Desa SDVBNC, SDVBPC High Altitude Installation, Parts Lists for Venting Kits and Components

Page 19

VENTING INSTALLATION

Installation for Vertical Termination (Cont.) High Altitude Installation Parts List for Venting Kits and Components

19

VENTING INSTALLATION

Continued

Vertical Venting

V = 40' max.

Note: Install restrictor into 4" collar of burner system as shown.

Figure 39 - Vertical Venting Configuration With No Horizontal Run

HIGH ALTITUDE INSTALLATION

Your cast iron stove and direct-vent burner system has been CSA tested and approved for operation at altitudes in the USA from 0- 2000 ft. and in Canada from 0-4500 ft.

When installing this stove at an elevation above 2000 feet (in the USA), you may need to decrease the input rating by changing the existing burner orifice to a smaller size. Reduce input 4% for each 1000 feet above sea level. Check with your local gas company for proper orifice size identification and proper orifice for your location..

When installing this stove at an elevation above 4500 feet (in Canada), check with local authorities.

For assistance with any high altitude installation contact DESA’s Technical Service Department at 1-866-672-6040.

PARTS LISTS FOR VENTING KITS AND COMPONENTS

Number Description

VKG-47-K Ground Floor Vent Kit, Black

Includes: Horizontal Square Termination, 90° Elbow, 7"- 12" Adjustable Coaxial Pipe, 6" Pipe Adaptor, 12" Coaxial Pipe, Wall Firestop, Decorative Trim Plate and 18 Screws

VKB-47-K Basement Vent Kit

Includes: Horizontal Square Termination, 90° Elbow, 7"- 12" Adjustable Coaxial Pipe, 6" Pipe Adaptor, 4' Coaxial Pipe, Wall Firestop, Decorative Trim Plate and 18 Screws

VKS-47-K Snorkel Vent Kit

Includes: 36" Snorkel Termination, 90° Elbow, 7"-12" Adjustable Coaxial Pipe, 6" Pipe Adaptor, 4' Coaxial Pipe, Wall Firestop, Decorative Trim Plate and 18 Screws

VKR-47-K Roof Vent Kit

Includes:VerticalHighWindTermination,FlueRestrictor, 7"-12" Adjustable Coaxial Pipe, 6" Pipe Adaptor, 12" Coaxial Pipe, 4' Coaxial Pipe, Firestop Decorative Trim Plate, Roof Flashing, Storm Collar and 18 Screws

P-47-12-K 12" Black Coaxial Pipe (1 pk)

P-47-24-K 24" Black Coaxial Pipe (1 pk)

P-47-48-K 48" Black Coaxial Pipe (1 pk)

PA47-712-K 7"-12" Black Coaxial Pipe (1 pk)

P-47-6-K 6" Black Coaxial Pipe (1 pk)

E47-90-K 90° Elbow (1 pk)

E47-45-K 45° Elbow (1 pk)

PA-47-6-K 6" Adaptor Collar, Black (1 pk)

WS-47 Wall Strap (1 pk)

SC-47 Storm Collar (1 pk)

VT-47 Vertical Round Termination (1 pk)

WF-47 Wall Firestop (1 pk)

VR-47

Vertical Restrictor (1 pk)

FP-47

Firestop Plate (1 pk)

HTS-47

Horizontal Square Termination (1 pk)

CS-47

Cathedral Ceiling Support Box (1 pk)

RF-47-6

Roof Flashing 0 to 6/12 Pitch (1 pk)

RF-47-12

Roof Flashing 6/12 to 12/12 Pitch (1 pk)

S-47

Vinyl Siding Standoff (1 pk)

TP-47

Trim Plate, Black (1 pk)

HT-47

Horizontal Round Termination (1 pk)

ST-47-14

14" Snorkel Termination (1 pk)

ST-47-36

36" Snorkel Termination (1 pk)

For morevisit www..com

107304-01D

Image 19
Contents For Your Safety OWNER’S Operation and Installation ManualFor Your Safety What to do if YOU Smell GAS Safety Information Table of ContentsON/OFF Product IdentificationLocal Codes PRE-INSTALLATION Preparation Product FeaturesGlossary of Terms Cast Iron Stove and DIRECT-VENT Burner System Assembly PRE-INSTALLATION PreparationStove Body Assembly Removing Pallet Wood From The Bottom of The Stove Attaching Lower Stove Door Panel Installing Optional Blower Accessory Installing the Blower Installing DIRECT-VENT Burner System Into Stove BodySecurely in place before venting pipes are installed Installing Rear CoverLocation of Vent Termination General VentingGeneral Venting Installation Precautions Venting InstallationInstallation Planning Installing Vent System in a Chase Installation for Horizontal TerminationInstalling Horizontal Vent Cap Noncombustible Exterior Horizontal Venting Horizontal Termination ConfigurationsFlat Ceiling Installation Installation for Vertical TerminationVertical Termination Configurations Cathedral Ceiling InstallationVenting with Two Elbows Parts Lists for Venting Kits and Components High Altitude InstallationCheck GAS Type Stove and DIRECT-VENT Burner System InstallationInstalling GAS Piping to STOVE/ Burner System Location Installation Items NeededPressure Testing Gas Supply Piping System Connecting STOVE/BURNER System to GAS SupplyChecking GAS Connections Pressure Testing Burner System Gas Connections Installing Optional Wall Mount Switch GWMS2Installing Remote Receiver and 9-volt Alkaline Battery Installing Optional Wall Mounted Thermostat GWMT1REMOVING/REPLACING Glass Door Installing Remote ReceiverInstalling Log No Installing Log No Installing LOGS, Lava Rock and Glowing EmbersTo Turn OFF GAS To Appliance For Your Safety Read Before LightingOperating Stove with Burner System Lighting InstructionsGhrcta Series Operation Manual Lighting ProcedureOptional Remote Operation Thermostat Control OperationOperating Optional GWMT1 Wall Mounted Thermostat Operating Optional Blower AccessoryPilot Assembly Inspecting BurnersLogs Cleaning and MaintenanceGlass Door Pilot and BurnersObserved Problem Possible Cause TroubleshootingObserved Problem Possible Cause Remedy Gas leak. See Warning statement Parts Under Warranty SpecificationsWiring Diagram Replacement PartsSdvbnc Sdvbpc Illustrated Parts BreakdownKEY Sdvbnc Sdvbpc Description QTY Parts ListIndicates Color Suffix Designation Amity Stove Chassis SCIVFC* Series PSCIVFC* SeriesKEY Part Description QTY Service Hints Technical ServiceAccessories Owners Registration Form Postage Required 107304-01D Warranty Information