Hearth and Home Technologies 839-1390 Replace Burner Orifice for Horizontal Vent Configurations

Page 30

Figure 8.4 Install the inner flue collar on rear of appliance, with damper rod pointing up. A dab of high temperature silicone on the gasket will help gasket adhere to the appliance.

Figure 8.5 Install the inner flue cover on top of the appliance, ensuring that the damper rod is in the up position.

Figure 8.7 Install the inner collar and outer flue collar on the rear of the appliance.

Install the rear vent cover plate, supplied iwth the kit, on the back shield.

Reinstall the cast insert piece in the top of the appliance.

NOTE: A grill cover plate is shipped with the appliance. This plate may be placed beneath the top grille. The use of the plate increases blower efficiency and also hides the interior of appliance from view. See next page for installation instruc- tions.

2.Replace Burner Orifice for Horizontal Vent Configurations

Remove front, glass, and logs (if installed).

Damper Adjustment Plate

Outer Cover Plate

Figure 8.6 Install the outer flue cover, with damper adjustment plate attached, to the top of the appliance.

On top of the appliance: Reattach the damper adjustment with screw.

Burner Locator

Figure 8.8 To remove the burner pan locators from the left and right sides of the burner, remove one screw from each side, lift locators up and out.

Page 30

Quadra-Fire · Sapphire · 250-7233H

September 1, 2008

Image 30
Contents What to do if you smell gas Do not Discard this ManualDo Discardnot Welcome to the Quadra-Fire Family Table of Contents 1Listing and Code Approvals Requirements for the Commonwealth of Massachusetts BELOW. Keep Clear of ALL ObstructionsManufacturer Requirements Getting Started Design & Installation ConsiderationsTools will apply to every installation Tools and Supplies NeededSelecting Appliance Location ClearancesTermination Locations 4Vent Termination Minimum ClearancesAlcove Applications Use of Elbows Vent InformationVenting Components Measuring StandardsHow to Use the Vent Graph Venting Guidelines Exception for Rear Vent KIT, Horizontal InstallationType B Rear Installations for Use with Rear Vent Kit Horizontal TerminationType a Up & Out For installations requiring a vertical rise on the exterior 203mm Vertical Termination Direct Vent PipeStep Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Type a Up & Out Installations for Top Vent Configurations Existing Masonry ChimneyCut and bend flashing as needed to fit Sealant adhesive Flex Liner Flex Coupler Sheet Metal Screws Gas Information Fuel ConversionsConverting to LP Gas Propane Natural GAS Gas Pressures PressureGas Connection Check for GAS LeaksStanding Pilot Ignition System Wiring Recommendation for WireConnecting to the Appliance Wire Size Max. LengthON/OFF Top and Rear Vent Conversion Appliance SetupRemove Shipping Materials At the TOP of the appliance, with exceptions notedReplace Burner Orifice for Horizontal Vent Configurations Grille Cover Plate Installation Accessories059 53 DMS 096 41DMS For Both Quartet and Solitaire Fronts Front InstallationFronts are shipped attached to the face Quartet Door AlignmentHearth Legs Installation Positioning the LogsQty Description Glass Door Assembly Installation Blower Installation Mineral WoolBlower from front Page Blower For TOP or Rear Vent Installations Damper AdjustmentShutter Adjustment Make adjustmentOperating Instructions Before Lighting ApplianceControls For Your Safety Read Before Lighting Lighting ApplianceFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionBe Placed in this Opening Maintaining and Servicing Appliance After servicingMaintenance Tasks Inspect Necessary. USE Caution When CLEANING/HANDLING Ceramic BurnerAppliance Dimension Diagram Reference MaterialsVent Components Diagram Mm inner pipe 6-5/8 in mm outer pipeQuadra-Fire · Sapphire · 250-7233H September 1 Vent Components List HHT SL-PTermination Caps & Kits Sapphire Item # DescriptionService Parts cont’d Hinge Assembly Accessories Cast Parts Individual PiecesService and Maintenance Log Date of Service Performed By Description of ServiceWarranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Sapphire Contact InformationDealer Telephone