Hearth and Home Technologies CD4236MR, CD4842MR, CD4842MIR, CD4842MLR, CD4842MILR SL-2DVP, Adapter

Page 69

B. Vent Components Diagrams (continued)

SLK-SNKD	SLP-CCS-BK
Snorkel	Cathedral Ceiling Sup-
Termination Cap	port Box-Black

DVP-FBHT

Firebrick Termination Cap

(This termination cap requires an SL-2DVP adapter when used with SLP Pipe)

SLP-TRAP1

Horizontal

Termination Cap

SLP-TRAP2

Horizontal

Termination Cap

Figure 16.8 SLP Series Vent Components

SLP-TVHW
Vertical	PVK-80
Termination Cap	Power Vent

SL-2DVP

Adapter

8-1/8 in.				13 in.
(206 mm)				(330 mm)
(206 mm)				(330 mm)

15in.

(381 mm)

SLP-HRC-SS

Effective Length
Effective Length			5-1/2 in.			8-3/8 in.
5-3/4 to 8-3/8 in.			5-1/2 in.			8-3/8 in.
146 to 213 mm			140 mm			213 mm
146 to 213 mm			140 mm			213 mm
			87°		3°

10-1/2 in.

267 mm

10-7/8 in.

276 mm

SLP-HRC-ZC-SS

Heatilator • Caliber Mesh CD Series-SIT Valve • 4040-849 Rev J • 06/08

69

Image 69

Contents Models CD4236MR CD4842MR Installation and OperationDirect Vent Gas Appliance What to do if you smell gasHomeowner Reference Information CongratulationsTable of Contents Installer GuideUser Guide Appliance Setup TroubleshootingReference Materials Limited Lifetime Warranty Gas Appliance Fireplace Limited Lifetime WarrantyListing and Code Approvals Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Clear SpaceLighting Instructions IPI For Your Safety Read Before LightingLighting StandingPilot After Fireplace is Lit Frequently Asked QuestionsMaintenance Tasks-Homeowner Maintenance and ServiceRemote Control Doors, Surrounds, FrontsMaintenance Tasks-Qualiﬁed Service Technician Typical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Select Appliance LocationModel # Clearances Construct the Appliance ChaseMantel and Wall Projections MantelsMantel Legs or Wall Projections Vent Termination Minimum Clearances Termination LocationsMinimum Clearances for Termination Approved Pipe Vent Information and DiagramsVent Table Key Use of ElbowsVent Diagrams Top Vent Horizontal TerminationOne Elbow Two Elbows Two 45 Elbows replacing One 90 ElbowThree Elbows Installed VerticallyNo Elbow Top Vent Vertical Termination12 ft 3.66 m min 60 ft 18.29 m max One 45 Elbow Rear Vent Horizontal TerminationTwo Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max 17 Flat Bafﬂe Install Vertical Termination BafﬂePipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationInstalling Ceiling Firestop Install the Ceiling FirestopInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Convert from Top Vent to Rear Vent Appliance PreparationOuter Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace 20 Proper Positioning, Leveling And Securing Of An Secure and Level the ApplianceAttach Pipe to the Firebox Assembly Install Vent PipeAssemble Pipe Sections DVP Only Assemble Pipe SectionsAssemble Slip Sections Assemble Vent Sections SLP OnlyDisassemble Vent Sections Secure the Vent SectionsInstall Decorative Ceiling Components SLP only Assemble and Install Storm Collar Install Metal Roof FlashingSLP-FS Install RF4-8Install Vertical Termination Cap Install Decorative Wall Components SLP onlyHeat Shield Requirements for Horizontal Termination Interior Install Horizontal Termination CapFuel Conversion Gas InformationGas Pressure Gas ConnectionStanding Pilot Ignition System Wiring Wiring RequirementsIntelliﬁre Ignition System Wiring Optional Accessories RequirementsWSK-MLT-HTL Electrical Service and RepairWall Switch Installation for Fan Optional Junction Box InstallationFinishing Facing MaterialCombustible Appliance Setup Install the Log Assembly Removing Fixed Glass AssemblyReplacing Fixed Glass Assembly Install Clean Face Components Install TrimInstall Hood Install Top Latch CoverAir Shutter Setting Install Bottom Latch CoverInstall Firescreen Assembly Standing Pilot Ignition System TroubleshootingSymptom Possible Cause Corrective Action Intelliﬁre Ignition System Will not ignite. If the pilot Reference Materials Appliance Dimension DiagramDVP Vent Components Vent Components DiagramsBEK DVP-BEK2 DVP-TVHW DVP-TRAP DVP-HRC-SS Effective Adapter SL-2DVPService #22 Log/Grate AssemblyParts CD4842M Series Parts CD4842M Series ServiceOptional Components Model # Description Contact Information