Hearth and Home Technologies CD4842MR, CD4842MIR, CD4842MLR, CD4842MILR, CD4236MLR, CD4236MR Parts

Page 72

72

Service Parts	CD4236M Series

C. Service

Heatilator • Caliber Mesh CD Series-SIT Valve • 4040-849 Rev J • 06/08

Standing Pilot Valve Assembly

9

11

3

8

16
10	15

7

4

5

1

6

2

IPI Valve Assembly

9

3

8

11

10
4	5	12
4		12
	7	15
	7
1	6
	2

14

13

#	Description of Part	Comments	CD4236MR CD4236MLR CD4236MIR CD4236MILR				Qty.
	Valve Assembly		4040-061	4040-062	4040-063	4040-064	1

1	Flex Ball Valve Assembly		302-320A	302-320A	302-320A	302-320A	1

2	Valve		230-0710	230-0720			1

	Variable Valve				750-500	750-501	1
	Variable Valve				750-500	750-501	1

3	Standing Pilot Assembly		4021-330	4021-329			1

	Intermittent Pilot Assembly				4021-324	4021-325	1
	Intermittent Pilot Assembly				4021-324	4021-325	1

4	Valve Bracket		30060	30060	31824	31824	1

5	Bulkhead Insulation		4021-043	4021-043	4021-043	4021-043	1

6	3/8 Flare x 3/8 NPT Elbow		4021-045	4021-045	4021-045	4021-045	1

7	Bulkhead		4031-192	4031-192	4031-192	4031-192	1

8	Shutter Box Bottom		4040-189	4040-189	4040-189	4040-189	1

9	Shutter Box Top		4040-190	4040-190	4040-190	4040-190	1

10	Valve Bracket		4040-193	4040-193	4040-193	4040-193	1

11	Pilot Bracket	Pre July 2008	4047-126	4047-126	4047-126	4047-126	1

		post July 2008			4047-144	4047-144
		post July 2008			4047-144	4047-144

12	Wire Assembly				593-590A	593-590A	1

13	Control Module				593-592	593-592	1

14	3V Adapter Plug				593-593A	593-593A	1

	Threaded Oriﬁce (.104) - NG		4031-158		4031-158		1

15	Threaded Oriﬁce (.065) - LP			4021-062		4021-062	1

16	Push Button Ignitor		291-513	291-513			1

Parts (continued)

Image 72

Contents Installation and Operation Models CD4236MR CD4842MRDirect Vent Gas Appliance What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents Installer GuideUser Guide Appliance Setup TroubleshootingReference Materials Gas Appliance Fireplace Limited Lifetime Warranty Limited Lifetime WarrantyListing and Code Approvals Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Clear SpaceFor Your Safety Read Before Lighting Lighting Instructions IPILighting StandingPilot Frequently Asked Questions After Fireplace is LitMaintenance and Service Maintenance Tasks-HomeownerRemote Control Doors, Surrounds, FrontsMaintenance Tasks-Qualiﬁed Service Technician Getting Started Typical Appliance SystemDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Select Appliance LocationModel # Construct the Appliance Chase ClearancesMantel and Wall Projections MantelsMantel Legs or Wall Projections Termination Locations Vent Termination Minimum ClearancesMinimum Clearances for Termination Vent Information and Diagrams Approved PipeVent Table Key Use of ElbowsVent Diagrams Top Vent Horizontal TerminationOne Elbow Two 45 Elbows replacing One 90 Elbow Two ElbowsInstalled Vertically Three ElbowsTop Vent Vertical Termination No Elbow12 ft 3.66 m min 60 ft 18.29 m max Rear Vent Horizontal Termination One 45 ElbowTwo Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Install Vertical Termination Bafﬂe 17 Flat BafﬂeVent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationInstall the Ceiling Firestop Installing Ceiling FirestopInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Convert from Top Vent to Rear VentOuter Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace Secure and Level the Appliance 20 Proper Positioning, Leveling And Securing Of AnInstall Vent Pipe Attach Pipe to the Firebox AssemblyAssemble Pipe Sections DVP Only Assemble Pipe SectionsAssemble Vent Sections SLP Only Assemble Slip SectionsSecure the Vent Sections Disassemble Vent SectionsInstall Decorative Ceiling Components SLP only Install Metal Roof Flashing Assemble and Install Storm CollarInstall RF4-8 SLP-FSInstall Vertical Termination Cap Install Decorative Wall Components SLP onlyHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap InteriorGas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements Standing Pilot Ignition System WiringIntelliﬁre Ignition System Wiring Optional Accessories RequirementsElectrical Service and Repair WSK-MLT-HTLJunction Box Installation Wall Switch Installation for Fan OptionalFinishing Facing MaterialCombustible Appliance Setup Install the Log Assembly Removing Fixed Glass AssemblyReplacing Fixed Glass Assembly Install Trim Install Clean Face ComponentsInstall Hood Install Top Latch CoverAir Shutter Setting Install Bottom Latch CoverInstall Firescreen Assembly Troubleshooting Standing Pilot Ignition SystemSymptom Possible Cause Corrective Action Intelliﬁre Ignition System Will not ignite. If the pilot Appliance Dimension Diagram Reference MaterialsVent Components Diagrams DVP Vent ComponentsBEK DVP-BEK2 DVP-TVHW DVP-TRAP DVP-HRC-SS Effective SL-2DVP AdapterService #22 Log/Grate AssemblyParts CD4842M Series Parts Service CD4842M SeriesOptional Components Model # Description Contact Information