Vermont Casting 2100 installation instructions AppendixApproved Chimney Components

Page 41

WinterWarm Fireplace Insert or System

Appendix:Approved Chimney Components

	American Metal Products Ameri-Tec Model HS	Condensation Engineering Corp. Vitroliner HS-2100	GSW Building Product Co. Model SC	Metal Fab, Inc. Model TG	Security Chimneys, Ltd. Model ASHT	Selkirk Metalbestos Model SSII	Simpson Dura-vent Dura-Plus

Anchor/base plate	8HS-AP	8H-SP	JSC 8 AP	8TG AP	8 SP	8T-AP	9201
Starter	NA	NA	NA	NA	NA	NA	9216
	8HS-6	8H-SCS36	JSC 8 SA3	8TG 36	8 L3	8T-36	9206
	8HS-12	8H-SCS24	JSC 8 SA2	8TG 24	8 L2	8T-18	9219
Chimney sections	8HS-18	8H-SCS18	JSC 8 SA1	8TG 18	8 L18	8T- 9	9214
	8HS-24	8H-SCS12		8TG 12	8 L1	8T- 6	9221/9221SS
	8HS-36	8H-SCS6		8TG 6	8 L8	8T- 3	9217/9217SS
Elbows	8HS-015	8H-SEL15	JSC 8 SE	8TG A15	8 E15	8T-EL15	9264
Elbows	8HS-030	8H-SEL30		8TG A30	8 E30	8T-EL30	9266
	8HS-030	8H-SEL30		8TG A30	8 E30	8T-EL30	9266
	8HS-AIS	8H-AJS	JSC 8 AIS	8TG IS	8 RSA	8T-AIS	9244
	8HS-FSA	8H-RJS	JSC 8 FRS	8TG RSH		8T-JS	9946
Firestops/shields		8H-FJS	JSC 8 FAIS	8TG FSA		8T-WS	9980A
Firestops/shields		8H-WS				8T-TCS	9980B
		8H-WS				8T-TCS	9980B
							9980C
Storm collar	8SC	8H-CSC	JSC 8 ASC	8TG SC	8 FC	8T-SC	9959
	8HS-RES	8H-CRCA	JSC 8 DRC	8TG C	8 CPR	8T-CT	9284
Caps			JSC 8 RC	8TG RC	8 CC
Caps					8 CPE
					8 CPE

Wall band	8HS-SBA	8H-CGR	JSC 8 WB	8TG WB	8BM	8T-WB	9268/9268SS
	8F	8H-CFF	JSC 8 ATC	8TG F	8F	8T-TF	9251
	8FT	8H-CFLC	JSC 8 AAF	8TG 15	8FPA	8T-AF6	9249
		8H-CFM	JSC 8 AF2	8TG F24	8FPB	8T-AF12	9250
Flashings		8H-CFH	JSC 8 AF3	8TG FT	8FA	8T-AF24	9281
		8H-CFS			8FB	8T-AF36	9252
					8FBB
Supports	8HS-CSA	8H-SSL9	JSC 8 DCS	8TG RS	8ST	8T-RSP	9262*
Supports	8HS-RSA	8H-SRL9		8TG SB	8S	8T-FSP	9260*
	8HS-RSA	8H-SRL9		8TG SB	8S	8T-FSP	9260*
							*Can only
							accept
							chimney
							above it, not
							below.

2000941

41

Image 41

Contents WinterWarm Introduction Table of ContentsWinterWarm SpeciﬁcationsYour WinterWarm’s Controls What They Do Section I OperationPrimary Air Control DamperBurn Only High-Quality Wood Use the Air Control Settings That Work Best for YouFans WinterWarm Control Settings How To Build a Wood Fire Keep It GoingHigh-Efﬁciency Wood Burning With Catalytic Combustion Starting and Maintaining a Wood FireReloading and Reviving a Wood Fire Remove and Store Ash Safely Special Tactics for Cold-Climate HeatingOpen-Fire Viewing With the Screen Cassette Cleaning the Glass Section II MaintenanceCare of the Cast Iron Surface Care of the Porcelain Enamel SurfaceReplaceable WinterWarm Fiberglass Gaskets Adjust the Door Latch PeriodicallyHow to Replace Gaskets Replacing the Damper Gasket Replacing the Door GasketsReplace Damaged Door Glass Immediately Permanent WinterWarm GasketsTry the Fine Adjustment First Adjust the Damper as NeededUse the Coarse Adjustment Only If Necessary Care of the Catalytic CombustorInspection and Removal of the Combustor When to Suspect a Combustor ProblemLearn to Recognize and Avoid Creosote Clean Chimney System is Safer and Works BetterWatch for Better Results Yearly Spring Cleaning WinterWarm Maintenance ScheduleFireplace Daily Two WeeksPH4 Large WinterWarm Wiring DiagramSection III Preparing a Masonry Chimney Minimum Fireplace DimensionsRequirements for Existing Masonry Fireplace Requirements of your Existing Masonry ChimneyFireplace Maximums Clearance RequirementsHearth Requirements Sealing Requirements Chimney ConnectorFlex Connector System Custom Damper Seal Install the Flex ConnectorRelined Chimney Remove the Masonry Fireplace DamperReverse the Flue Collar If Necessary Install the Floor ProtectorStructural Considerations Installation Chase Dimensions Section IV Installing the Fireplace System CabinetCarefully Observe Local Building Codes Selecting a Location for Your FireplaceChimney Requirements Duct and Vent Placementﬂoor protector must satisfy these requirements Guidelines for an Outside Air SupplyImportant Reminders Flush with the Floor or Laid Over It?Choosing a Facing Material Electrical RequirementsCustomizing the Finished Appearance Use the Right Adhesives Prepare and Install WinterWarm Cabinet 40³⁄ ₈ 1026mm Install the optional cabinet convection blower kit Install the elevated base. Slide the base intoCabinet convection blower in place behind Prepare and Install WinterWarm Firechamber Section V Completing the WinterWarm InstallationConnect the Outside Air Duct to the Air Box Fireplace System onlyPrepare and Install the WinterWarm Front Attach the Rheostat Rod Linkages Connect the WiringInstall the Air Divider Install and Adjust the ControlsInstall the Mantel Install the Latticework PanelsFireplace Systems only Install the Plinth Move the Entire Unit the ﬁnal few inches into the CabinetWinterWarm Large Insert WinterWarm Large Insert Classic Sand Midnight Shell Enamel Parts WinterWarm Large Insert ModelAppendixApproved Chimney Components Appendix Catalytic Combustor Warranty CFM Corporation