Regency U32-NG4, U32-LP4 installation manual Regency Faceplate Trim Installation, Rear burner

Page 11

INSTALLATION

 

 

A)02-43

45

F)02-48

B)02-

 

 

 

Side View

 

 

Bracket

Front edge of

 

 

rear burner

The bottom right edge of Log F)02-48 must sit snugly against the bracket and the front edge of the rear burner.

9)Place Front Left Log G)02-44 onto the 2 front pins as shown.

G)02-44

10)Place the embers and Rockwool on the exposed front burner tray.

11)Test fi re to ensure proper light off (make sure fl ame fl ows smoothly from one end of burner to the other. If there is any fl ame hesitation, check that area for any blockage of the burner port.

12)Install fl ush glass and optional bay glass as per instructions in this manual.

 

 

 

F)02-

A)02-43

 

 

 

48

 

-46

 

47

 

 

 

 

-

 

 

D)02

C)02-56

E)02

 

B)02-45

G)02-44

 

 

 

REGENCY FACEPLATE

&TRIM

INSTALLATION

1)Lay the faceplate panels fl at, face down on something soft so they don't scratch.

2)Take the top faceplate and align the holes in it with the holes in the side panels. Using the screws provided, attach from the top of the panel (the holes in the top panel are slightly larger than the holes in the side panel

Rear View: Faceplate Assembly

Diagram 1

to facilitate easier installation). Diagram 1.

Hint: Don't tighten the screws down completely at this point, continue on with steps 3 and 4 and do a trial fi t to the unit. Make any necessary adjustments and when it fi ts properly then tighten down the screws.

Hearth Trim Option: Hearth Trim is an option that can be used to fi nish off the installation when the bottom of the fi replace is higher than the hearth or to raise the

fi replace. Attach the Hearth Trim to the bottom of the faceplate side panels with the screws provided. See Diagram 1.

3)Using the connectors provided, join the left side trim (with the ON/OFF switch) to the top trim. Diagram 2. Connect the right side trim to the top trim.

4)Place the trim on the assembled faceplate panels, aligning the wire connections from

Rear View: Trim Assembly

Diagram 2

the switches with the notch on the left side panel.

5)Connect the fan switch wires by taking the black and red wires with the male ends (in the grey harness) and connect them with the wire connectors from the fan speed control.

6)Connect the ON/OFF switch wires by taking the black and red wires with the female ends and connect them to the ON/OFF switch.

7)Tuck the wires into the faceplate to keep them away from the insert using the clip provided. Attach the clip to the rear of the faceplate to ensure that the wires do not touch the side

Diagram 3

of the unit. Diagram 3.

8)The power cord should be run behind the faceplate panel.

9)Attachthebrasstrimtothefaceplatebydrilling a1/8"holethroughintothefaceplateusingthe hole in the trim as a guide. Fasten the trim to the faceplate panels using the plated screws. Diagram 4.

10)Attach the faceplate panels to the insert body using the 4 remaining black screws.

U32-4 FPI Direct Vent Gas Insert

11

Image 11
Contents U32 Gas Insert To the NEW Owner FPI GAS InsertTable of Contents Safety Label MA Code CO Detector RequirementsInstallation Materials Required Installation ChecklistMinimum Fireplace Dimensions Manufactured Mobile Home Additional RequirementsGAS Connection Flue Liner InstallationVenting Natural Gas Propane GAS Pipe Pressure TestingGAS Insert Aeration System Optional Brick PanelGas log kit contains the following LOG SET InstallationRear burner Regency Faceplate Trim InstallationFlush Louvers Optional Double Screen DoorsStandard Flush Door Optional Flush TrimRemoving Bay Door BAY LouversOptional BAY Door Optional BAY TrimFor P36D-1 / P36-4 Only Conversion KIT #514-969 from NG to LPInstallation of the DC Sparker Ground Wire from Kit Full Screen Doors Hinge Ensure that Top and sides are Aligned Hampton Cast Faceplate InstallationU31 only Hampton Cast Grill InstallationLeft Side Kensington Front InstallationGlass Door Sub-Frame Hook Kensington Panel Door InstallationOptional Wall Thermostat Optional Remote ControlThermostat Wire Table KensingtonElectrical Grounding Instructions Wiring DiagramsFor Propane Units and Units Equipped with DC Spark Boxes Operating Instructions Copy of Lighting Instruction Plate Maintenance InstructionsMaintenance Bay Glass Removal FAN MaintenanceShut off the gas supply Valve ReplacementEntrire assembly out Install a new gasket and reinstall the valve assemblyMain Assembly Parts ListBurner Assembly & LOG SET Flush Door Bay Door402-918 Complete Faceplate Set Faceplate Assembly400-917 187 189 188 194 203 201 207 195 205 Hampton Cast Faceplate AssemblyU32-4 FPI Direct Vent Gas Insert U32-4 FPI Direct Vent Gas Insert U32-4 FPI Direct Vent Gas Insert Warranty Limited Lifetime WarrantyInstaller Please complete the following information