Vermont Casting 2100 installation instructions Speciﬁcations, WinterWarm

Page 3

WinterWarm Fireplace Insert or System

Speciﬁcations

WinterWarm

Range of heat output*	10,300 - 30,000 BTU/hr
Maximum heat output**	50,000 BTU/hr
Area heated***	Up to 1500 sq. ft. (140sq. m)
Size of wood splits	20-24” (508-610 mm)
Fuel Capacity	40lbs. (18 kg)
Loading	Front
Flue size	8” (203 mm)
Fireplace Insert weight	475lbs. (216 kg)
Fireplace System weight	840lbs. (380 kg)
Primary Air Control	Manual/thermostatic
Secondary Air Control	Self-regulating
Glass panel	High-temperature ceramic
Flue exit position	Top
Blower rating	106cfm. (115V, 60Hz)

*Under speciﬁc test conditions used during EPA emis- sions standard testing.

**This value can vary depending on how the unit is operated, and the type and moisture content of the fuel used. Figure shown is based on maximum fuel con- sumption obtained under laboratory conditions and on average efﬁciencies.

***These values are based on operation in building- code conforming homes under typical winter climate conditions in New England. If your home is of nonstan- dard construction (e.g. unusually well insulated, not in- sulated, built under ground, etc.) or if you live in a more severe or more temperate climate, these ﬁgures may not apply. Since so many variables affect performance, consult your Vermont Castings’ Authorized Dealer to determine realistic expectations for your home.

6��"

(172 mm)

7��"

(200 mm)

	21��"		37��"
	(553 mm)		(959 mm)
	4��"			8" (203 mm)
	(121 mm)			26��"
				26��"
				(676 mm
	33” (838 mm)	15��"	12��"	12��"
	33” (838 mm)	15��"	(327 mm)	(327 mm)
		(394 mm)	(327 mm)	(327 mm)
		(394 mm)
	7��" (191 mm)
	36"		Top View / System Cabinet
	(914 mm)		Top View / System Cabinet
	41"
	(1041 mm)
			13��"
			(349 mm)
	29��"			7��"
	29��"			(200 mm)
	(759 mm)			(200 mm)
	(759 mm)
				23��"
				(603 mm)
				15��"
				(403 mm)
	25��"		18��" (470 mm)
	(648 mm)

Fig. 1 WinterWarm dimensions.

2000941

3

Image 3

Contents WinterWarm Introduction Table of ContentsWinterWarm SpeciﬁcationsDamper Section I OperationYour WinterWarm’s Controls What They Do Primary Air ControlUse the Air Control Settings That Work Best for You FansBurn Only High-Quality Wood Starting and Maintaining a Wood Fire How To Build a Wood Fire Keep It GoingWinterWarm Control Settings High-Efﬁciency Wood Burning With Catalytic CombustionReloading and Reviving a Wood Fire Special Tactics for Cold-Climate Heating Open-Fire Viewing With the Screen CassetteRemove and Store Ash Safely Care of the Porcelain Enamel Surface Section II MaintenanceCleaning the Glass Care of the Cast Iron SurfaceAdjust the Door Latch Periodically How to Replace GasketsReplaceable WinterWarm Fiberglass Gaskets Permanent WinterWarm Gaskets Replacing the Door GasketsReplacing the Damper Gasket Replace Damaged Door Glass ImmediatelyCare of the Catalytic Combustor Adjust the Damper as NeededTry the Fine Adjustment First Use the Coarse Adjustment Only If NecessaryInspection and Removal of the Combustor When to Suspect a Combustor ProblemClean Chimney System is Safer and Works Better Watch for Better ResultsLearn to Recognize and Avoid Creosote Two Weeks WinterWarm Maintenance ScheduleYearly Spring Cleaning Fireplace DailyPH4 Large WinterWarm Wiring DiagramRequirements of your Existing Masonry Chimney Minimum Fireplace DimensionsSection III Preparing a Masonry Chimney Requirements for Existing Masonry FireplaceClearance Requirements Hearth RequirementsFireplace Maximums Chimney Connector Flex Connector SystemSealing Requirements Remove the Masonry Fireplace Damper Install the Flex ConnectorCustom Damper Seal Relined ChimneyReverse the Flue Collar If Necessary Install the Floor ProtectorSelecting a Location for Your Fireplace Section IV Installing the Fireplace System CabinetStructural Considerations Installation Chase Dimensions Carefully Observe Local Building CodesChimney Requirements Duct and Vent Placementﬂoor protector must satisfy these requirements Guidelines for an Outside Air SupplyImportant Reminders Flush with the Floor or Laid Over It?Electrical Requirements Customizing the Finished AppearanceChoosing a Facing Material Use the Right Adhesives Prepare and Install WinterWarm Cabinet 40³⁄ ₈ 1026mm Install the optional cabinet convection blower kit Install the elevated base. Slide the base intoCabinet convection blower in place behind Prepare and Install WinterWarm Firechamber Section V Completing the WinterWarm InstallationConnect the Outside Air Duct to the Air Box Fireplace System onlyPrepare and Install the WinterWarm Front Attach the Rheostat Rod Linkages Connect the WiringInstall the Air Divider Install and Adjust the ControlsMove the Entire Unit the ﬁnal few inches into the Cabinet Install the Latticework PanelsInstall the Mantel Fireplace Systems only Install the PlinthWinterWarm Large Insert WinterWarm Large Insert Classic Sand Midnight Shell Enamel Parts WinterWarm Large Insert ModelAppendixApproved Chimney Components Appendix Catalytic Combustor Warranty CFM Corporation