Harman Stove Company P35I owner manual 4Dimensions & Clearances, A. Appliance Dimensions, 60.96 cm

Page 9

P35i Fireplace Insert

4Dimensions & Clearances

A. Appliance Dimensions

19.5”

49.53 cm Hopper

23.5”

59.69 cm Hopper

		B
	24”
	60.96 cm
	Standard Surround	Oversize Surround
	# 1-00-774221	# 1-00-774250
A:	40" (101.6 cm)	46" (116.8 cm)
B:	31" (78.74 cm)	34" (86.36 cm)

22”

55.88 cm

14” 35.56 cm

2”

5.08 cm

8”

10”

20.32 cm

25.4 cm

Save These Instructions

3-90-775

Pellets or Corn/Pellet Mixture Only

Image 9

Contents SAVE THESE INSTRUCTIONS ModelDiscard Installed, a House Fire May Result TABLE OF CONTENTS C. Glass Specifications E. BTU & Efficiency Specifications1Listing and Code Approvals A. Appliance Certification2Special Warnings and Notes SPECIAL NOTEA. Design, Installation & Location Considerations B. Fire Safety3Getting Started P35i Fireplace Insert C. Component LocationsHopper Lid Latch GlassFire Risk D. Pre- Use Check ListA. Appliance Dimensions 4Dimensions & Clearances60.96 cm P35i Fireplace InsertD. Minimum Opening for Masonry B. Clearances To CombustiblesMasonry or Manufactured Fireplace and Manufactured FireplacesF. Factory-BuiltFireplace Installation A. Vent Termination Requirements Vent InformationNegative Pressure, Shut-down,and Power Failure B. Avoiding Smoke and OdorsVent Configurations Outside AirC.Venting Requirements and Restrictions WARNING! RISK OF FIREWARNING! RISK OF INJURY OR PROPERTY DAMAGE D. Existing Fireplace Installation Non-combustible InsulationSealing Plate F.Optional Zero Clearance Cabinet Installation E. Existing Fireplace, Rear VentVent pipe seams must be accessible 6Mobile Home A. Mobile Home InstallationA. Outside Air Attachment 7Appliance Set-UpC. Routing the Power Cord B. Installing the SurroundE. Attaching the Venting D. Securing the Mounting FrameF.Installing the Body into the Mounting Frame G. Control Board InstallationH. Room Sensor Installation K. Service Rail Kit- #1-00-774125 I. Optional Log KitJ. Optional Trim Kit- #1-00-00775 Operating A. Fire SafetyInstructions B. Fuel and Fuel StorageC. General Operating Information 1. ESP Exhaust Sensing Probe2. Circuit Board d. Blower Speed Adjustment a. Feed Rate Adjustmente. Igniter Mode Switch b. Mode SelectionE. Draft Test Procedure D. Before Your First FireF. Starting a Fire - MANUAL H. Maintaining the Fire G. Starting a Fire - AUTOMATICI. Relaxation Mode J. Shut-DownError Message TroubleshootingSymptom Possible CauseA. Shut-downProcedure Service & MaintenanceB. Quick Reference Maintenance Chart CAUTION! SHOCK AND SMOKE HAZARDC.General Maintenance Procedures 5.Cleaning Heat Exchanger & Exhaust 5.Cleaning Area Beneath Burn Pot GrateWARNING! RISK OF FIRE By UserBy User 6.Inspect / Clean HopperBy User 7.Cleaning the Door Glass8.Venting and Chimney System Soot and Fly Ash Formation & Need for RemovalP35i Fireplace Insert D. Motors and ComponentsHopper Lid Latch Glass1.Feed Motor 2.Combustion Blower3.ESP- Exhaust Sensing Probe 5.Feeder Body 4.Distribution Blower6.Igniter 11Reference Materials PLUG PIN 11 WHITEP35i Fireplace Insert P35i Fireplace Insert AddendumPellet Insert P35i Pellet Insert9 10 11 12 13 4 5 6P35i Pellet Insert #4 Surround AssemblyDescription COMMENTSDescription P35i Pellet InsertCOMMENTS PART NUMBERDescription P35i Pellet InsertCOMMENTS PART NUMBERP35i Custom Surround Part #: 1-00-774221-SPL D. Custom Size SurroundWARRANTY COVERAGE LIMITED LIFETIME WARRANTYWARRANTY PERIOD Hearth & Home Technologies IncWARRANTY EXCLUSIONS WARRANTY CONDITIONSThis warranty is void if LIMITATIONS OF LIABILITYDate Of Service Service & Maintenance LogDescription Of Service P35i Fireplace InsertProudly Printed On 100% Recycled Paper