Harman Stove Company P35I owner manual D. Pre- Use Check List, Fire Risk

Page 8
D. Pre- Use Check List

P35i Fireplace Insert

D. Pre- Use Check List

1.

 

Place the appliance in a location near the

 

 

final installation and follow the procedures

 

 

below:

2.

 

Open the appliance and remove all articles

 

 

packed inside. Inspect all items for shipping

 

 

damage. Notify dealer of any missing or

 

 

damaged goods.

3.

 

All safety warnings have been read and

 

 

followed precisely.

4.

 

This Owner's Manual has been read in it's

 

 

entirety.

5.

 

Floor protection requirements have been

 

 

read and followed.

6.

 

The flue connector has been installed in

 

 

accordance with the instructions herein.

7.

 

The proper clearances from the appliance

 

 

and chimney connector to combustibles

 

 

have been met.

8.

 

The masonry chimney has been cleaned

 

 

and inspected by a professional, or the

 

 

factory built metal chimney is installed

 

 

according to the manufacturers instructions.

9.

 

The chimney meets the minimum height

 

 

requirements.

10.

 

All labels and hang tags have been removed

 

 

from the glass.

11.

 

All plated surfaces have been wiped clean,

 

 

if applicable.

12.

 

The room sensor and any additional cable

 

 

has been installed properly.

13.

 

A properly grounded electrical receptacle is

 

 

available within reach of the unit's power

 

 

cord.

14.

 

A good quality surge protector is highly

 

 

recommended to protect the electronics.

 

 

 

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

Do NOT install damaged components.

Do NOT install incomplete components.

Do NOT install substitute components.

Report damaged parts to dealer.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

Installation and use of any damaged appliance.

Modification of the appliance.

Installation other than as instructed by Hearth & Home Technologies.

Installation of substitute materials or replacement parts not approved by Hearth & Home Technologies

Operating appliance without fully assembling all components.

Do NOT Overfire.

Or any such action that may cause a fire hazard.

8 Pellets or Corn/Pellet Mixture Only

3-90-775

Save These Instructions

Image 8
Contents Discard SAVE THESE INSTRUCTIONSModel Installed, a House Fire May Result TABLE OF CONTENTS E. BTU & Efficiency Specifications C. Glass Specifications1Listing and Code Approvals A. Appliance CertificationSPECIAL NOTE 2Special Warnings and Notes3Getting Started A. Design, Installation & Location ConsiderationsB. Fire Safety C. Component Locations P35i Fireplace InsertHopper Lid Latch GlassD. Pre- Use Check List Fire Risk4Dimensions & Clearances A. Appliance Dimensions60.96 cm P35i Fireplace InsertB. Clearances To Combustibles D. Minimum Opening for MasonryMasonry or Manufactured Fireplace and Manufactured FireplacesF. Factory-BuiltFireplace Installation Vent Information A. Vent Termination RequirementsB. Avoiding Smoke and Odors Negative Pressure, Shut-down,and Power FailureVent Configurations Outside AirWARNING! RISK OF INJURY OR PROPERTY DAMAGE C.Venting Requirements and RestrictionsWARNING! RISK OF FIRE Sealing Plate D. Existing Fireplace InstallationNon-combustible Insulation Vent pipe seams must be accessible F.Optional Zero Clearance Cabinet InstallationE. Existing Fireplace, Rear Vent A. Mobile Home Installation 6Mobile Home7Appliance Set-Up A. Outside Air AttachmentB. Installing the Surround C. Routing the Power CordD. Securing the Mounting Frame E. Attaching the VentingH. Room Sensor Installation F.Installing the Body into the Mounting FrameG. Control Board Installation J. Optional Trim Kit- #1-00-00775 K. Service Rail Kit- #1-00-774125I. Optional Log Kit A. Fire Safety OperatingInstructions B. Fuel and Fuel Storage2. Circuit Board C. General Operating Information1. ESP Exhaust Sensing Probe a. Feed Rate Adjustment d. Blower Speed Adjustmente. Igniter Mode Switch b. Mode SelectionF. Starting a Fire - MANUAL E. Draft Test ProcedureD. Before Your First Fire G. Starting a Fire - AUTOMATIC H. Maintaining the FireI. Relaxation Mode J. Shut-DownTroubleshooting Error MessageSymptom Possible CauseService & Maintenance A. Shut-downProcedureB. Quick Reference Maintenance Chart CAUTION! SHOCK AND SMOKE HAZARDC.General Maintenance Procedures 5.Cleaning Area Beneath Burn Pot Grate 5.Cleaning Heat Exchanger & ExhaustWARNING! RISK OF FIRE By User6.Inspect / Clean Hopper By User7.Cleaning the Door Glass By User8.Venting and Chimney System Soot and Fly Ash Formation & Need for RemovalD. Motors and Components P35i Fireplace InsertHopper Lid Latch Glass3.ESP- Exhaust Sensing Probe 1.Feed Motor2.Combustion Blower 4.Distribution Blower 5.Feeder Body6.Igniter P35i Fireplace Insert 11Reference MaterialsPLUG PIN 11 WHITE Addendum P35i Fireplace InsertP35i Pellet Insert Pellet Insert9 10 11 12 13 4 5 6#4 Surround Assembly P35i Pellet InsertDescription COMMENTSP35i Pellet Insert DescriptionCOMMENTS PART NUMBERP35i Pellet Insert DescriptionCOMMENTS PART NUMBERD. Custom Size Surround P35i Custom Surround Part #: 1-00-774221-SPLLIMITED LIFETIME WARRANTY WARRANTY COVERAGEWARRANTY PERIOD Hearth & Home Technologies IncWARRANTY CONDITIONS WARRANTY EXCLUSIONSThis warranty is void if LIMITATIONS OF LIABILITYService & Maintenance Log Date Of ServiceDescription Of Service P35i Fireplace InsertProudly Printed On 100% Recycled Paper