Harman Stove Company P35I P35i Pellet Insert, 9 10 11 12 13, 4 5 6, 3 27, 23.5 in1-70-774235-1

Page 40
P35i Pellet Insert

Service Parts

P35i Pellet Insert

 

 

 

 

 

 

Pellet Insert

Beginning Manufacturing Date: July 2010

 

Ending Manufacturing Date: Active

 

 

 

(23.5 in)1-70-774235-1
(Black), (19.5 in)1-70-774195-1 (Black),

 

 

 

 

 

Ending Manufacturing Date: June 2011

 

 

(23.5 in) 1-70-774235-2
(Charcoal), 1-70-774235-3 (Goldenfire))

 

(19.5 in) 1-70-774195-2
(Charcoal), 1-70-774195-3 (Goldenfire))

 

 

 

 

 

 

9

10

11

12

13

14

15

7

8

4

5

6

26

3

27

1

2

25

16

17

19 20

24

22 23

21

18

Part number list on following page.

08/11

Image 40
Contents Model SAVE THESE INSTRUCTIONSDiscard Installed, a House Fire May Result TABLE OF CONTENTS E. BTU & Efficiency Specifications C. Glass Specifications1Listing and Code Approvals A. Appliance CertificationSPECIAL NOTE 2Special Warnings and NotesB. Fire Safety A. Design, Installation & Location Considerations3Getting Started C. Component Locations P35i Fireplace InsertHopper Lid Latch GlassD. Pre- Use Check List Fire Risk4Dimensions & Clearances A. Appliance Dimensions60.96 cm P35i Fireplace InsertB. Clearances To Combustibles D. Minimum Opening for MasonryMasonry or Manufactured Fireplace and Manufactured FireplacesF. Factory-BuiltFireplace Installation Vent Information A. Vent Termination RequirementsB. Avoiding Smoke and Odors Negative Pressure, Shut-down,and Power FailureVent Configurations Outside AirWARNING! RISK OF FIRE C.Venting Requirements and RestrictionsWARNING! RISK OF INJURY OR PROPERTY DAMAGE Non-combustible Insulation D. Existing Fireplace InstallationSealing Plate E. Existing Fireplace, Rear Vent F.Optional Zero Clearance Cabinet InstallationVent pipe seams must be accessible A. Mobile Home Installation 6Mobile Home7Appliance Set-Up A. Outside Air AttachmentB. Installing the Surround C. Routing the Power CordD. Securing the Mounting Frame E. Attaching the VentingG. Control Board Installation F.Installing the Body into the Mounting FrameH. Room Sensor Installation I. Optional Log Kit K. Service Rail Kit- #1-00-774125J. Optional Trim Kit- #1-00-00775 A. Fire Safety OperatingInstructions B. Fuel and Fuel Storage1. ESP Exhaust Sensing Probe C. General Operating Information2. Circuit Board a. Feed Rate Adjustment d. Blower Speed Adjustmente. Igniter Mode Switch b. Mode SelectionD. Before Your First Fire E. Draft Test ProcedureF. Starting a Fire - MANUAL G. Starting a Fire - AUTOMATIC H. Maintaining the FireI. Relaxation Mode J. Shut-DownTroubleshooting Error MessageSymptom Possible CauseService & Maintenance A. Shut-downProcedureB. Quick Reference Maintenance Chart CAUTION! SHOCK AND SMOKE HAZARDC.General Maintenance Procedures 5.Cleaning Area Beneath Burn Pot Grate 5.Cleaning Heat Exchanger & ExhaustWARNING! RISK OF FIRE By User6.Inspect / Clean Hopper By User7.Cleaning the Door Glass By User8.Venting and Chimney System Soot and Fly Ash Formation & Need for RemovalD. Motors and Components P35i Fireplace InsertHopper Lid Latch Glass2.Combustion Blower 1.Feed Motor3.ESP- Exhaust Sensing Probe 4.Distribution Blower 5.Feeder Body6.Igniter PLUG PIN 11 WHITE 11Reference MaterialsP35i Fireplace Insert Addendum P35i Fireplace InsertP35i Pellet Insert Pellet Insert9 10 11 12 13 4 5 6#4 Surround Assembly P35i Pellet InsertDescription COMMENTSP35i Pellet Insert DescriptionCOMMENTS PART NUMBERP35i Pellet Insert DescriptionCOMMENTS PART NUMBERD. Custom Size Surround P35i Custom Surround Part #: 1-00-774221-SPLLIMITED LIFETIME WARRANTY WARRANTY COVERAGEWARRANTY PERIOD Hearth & Home Technologies IncWARRANTY CONDITIONS WARRANTY EXCLUSIONSThis warranty is void if LIMITATIONS OF LIABILITYService & Maintenance Log Date Of ServiceDescription Of Service P35i Fireplace InsertProudly Printed On 100% Recycled Paper