar alarm, however, if a gas alarm is already active, it will not override the gas alarm.

NOTE: If multiple alarm types occur, such as both Fire and Police, the display will alternate between the alarm types.

Gas Alarm Activated

When the gas alarm is activated, the alarm responds exactly as described under Burglar Alarm Activated, except:

•The console display reads, "GAS ALARM! ZONE NAME TRIPPED".

•The sounder will pulse on - off - on, then an extended off period to distinguish it from the burglar or fire alarm. The gas alarm takes priority over the burglar alarm, however, if a fire alarm is already active, it will not override the fire alarm.

Emergency Keys

Emergency alarm conditions can be activated through the console. These conditions (Fire, Police, and Auxiliary) are initiated with the simultaneous depression of two keys for approximately 1-second.

NOTE: The Emergency keys are always armed. The Fire and Auxiliary emergency alarms are silenced by pressing the ' * ' key. To cancel a Police emergency alarm you must press the Off key and enter your code.

Page 10

Image 18

Contents HMS Page Contents Control Telephone Control Page Underwriters Laboratories Requirements Page Introduction Underwriters Laboratories UL ListingOverall Description Console OperationNormal Top-Level Display Display MenusTrouble Beeps Error BeepsMain Menu To silence the beeper, press the * keyAreas HMS 1100 MaintenanceCancel Confirmation BeepArming the Security System Disarming the Security System and Silencing AlarmsSecurity System Operation = OFF= Night Using Shortcut Keys= Night DLY Night Delay = VacationBypassing Zones = RestoreQuick Arm Restoring ZonesBurglar Alarm Activated What To Do When You Come HomeWhat Happens When the Alarm is Activated #=GOTOFire Alarm Activated Gas Alarm ActivatedEmergency Keys Duress Code Entered or Duress Alarm Activated Alarm ResetAlarm Cancel Trouble Indications Master CodeArea Arming Panic SwitchesDuress Code Manager CodeGoto Area Testing Your System Control Control CommandsALC Switch Modules ModulesHouse Codes Unit NumbersScrolling Through Names Controlling Units Dimming and BrighteningLighting Level Timed Commands Ramp CommandScene Command Compose Controlling Outputs Status of a UnitInternal Flags All On / OffLeviton Scene Control ScenesButtons Temperature Control HMS ThermostatsIf hold mode is On, Hold is shown Outdoor Temperature Temperature AlarmsFreeze Alarms Temperature Control of AppliancesStatus Through Tstat Mode Auto FAN Auto Show EventsMessages Clear Text MessagesLog Message MessageShow Message Clear MessagePhone Message Send Message Pro-LinkIn-House Phones Telephone ControlTelephone Interface Remote PhonesPhone Access Denied Remote Lockout Alternate MethodMain Menu Security TemperatureControl ButtonWhen the HMS Communicating Thermostat is entered EventsMessage Playing and Recording a Message Playing and Recording a Custom PhraseEmergency Dial-Out Good-ByePanic Button over the Phone # # # # # # Digital DialerVoice Dialer How the HMS 1100 Voice Dialer WorksWhat the HMS 1100 Voice Dialer Does PC Access What You Hear If Your HMS 1100 Calls YouEntering the Code Controller IP Address, Port Number, and Encryption Key Connecting to Network via PC AccessBuilt-In Ethernet Port HMS 1100 Ethernet ConnectionsLocal Network Dynamic DNSLocal / Wide Area Network Setup Configuration and Advanced Control Programming ACPSet Up Codes Set Up Time Duress CodeAdvanced Control Programming ACP = Add Programs= Show Programs Otherwise, a help screen is displayed Edit Programs = Delete All ProgramsEdit Programs When Times ProgramsControl Unit Event / ALC Switch Press Event Buttons Security Mode Event ButtonsButton and Event Programs Zone Event Buttons Alarm Event Buttons All On/Off Event ButtonsEvent Buttons Miscellaneous Event Buttons Message Event Buttons Pro-LinkEdit Program Command Program Control CommandsProgram Security Commands Program Temperature Commands Program Button CommandsProgram All On / All Off Commands Program Message CommandsProgram Control Conditions Program Security Mode ConditionsEdit Program Condition Program Zone ConditionsProgram Time Clock Conditions Program Other ConditionsSet Up Dial Dial Out Number Dial Out NumbersDial Order Set Up Arming Entry DelayExit Delay Set up Miscellaneous Format Number Description House Codes 2-16 X-10 All Off Latitude, Longitude, and Time Zone Zone NameDaylight Savings Controller IP Address Controller Port NumberSet Up Names Encryption KeySet Up Voice Set Up AddressUnderwriters Laboratories Requirements Fire Escape PlanningFederal Communication Commission Notice Canadian Industry Canada Notice If YOU have Trouble with Your PhonesAppendix a Dial OUT Planner HMS 1100 Voice Dial-Out PlannerInstructions to Called Party Press 9. The system will say Good-bye and hang upAppendix B Text Description Character Codes Code CharAppendix C Voice Description Codes Code DescriptionFall Online Vault Page Page OnQTechnologies,Inc