Harman Stove Company P35I D. Custom Size Surround, P35i Custom Surround Part #: 1-00-774221-SPL

Page 44

P35i Fireplace Insert

D. Custom Size Surround

This diagram shows the minimum dimensions of a custom fit surround panel, part number

1-00-774221-SPL. Note that arched surrounds can only be made flat. Therefore, the intake air slots, normally in the sides of the surround, are moved to the face. Rectangular surrounds can be made flat if desired, and they will also have the intake slots in the face.

P35i Custom Surround -

Part #: 1-00-774221-SPL

The top of the mounting frame must be covered at this point.

Rectangular- Minimum Height

2811/16"

729mm

Arched- Minimum Center Height

313/8"

797mm

Arched- Minimum Side Height

247/8"

632mm

Minimum Width- 40" 1016mm

44 Pellets or Corn/Pellet Mixture Only

3-90-775

Save These Instructions

Image 44

Contents Discard SAVE THESE INSTRUCTIONSModel Installed, a House Fire May Result TABLE OF CONTENTS E. BTU & Efficiency Specifications C. Glass Specifications1Listing and Code Approvals A. Appliance CertificationSPECIAL NOTE 2Special Warnings and Notes3Getting Started A. Design, Installation & Location ConsiderationsB. Fire Safety C. Component Locations P35i Fireplace InsertHopper Lid Latch GlassD. Pre- Use Check List Fire Risk4Dimensions & Clearances A. Appliance Dimensions60.96 cm P35i Fireplace InsertB. Clearances To Combustibles D. Minimum Opening for MasonryMasonry or Manufactured Fireplace and Manufactured FireplacesF. Factory-BuiltFireplace Installation Vent Information A. Vent Termination RequirementsB. Avoiding Smoke and Odors Negative Pressure, Shut-down,and Power FailureVent Configurations Outside AirWARNING! RISK OF INJURY OR PROPERTY DAMAGE C.Venting Requirements and RestrictionsWARNING! RISK OF FIRE Sealing Plate D. Existing Fireplace InstallationNon-combustible Insulation Vent pipe seams must be accessible F.Optional Zero Clearance Cabinet InstallationE. Existing Fireplace, Rear Vent A. Mobile Home Installation 6Mobile Home7Appliance Set-Up A. Outside Air AttachmentB. Installing the Surround C. Routing the Power CordD. Securing the Mounting Frame E. Attaching the VentingH. Room Sensor Installation F.Installing the Body into the Mounting FrameG. Control Board Installation J. Optional Trim Kit- #1-00-00775 K. Service Rail Kit- #1-00-774125I. Optional Log Kit A. Fire Safety OperatingInstructions B. Fuel and Fuel Storage2. Circuit Board C. General Operating Information1. ESP Exhaust Sensing Probe a. Feed Rate Adjustment d. Blower Speed Adjustmente. Igniter Mode Switch b. Mode SelectionF. Starting a Fire - MANUAL E. Draft Test ProcedureD. Before Your First Fire G. Starting a Fire - AUTOMATIC H. Maintaining the FireI. Relaxation Mode J. Shut-DownTroubleshooting Error MessageSymptom Possible CauseService & Maintenance A. Shut-downProcedureB. Quick Reference Maintenance Chart CAUTION! SHOCK AND SMOKE HAZARDC.General Maintenance Procedures 5.Cleaning Area Beneath Burn Pot Grate 5.Cleaning Heat Exchanger & ExhaustWARNING! RISK OF FIRE By User6.Inspect / Clean Hopper By User7.Cleaning the Door Glass By User8.Venting and Chimney System Soot and Fly Ash Formation & Need for RemovalD. Motors and Components P35i Fireplace InsertHopper Lid Latch Glass3.ESP- Exhaust Sensing Probe 1.Feed Motor2.Combustion Blower 4.Distribution Blower 5.Feeder Body6.Igniter P35i Fireplace Insert 11Reference MaterialsPLUG PIN 11 WHITE Addendum P35i Fireplace InsertP35i Pellet Insert Pellet Insert9 10 11 12 13 4 5 6#4 Surround Assembly P35i Pellet InsertDescription COMMENTSP35i Pellet Insert DescriptionCOMMENTS PART NUMBERP35i Pellet Insert DescriptionCOMMENTS PART NUMBERD. Custom Size Surround P35i Custom Surround Part #: 1-00-774221-SPLLIMITED LIFETIME WARRANTY WARRANTY COVERAGEWARRANTY PERIOD Hearth & Home Technologies IncWARRANTY CONDITIONS WARRANTY EXCLUSIONSThis warranty is void if LIMITATIONS OF LIABILITYService & Maintenance Log Date Of ServiceDescription Of Service P35i Fireplace InsertProudly Printed On 100% Recycled Paper