Harman Stove Company P35I owner manual Inspect / Clean Hopper, By User

Page 32
6.Inspect / Clean Hopper

P35i Fireplace Insert

d. Un-latch and remove the ash pan. Dispose of the ashes in a metal container with a tight fitting lid.

e. Remove the two (2) corner cleanout covers by re- moving the wing-screws (one per).

f. Brush or vacuum the remaining ash from the fire- box.

g. Guide the vacuum hose upward into the exhaust passage in the right rear corner of the firebox.

Vacuum or brush exhaust passage

k. With this cover removed, you can vacuum the

paddle fan and the inside of the chamber. Be careful not to bend the blades on the paddle fan.

l. Before reinstalling the access cover, make sure the

insulation between the two layers is in tact.

h. You can now return all pieces inside the firebox and close the door.

i. Release the spring latches and slide the insert body out onto the hearth or onto the service rail kit, if pur- chased.

j. Remove the exhaust chamber access cover on the right rear of the insert.

6.Inspect / Clean Hopper

Frequency: Whenever run to empty

By: User

Whenever the hopper is empty, inspect and remove any large amounts of sawdust or fines. Although this finer material will mostly feed through with the fuel, large quantities of sawdust may restrict feeder flow.

32 Pellets or Corn/Pellet Mixture Only

3-90-775

Save These Instructions

Image 32
Contents Discard SAVE THESE INSTRUCTIONSModel Installed, a House Fire May Result TABLE OF CONTENTS E. BTU & Efficiency Specifications C. Glass Specifications1Listing and Code Approvals A. Appliance CertificationSPECIAL NOTE 2Special Warnings and Notes3Getting Started A. Design, Installation & Location ConsiderationsB. Fire Safety C. Component Locations P35i Fireplace InsertHopper Lid Latch GlassD. Pre- Use Check List Fire Risk4Dimensions & Clearances A. Appliance Dimensions60.96 cm P35i Fireplace InsertB. Clearances To Combustibles D. Minimum Opening for MasonryMasonry or Manufactured Fireplace and Manufactured FireplacesF. Factory-BuiltFireplace Installation Vent Information A. Vent Termination RequirementsB. Avoiding Smoke and Odors Negative Pressure, Shut-down,and Power FailureVent Configurations Outside AirWARNING! RISK OF INJURY OR PROPERTY DAMAGE C.Venting Requirements and RestrictionsWARNING! RISK OF FIRE Sealing Plate D. Existing Fireplace InstallationNon-combustible Insulation Vent pipe seams must be accessible F.Optional Zero Clearance Cabinet InstallationE. Existing Fireplace, Rear Vent A. Mobile Home Installation 6Mobile Home7Appliance Set-Up A. Outside Air AttachmentB. Installing the Surround C. Routing the Power CordD. Securing the Mounting Frame E. Attaching the VentingH. Room Sensor Installation F.Installing the Body into the Mounting FrameG. Control Board Installation J. Optional Trim Kit- #1-00-00775 K. Service Rail Kit- #1-00-774125I. Optional Log Kit A. Fire Safety OperatingInstructions B. Fuel and Fuel Storage2. Circuit Board C. General Operating Information1. ESP Exhaust Sensing Probe a. Feed Rate Adjustment d. Blower Speed Adjustmente. Igniter Mode Switch b. Mode SelectionF. Starting a Fire - MANUAL E. Draft Test ProcedureD. Before Your First Fire G. Starting a Fire - AUTOMATIC H. Maintaining the FireI. Relaxation Mode J. Shut-DownTroubleshooting Error MessageSymptom Possible CauseService & Maintenance A. Shut-downProcedureB. Quick Reference Maintenance Chart CAUTION! SHOCK AND SMOKE HAZARDC.General Maintenance Procedures 5.Cleaning Area Beneath Burn Pot Grate 5.Cleaning Heat Exchanger & ExhaustWARNING! RISK OF FIRE By User6.Inspect / Clean Hopper By User7.Cleaning the Door Glass By User8.Venting and Chimney System Soot and Fly Ash Formation & Need for RemovalD. Motors and Components P35i Fireplace InsertHopper Lid Latch Glass3.ESP- Exhaust Sensing Probe 1.Feed Motor2.Combustion Blower 4.Distribution Blower 5.Feeder Body6.Igniter P35i Fireplace Insert 11Reference MaterialsPLUG PIN 11 WHITE Addendum P35i Fireplace InsertP35i Pellet Insert Pellet Insert9 10 11 12 13 4 5 6#4 Surround Assembly P35i Pellet InsertDescription COMMENTSP35i Pellet Insert DescriptionCOMMENTS PART NUMBERP35i Pellet Insert DescriptionCOMMENTS PART NUMBERD. Custom Size Surround P35i Custom Surround Part #: 1-00-774221-SPLLIMITED LIFETIME WARRANTY WARRANTY COVERAGEWARRANTY PERIOD Hearth & Home Technologies IncWARRANTY CONDITIONS WARRANTY EXCLUSIONSThis warranty is void if LIMITATIONS OF LIABILITYService & Maintenance Log Date Of ServiceDescription Of Service P35i Fireplace InsertProudly Printed On 100% Recycled Paper