Heat & Glo LifeStyle CERONA-36, CERONA-42 owner manual Mantel Projections, 724 425 406 279

Page 9

D. Mantel Projections

		CEILING
	A						1 in.
	COMBUSTIBLE					TYPICAL
	FACING MATERIAL
						12"
						11"
					10"
	FIREPLACE HEADER				9"
					8"		E
					7"		E
				6"			MINIMUM
				5"		FROM TOP OF ARCH
				4"		FROM TOP OF ARCH
				4"		OPENING TO CEILING
				3"		OPENING TO CEILING
				2"
	B			1"
	B
	NON-COMBUSTIBLE
	FACING MATERIAL		C		D
				MINIMUM
				FROM TOP OF ARCH
				OPENING TO FIRST
				MANTEL PROJECTION
				TOP OF ARCH OPENING
			A	B	C	D	E
	Cerona-36	in.	32-1/4	16-3/4	16	11	49
	Cerona-36	mm	819	425	406	279	1245
		mm	819	425	406	279	1245
	Cerona-42	in.	28-1/2	16-3/4	16	11	45-1/4
	Cerona-42	mm	724	425	406	279	1149
		mm	724	425	406	279	1149

Figure 3.3 Clearances to mantels or other combustibles above appliance

COMBUSTIBLE

SHEATHING

CLEARANCE
TO CEILING	CEILING
	CEILING
	B MINIMUM

A

NON-COMBUSTIBLE

FACING MATERIAL

IN SHADED AREAS

FIREPLACE

ARCH OPENING

1 in.

(25)

C

BOTTOM OF FIREPLACE

TO BOTTOM OF

NON-COMBUSTIBLE

FACING MATERIAL

		A	B	C
Cerona-36	in.	49	16-3/4	43-5/8
Cerona-36	mm	1245	425	1108
Cerona-42	in.	45-1/4	16-3/4	50-5/8
Cerona-42	mm	1149	425	1286

Figure 3.5

TOP VIEW

MANTEL LEG OR WALL PROJECTIONS

INTERIOR WALL

B

Note: If using the Apollo Mantel System, the appliance must be raised 1-1/4 in. from ﬂoor.

A

If A minimum is _____, then B maximum is ______.

	A	in.	1	2	3	4	5	6	7	8	9	10	11	12

		mm	25	51	76	102	127	152	178	203	229	254	279	305
		mm	25	51	76	102	127	152	178	203	229	254	279	305

	B	in.	1	2	3	4	5	6	7	8	9	10	11	12

		mm	25	51	76	102	127	152	178	203	229	254	279	305
		mm	25	51	76	102	127	152	178	203	229	254	279	305

Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.)

Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. F • 04/08

9

Image 9

Contents

What to do if you smell gas ModelsModel Number Serial Number Homeowner Reference InformationTable of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsGetting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Read all of the instructions before starting the instaSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance Chase724 425 406 279 Mantel ProjectionsHearth Extension Hearth Extension DimensionsVent Termination Minimum Clearances Termination LocationsMinimum Clearances for Termination Alcove ApplicationsInstall Support Brackets To Install the Heat ShieldContinue Adding Vent Components Vent Table Key Vent Information and DiagramsUse of Elbows Measuring StandardsVent Diagrams Top Vent Horizontal Termination One ElbowTwo Elbows Top Vent Vertical Termination Straight up Vertical Venting Top Vent Horizontal Termination Three ElbowsV1 = 50 ft. Max .2 m 152 mm 914 mm 305 mm 610 mm 10 ft305 mm 610 mm 914 mm 10 ft Top Vent Horizontal Termination Two ElbowsPipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationInstalling the Ceiling Firestop Installing Attic ShieldVertical Penetration Framing Appliance Preparation Removing Non-combustible Facing Mate- rial AssemblyDiagram shows .2 the location of the nailing tabs Securing and Leveling the ApplianceProvided to secure the appliance to the framing members Complete Installation of Non-combustible Facing Material Installing Flue RestrictorsAssembly of Vent Sections Installing Vent PipeAttaching Vent to the Firebox Assembly Assembling Pipe SectionsAssembling DVP-12A Slip Sections Assembling Minimum Installations MI SectionsSecuring the Vent Sections Disassembly of Vent SectionsVertical Sections Horizontal SectionsInstalling the Horizontal Termination Cap Installing Heat Shield and Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Heat shield DVP-HSM-B must be usedﬂue of the pipe see Figure Installing Roof Flashing and Vertical Ter- mination Cap18 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm CollarGas Information Fuel Conversions Gas ConnectionGas Pressures High Altitude Installations Intelliﬁre Ignition System Wiring Recommendation for WireConnecting to the Appliance Optional Accessories RequirementsProperly grounded Not operate unlessJunction Box Detail Junction Box InstallationStep Finishing Non-combustible Facing Material Facing MaterialFinishing Material Thickness from 3/4 in. to 1-1/4 Finishing Material OptionsFinishing Material Thickness greater than 1-1/4 inch Mounting stone eye brow ATRIMSTONE-36, ATRIMSTONE-4210 Fireplace sitting on combustible surface Clean the Appliance Appliance SetupAccessories Ember PlacementPositioning the Logs Model Cerona-36 Log Assembly LOGS-Cerona36Heat & Glo Cerona-36, Cerona-42 2106-900 Rev. F 04/08 Model Cerona-42 Step Glass Assembly Air Shutter SettingGrilles and Trim Operating Instructions Before Lighting ApplianceThis appliance has an Intelliﬁre ignition system Final inspection by Lighting Appliance IPI IgnitionFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Intelliﬁre Ignition SystemSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksAppliance Dimension Diagram Reference MaterialsModel Cerona-36 Model Cerona-42 DVP vent components Vent Components DiagramsDVP-TRAP COOL-ADD Not for use with these models Log Set Assembly Service PartsPart number list on following At Depot Service Parts ListStocked IPI Valve AssemblyCERONA-42 Fan Kit GFK-160A Junction Box 4021-013 Box Paint Kit CERONA-42IPI Valve Assembly Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyContact Information

Related manuals

Manual 62 pages 22.54 Kb

Manual 1 pages 2.44 Kb