On-Q/Legrand HMS 1100 Temperature Alarms, Humidity, Freeze Alarms, Outdoor Temperature

Page 34

For a heat or cool thermostat, the status shows the current temperature, the temperature setpoint, whether hold mode is on, the system mode, and the fan on/auto selection.

Upstairs

TEMP: 71

HEAT: 70

↓

Upstairs

FAN: AUTO ↑

MODE: HEAT

Freeze Alarms

Thermostats and Temperature Sensors can also be used to report potential freeze conditions before damage to pipes and appliances can occur. An alarm is activated when any Thermostat or Temperature Sensor detects a temperature below 40 degrees. The alarm will not clear until the temperature exceeds 45 degrees.

When the alarm is initiated, the console beeper will be turned on and an alarm dial-out sequence will be initiated after the normal dial-out delay. Both voice and digital communicator dial-outs may be used. The voice dial-out will follow the Dial Order as specified in Set Up Dial. The digital communicator will report the Freeze Alarm Code to the Central Station.

The sounder is not activated for freeze alarms (this feature must be activated by your installer).

Outdoor Temperature

HMS Outdoor Temperature Sensors are available. Outdoor Temperature Sensors may be mounted outdoors to read the outdoor temperature. The outdoor temperature will not generate freeze alarms.

Outdoor temperature zones have a High and Low temperature associated with them that can be used for control purposes. An example of this is to program the system to turn on the bathroom heat if the outdoor temp goes below 45 degrees.

Temperature Control of Appliances

You can control appliances connected to X-10 and ALC modules (such as a ceiling fan) using Advanced Control Programming (ACP) of the HMS 1100. For example, the ceiling fan can be programmed to come on if the temperature goes above the High temperature.

High and Low setpoints for temperature zones are set in the system. On/Off control of the ceiling fan is done from the 1 (CONTROL) menu. Use the ceiling fan's unit number to turn it On or Off. The Temperature Sensor and the ceiling fan are linked together by an event button program.

Temperature Alarms

Temperature Sensors can be used to signal that a temperature (in a special room, like a greenhouse or wine cooler) has gotten too high or too low. If the temperature in this zone goes above the High setpoint or below the Low setpoint, the console beeper is activated (inside and outside sirens are not activated) and the central station and/or voice dialer is called.

Use the zone number that the Temperature Sensor is connected to in place of the unit number.

NOTE: Setting a High or Low temperature to 0 takes it out of service.

Humidity

The Model 363443-05 Indoor/Outdoor Temperature and Humidity Sensor is used for sensing indoors temperature and/or reporting the relative humidity from 0 to 100 percent or for sensing the outdoor temperature and/or reporting the outdoor relative humidity.

High and low humidity limits can be set for taking action (i.e. turning on the bathroom vent fan, running a/c in de-humidification mode, turning on humidifier in heating mode, etc.) or reporting high or low humidity conditions in homes, greenhouses, wine cellars, coolers, humidors, etc. Controlling humidity is particularly helpful in combating the growth of mold in vulnerable areas of the home, such as bathrooms, basements, attics, etc.

Page 26

Page 33 Page 35
Image 34
Page 33 Page 35
Contents HMS Page Contents Control Telephone Control Page Underwriters Laboratories Requirements Page Introduction Underwriters Laboratories UL ListingOverall Description Console OperationNormal Top-Level Display Display MenusTrouble Beeps Error BeepsMain Menu To silence the beeper, press the * keyAreas HMS 1100 MaintenanceCancel Confirmation BeepArming the Security System Disarming the Security System and Silencing AlarmsSecurity System Operation = OFF= Night Using Shortcut Keys= Night DLY Night Delay = VacationBypassing Zones = RestoreQuick Arm Restoring ZonesBurglar Alarm Activated What To Do When You Come HomeWhat Happens When the Alarm is Activated #=GOTOGas Alarm Activated Fire Alarm ActivatedEmergency Keys Alarm Reset Duress Code Entered or Duress Alarm ActivatedAlarm Cancel Trouble Indications Master CodeArea Arming Panic SwitchesDuress Code Manager CodeGoto Area Testing Your System Control Control CommandsALC Switch Modules ModulesHouse Codes Unit NumbersScrolling Through Names Dimming and Brightening Controlling UnitsLighting Level Ramp Command Timed CommandsScene Command Compose Controlling Outputs Status of a UnitInternal Flags All On / OffLeviton Scene Control ScenesButtons Temperature Control HMS ThermostatsIf hold mode is On, Hold is shown Outdoor Temperature Temperature AlarmsFreeze Alarms Temperature Control of AppliancesStatus Through Tstat Mode Auto FAN Auto Show EventsMessages Clear Text MessagesLog Message MessageShow Message Clear MessagePhone Message Send Message Pro-LinkIn-House Phones Telephone ControlTelephone Interface Remote PhonesAlternate Method Phone Access Denied Remote LockoutMain Menu Security TemperatureControl ButtonEvents When the HMS Communicating Thermostat is enteredMessage Playing and Recording a Message Playing and Recording a Custom PhraseEmergency Dial-Out Good-ByePanic Button over the Phone # # # # # # Digital DialerHow the HMS 1100 Voice Dialer Works Voice DialerWhat the HMS 1100 Voice Dialer Does What You Hear If Your HMS 1100 Calls You PC AccessEntering the Code Controller IP Address, Port Number, and Encryption Key Connecting to Network via PC AccessBuilt-In Ethernet Port HMS 1100 Ethernet ConnectionsLocal Network Dynamic DNSLocal / Wide Area Network Configuration and Advanced Control Programming ACP SetupSet Up Codes Set Up Time Duress Code= Add Programs Advanced Control Programming ACP= Show Programs Otherwise, a help screen is displayed Edit Programs = Delete All ProgramsEdit Programs When Times ProgramsSecurity Mode Event Buttons Control Unit Event / ALC Switch Press Event ButtonsButton and Event Programs Zone Event Buttons All On/Off Event Buttons Alarm Event ButtonsEvent Buttons Miscellaneous Event Buttons Message Event Buttons Pro-LinkProgram Control Commands Edit Program CommandProgram Security Commands Program Temperature Commands Program Button CommandsProgram All On / All Off Commands Program Message CommandsProgram Control Conditions Program Security Mode ConditionsEdit Program Condition Program Zone ConditionsProgram Time Clock Conditions Program Other ConditionsSet Up Dial Dial Out Numbers Dial Out NumberDial Order Entry Delay Set Up ArmingExit Delay Set up Miscellaneous Format Number Description House Codes 2-16 X-10 All Off Zone Name Latitude, Longitude, and Time ZoneDaylight Savings Controller IP Address Controller Port NumberSet Up Names Encryption KeySet Up Voice Set Up AddressUnderwriters Laboratories Requirements Fire Escape PlanningFederal Communication Commission Notice Canadian Industry Canada Notice If YOU have Trouble with Your PhonesAppendix a Dial OUT Planner HMS 1100 Voice Dial-Out PlannerInstructions to Called Party Press 9. The system will say Good-bye and hang upAppendix B Text Description Character Codes Code CharAppendix C Voice Description Codes Code DescriptionFall Online Vault Page Page OnQTechnologies,Inc
Top Page Image Contents