Bacharach H25-IR manual Parts and Service, Replacement Parts

Page 53

H25-IR	Parts & Service

6 Parts and Service

6.1 Replacement Parts

Item Description	Part Number
Complete Instrument	Refer to Section 1.3
	Ordering Information
H25-IR Unit:
CFC, HCFC, HFC & Halogen gases	3015-4348
R600a	3015-4464
SF6	3015-4477
CO2	3015-4473
R227	3015-4466
Standard Probe Assembly:
6 ft (1.8 m) hose	3015-4635
12 ft (3.7 m) hose	3015-4636
Standard Probe w/ pushbutton and LED Assembly:
6 ft (1.8 m) hose	3015-4639
12 ft (3.7 m) hose	3015-4640
Smart Probe w/ pushbuttons and LCD Assembly:
6 ft (1.8 m) hose	19-7113
12 ft (3.7 m) hose	19-7114
Flexible Probe Tube Assembly:
8 in. (203 mm)	3015-4666
15 in. (381 mm)	3015-4633
Filters:
Located in probe tip:
Pack of 10	3015-4515
Pack of 50	3015-4516
Located inside instrument	3015-4415
Probe Tip	3015-4629
O-Ring, Probe Tube	3015-2664
Bezel, Case	3015-4670
AC Power Cord	304-3459
Fuse, 1A	604-2610

Instruction 3015-4342

49

Image 53

Contents Infrared Refrigerant Gas Leak Detector H25-IRRegister Your Warranty by Visiting WarrantyTable of Contents Parts and Service Hazard Symbols Safety PrecautionsAC Power and Grounding IntroductionExplosive Atmosphere CleaningWorking Inside the Instrument Misuse and Modifications to Instrument Case of MalfunctionUnpacking and Initial Checks Ordering InformationFeatures and Capabilities Leak Rate = Flow Rate x Gas Concentration Functional OverviewFront View Names and Functions of ComponentsRear View Interior Standard Probe with LED and Programmable Pushbutton Standard ProbeSmart Probe Smart Probe Keylock Function System Menu Menu SystemConnecting the AC Power Cord Connecting the ProbePreparing for Operation Turning on the InstrumentMain Menu System Setup Menu System SetupGas Type Leak Units4 4-20 mA Loop RelaysReset Defaults Pchk ModeBrightness ClockRange Configuring the Setups FunctionSetup Name Setpoint Feedback ModeSearch Auto Zero CalibrationExternal Relay Connections Typical Relay 1 Wiring4-40 mA Current Loop Connection MA Current Loop ConnectorPreparing for Operation H25-IR Selecting Internal or External Calibration CalibrationInternal Calibration Selection Calibration Data MenuExternal Calibration Selection and Setup Internal Calibration CALExternal Calibration Material Required ProcedureCAL Factor Improving PPM Measurement Accuracy using the CAL Factor Restoring Factory Calibration Adjusting the CAL FactorCalibration H25-IR Power Using the H25-IRInitial Setup OperationRange Selection Setup SelectionSearching for a Leak Volume AdjustmentMeasuring the PPM Level Measuring the Leak RateLog Menu Logging Measured ReadingsWorking with Logged Measurements Clearing the Log What is PCHK? What to Do when a Fault OccursDiagnostics Menu RS-232 CommunicationOperation H25-IR Sensor Data MaintenanceDiagnostics Menu Last Fault IR Emitter Factory MenuPressure Factory Factory MenuLeak Rate Auto GainLeak Gas Leak TempSensor Cal Leak TempcoFirmware Model SelectProbe Type Items Required Flashing MemorySelect Setup Communications Select File Load Flash Image Removing the Top Cover Part ReplacementProbe Tip Filter & O-Ring Replacement Fuse ReplacementInternal Filter Replacement Replacement Parts Parts and ServiceUnited States Service CentersCFCs, HCFCs, HFCs and Halogens SpecificationsSpecifications H25-IR Continuous Appendix a Factory DefaultsAppendix a H25-IR H25-IR Appendix a Headquarters Hunt Valley Circle, New Kensington, PA