On-Q/Legrand HMS 1100 owner manual Timed Commands, Ramp Command, Scene Command Compose

Page 28

The console will beep and the lighting level will be adjusted. The top line of the console display will read:

Entry Lights LVL 65

Ramp Command

When ALC Switch Modules are being used, it is possible to ramp the lighting level of an ALC Dimmer Switch to a new level at a selectable ramp rate. X-10 compatible switches and Compose lighting does not respond to the Ramp command.

Press the 5 (RAMP) key to select the ramp command. The keypad will then prompt you for the desired ramp rate:

ENTER RATE:

MINUTES (1-99) #=H/M/S

The rate specifies the time it takes the switch to go from full off to full on, or from full on to full off. Thus a level change from full off to 50% on will take half the time specified.

Before any digits are entered, the ' # ' key may be used to switch between specifying the rate in minutes, seconds, and hours. After you choose between minutes, seconds, and hours, enter the rate (2-99 seconds, 1-99 minutes, or 1-10 hours).

Next, enter a number (0-100) to indicate the final lighting level (intensity) desired.

LIGHTING LEVEL:

0-100%:

The keypad will beep and the lighting level will be adjusted. The keypad display top line will read:

Entry Lights 40% AT 1H

Scene Command (Compose)

If Compose lighting switches are part of your installation, the Scene (SCN) command is used to set a group of lights to predefined lighting levels. There is an Off command, an On command, and 12 lighting scenes for each group of Compose lighting switches.

SCENE:

0=OFF 1=ON 2-13=A-L

Enter 0, followed by the ' # ' key, to turn the lights that are part of the selected group off. Enter 1, followed by the ' # ' key, to set the lights that are part of the selected group to predefined lighting levels.

To set the lights in the selected group to a predefined scene, enter the Scene number 2-13 (which corresponds to Scene A-L, respectively), followed by the ' # ' key. All lights that are part of the selected group are set to the predefined lighting levels for the selected Scene.

Timed Commands

The timed commands allow a units to be turned on or off for a specified period of time. The unit may be turned On for 1-99 (minutes or seconds), or 1-18 hours, then Off; or turned Off for 1-99 (minutes or seconds) or 1-18 hours, then On.

X-10 units (1-16) may also be dimmed or brightened for a specified period of time. The unit may be dimmed (1-9) steps for 1-99 (minutes or seconds), or 1-18 hours, then brightened back to its previous level; or brightened (1-9) steps for 1-99 (minutes or seconds), or 1-18 hours, then dimmed back to its previous level.

To enter a timed command, you must first enter the unit that you want to control. From the control menu, enter the unit number (or scroll to it using the arrow keys), then press the ' # ' key.

To enter a time, press the 9 (TIM) key. Before any digits are entered, the ' # ' key may be used to switch between minutes, seconds, and hours. After you choose, enter a time (1-99 for seconds & minutes, and 1-18 for hours). Once the time is entered, the control menu is redisplayed with the specified times shown.

Page 20

Page 27 Page 29
Image 28
Page 27 Page 29
Contents HMS Page Contents Control Telephone Control Page Underwriters Laboratories Requirements Page Introduction Underwriters Laboratories UL ListingOverall Description Console OperationNormal Top-Level Display Display MenusError Beeps Main MenuTrouble Beeps To silence the beeper, press the * keyHMS 1100 Maintenance CancelAreas Confirmation BeepDisarming the Security System and Silencing Alarms Security System OperationArming the Security System = OFFUsing Shortcut Keys = Night DLY Night Delay= Night = Vacation= Restore Quick ArmBypassing Zones Restoring ZonesWhat To Do When You Come Home What Happens When the Alarm is ActivatedBurglar Alarm Activated #=GOTOGas Alarm Activated Fire Alarm ActivatedEmergency Keys Alarm Reset Duress Code Entered or Duress Alarm ActivatedAlarm Cancel Trouble Indications Master CodePanic Switches Duress CodeArea Arming Manager CodeGoto Area Testing Your System Control Commands ALC Switch ModulesControl ModulesHouse Codes Unit NumbersScrolling Through Names Dimming and Brightening Controlling UnitsLighting Level Ramp Command Timed CommandsScene Command Compose Status of a Unit Internal FlagsControlling Outputs All On / OffLeviton Scene Control ScenesButtons Temperature Control HMS ThermostatsIf hold mode is On, Hold is shown Temperature Alarms Freeze AlarmsOutdoor Temperature Temperature Control of AppliancesStatus Through Tstat Mode Auto FAN Auto Show EventsMessages Clear Text MessagesMessage Show MessageLog Message Clear MessagePhone Message Send Message Pro-LinkTelephone Control Telephone InterfaceIn-House Phones Remote PhonesAlternate Method Phone Access Denied Remote LockoutMain Menu Temperature ControlSecurity ButtonEvents When the HMS Communicating Thermostat is enteredMessage Playing and Recording a Message Playing and Recording a Custom PhraseGood-Bye Panic Button over the Phone # # # # # #Emergency Dial-Out Digital DialerHow the HMS 1100 Voice Dialer Works Voice DialerWhat the HMS 1100 Voice Dialer Does What You Hear If Your HMS 1100 Calls You PC AccessEntering the Code Connecting to Network via PC Access Built-In Ethernet PortController IP Address, Port Number, and Encryption Key HMS 1100 Ethernet ConnectionsLocal Network Dynamic DNSLocal / Wide Area Network Configuration and Advanced Control Programming ACP SetupSet Up Codes Set Up Time Duress Code= Add Programs Advanced Control Programming ACP= Show Programs Otherwise, a help screen is displayed Edit Programs = Delete All ProgramsEdit Programs When Times ProgramsSecurity Mode Event Buttons Control Unit Event / ALC Switch Press Event ButtonsButton and Event Programs Zone Event Buttons All On/Off Event Buttons Alarm Event ButtonsEvent Buttons Miscellaneous Event Buttons Message Event Buttons Pro-LinkProgram Control Commands Edit Program CommandProgram Security Commands Program Button Commands Program All On / All Off CommandsProgram Temperature Commands Program Message CommandsProgram Security Mode Conditions Edit Program ConditionProgram Control Conditions Program Zone ConditionsProgram Time Clock Conditions Program Other ConditionsSet Up Dial Dial Out Numbers Dial Out NumberDial Order Entry Delay Set Up ArmingExit Delay Set up Miscellaneous Format Number Description House Codes 2-16 X-10 All Off Zone Name Latitude, Longitude, and Time ZoneDaylight Savings Controller IP Address Controller Port NumberSet Up Names Encryption KeySet Up Voice Set Up AddressUnderwriters Laboratories Requirements Fire Escape PlanningFederal Communication Commission Notice Canadian Industry Canada Notice If YOU have Trouble with Your PhonesAppendix a Dial OUT Planner HMS 1100 Voice Dial-Out PlannerInstructions to Called Party Press 9. The system will say Good-bye and hang upAppendix B Text Description Character Codes Code CharAppendix C Voice Description Codes Code DescriptionFall Online Vault Page Page OnQTechnologies,Inc
Top Page Image Contents