Hearth and Home Technologies 839-1440, 839-1390, 839-1460, SAPPH-D-CWL Vent Components Diagram

Page 46

B. Vent Components Diagram

			6-3/8 in.
	6-1/2 in.		(162mm)
	6-1/2 in.
	(165mm)
9-1/4 in.
(235mm)				6-1/2 in.
				6-1/2 in.
		6-3/8 in.		(165mm)	9-5/8 in.
		6-3/8 in.			(244mm)
	6-5/8 in.	(162mm)
	(168mm)
SLP45-BK
		6-5/8 in.
		(168mm)		9-5/8 in.
			SLP90M	9-5/8 in.
			SLP90M	(244mm)
17-24 in.			6-1/2 in.
(432-610mm)			(165mm)
	11-3/4 in.
	(298mm)	5-3/4 in.
		5-3/4 in.
		(146mm)
SLP12AM				6-5/8 in.
SLP12AM		SLP12M		(168mm)
		SLP12M	SLP6M
			SLP6M
					47-3/4 in.
					(1213mm)
			35-3/4 in.
			(908mm)
		23-3/4 in.
		(603mm)
	12-17 in.
	(305-432mm)
3-3/4 in.
(95mm)
SLP4M	SLP6AM	SLP24M	SLP36M		SLP48M
	4 in. (102 mm) inner pipe 6-5/8 in. (168 mm) outer pipe
Figure 12.2 SL-D Series Vent Components
Page 46	Quadra-Fire · Sapphire · 250-7233H				September 1, 2008

Image 46

Contents Do not Discard this Manual What to do if you smell gasDo Discardnot Welcome to the Quadra-Fire Family Table of Contents 1Listing and Code Approvals BELOW. Keep Clear of ALL Obstructions Requirements for the Commonwealth of MassachusettsManufacturer Requirements Getting Started Design & Installation ConsiderationsTools will apply to every installation Tools and Supplies NeededSelecting Appliance Location ClearancesTermination Locations 4Vent Termination Minimum ClearancesAlcove Applications Use of Elbows Vent InformationVenting Components Measuring StandardsHow to Use the Vent Graph Venting Guidelines Exception for Rear Vent KIT, Horizontal InstallationHorizontal Termination Type B Rear Installations for Use with Rear Vent KitType a Up & Out For installations requiring a vertical rise on the exterior 203mm Vertical Termination Direct Vent PipeStep Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Type a Up & Out Installations for Top Vent Configurations Existing Masonry ChimneyCut and bend flashing as needed to fit Sealant adhesive Flex Liner Flex Coupler Sheet Metal Screws Fuel Conversions Gas InformationConverting to LP Gas Propane Natural GAS Gas Pressures PressureGas Connection Check for GAS LeaksStanding Pilot Ignition System Wiring Recommendation for WireConnecting to the Appliance Wire Size Max. LengthON/OFF Top and Rear Vent Conversion Appliance SetupRemove Shipping Materials At the TOP of the appliance, with exceptions notedReplace Burner Oriﬁce for Horizontal Vent Conﬁgurations Accessories Grille Cover Plate Installation059 53 DMS 096 41DMS For Both Quartet and Solitaire Fronts Front InstallationFronts are shipped attached to the face Quartet Door AlignmentPositioning the Logs Hearth Legs InstallationQty Description Mineral Wool Glass Door Assembly Installation Blower InstallationBlower from front Page Blower For TOP or Rear Vent Installations Damper AdjustmentShutter Adjustment Make adjustmentBefore Lighting Appliance Operating InstructionsControls For Your Safety Read Before Lighting Lighting ApplianceInitial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionBe Placed in this Opening Maintaining and Servicing Appliance After servicingMaintenance Tasks Inspect Necessary. USE Caution When CLEANING/HANDLING Ceramic BurnerAppliance Dimension Diagram Reference MaterialsMm inner pipe 6-5/8 in mm outer pipe Vent Components DiagramQuadra-Fire · Sapphire · 250-7233H September 1 Vent Components List HHT SL-PTermination Caps & Kits Sapphire Item # DescriptionService Parts cont’d Hinge Assembly Accessories Cast Parts Individual PiecesService and Maintenance Log Date of Service Performed By Description of ServiceWarranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information SapphireDealer Telephone