Hearth and Home Technologies SL-750TRSFHHIPI Vent Components Diagrams, DVP vent components

Page 67

B. Vent Components Diagrams

		Pipe	Effective Length
		Pipe	Inches	Millimeters
			Inches	Millimeters
		DVP4	4	102
		DVP6	6	152	10-1/2 in.
	Effective	DVP12	12	305	(267 mm)	45°
	Height/Length	DVP24	24	610
		DVP24	24	610
		DVP36	36	914	4-7/8 in.
		DVP48	48	1219	4-7/8 in.
		DVP48	48	1219	( 276 mm)
		DVP6A	3 to 6	76 to 152		10-7/8 in.
	DVP Pipe (see chart)	DVP12A	3 to 12	76 to 305		(276 mm)
	DVP Pipe (see chart)	DVP12A	3 to 12	76 to 305	DVP45 (45º Elbow)
		DVP12MI	3 to 12	76 to 305	DVP45 (45º Elbow)
		DVP24MI	3 to 24	76 to 610
						11-3/8 in.
						(289 mm)
	10 in.
	(254 mm)	10 in.		1 in.
		(254 mm)		1 in.
		(254 mm)		(25 mm)
				(25 mm)
						7-3/8 in.
	24 in.					(187 mm)
	24 in.
	(610 mm)	10 in.				1-1/4 in. (32 mm)
		10 in.				1-1/4 in. (32 mm)
	(254 mm)				9-1/4 in.
					9-1/4 in.
					(235 mm)	1/2 in. TYP
					13-1/4 in.	(13 mm)
					13-1/4 in.
					(337 mm)
	DVP-AS (Attic Shield)	DVP-FS (Ceiling Firestop)			DVP90ST (90° Elbow)
					12 in.	1 in.
					(305 mm)	(25 mm)
	10 in.	1- 1/2 in.				8 in.
	10 in.	1- 1/2 in.				(203 mm)
	(254 mm)	(38 mm)		14 in.
				14 in.
	UP			(356 mm)
	UP
	5 in.	12 in.
	(127 mm)	(305 mm)
					6 in.
					(152 mm)
	DVP-HVS (Vent Support)				DVP-WS (Wall Shield Firestop)
	Figure 16.2 DVP vent components
		Heat & Glo • SL-750TRSFHHIPI • 2156-900 Rev. F • 11/08				67

Image 67

Contents HOT Surfaces What to do if you smell gasHot glass will cause burns Homeowner Reference Information CongratulationsXxxxxxxx User Guide Table of ContentsReference Materials Appliance SetupTroubleshooting FinishingCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsOperating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalGAS Valve Lighting Instructions IPIFinal inspection by What to do if YOU Smell GASIssue Solutions Frequently Asked QuestionsAfter Fireplace is Lit Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningLogs Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection VentingEither cobrahead or SIT Typical Appliance System Getting StartedAny such action may cause a ﬁre hazard Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and ComponentsSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseTOP View Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination Locations= Vent Terminal = AIR Supply Inlet = Area Where Terminal is not PermittedUse of Elbows Vent Information and DiagramsApproved Pipe Vent Table KeyIn. Clearance Use of Flex VentMinimum Maximum SL-750TRSFHHIPI Top Vent Horizontal Termination Two ElbowsV1 Minimum H1 Maximum H1 + H2 Maximum V1 + V2 Minimum Top Vent Horizontal Termination Three ElbowsExhaust restrictor Instructions Top Vent Vertical Termination No Elbow = 60 ft. Max .3 mMinimum Maximum + V 2 Minimum Top Vent Vertical Termination Two 90º ElbowsH1+ H2 Maximum V1 + V2 Minimum Top Vent Vertical Termination Three 90º ElbowsV1 Min H1 Max V2 Min H2 Max V3 Min Top Vent Vertical Termination Four 90º ElbowsH1 Maximum V1 Minimum H1 + H2 Maximum Rear Vent Vertical Termination One Elbow Rear Vent Horizontal Termination Three ElbowsH1 Maximum V1 Minimum H2+ H3 H1+ H2+ H3 Maximum H1+ H2 Maximum V1 Minimum Rear Vent Vertical Termination Two ElbowsH1 Maximum V1 Minimum H1 + H2 Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration FramingPipe DVP SLP Install the Ceiling FirestopFlat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Top Vent Appliance PreparationCut the metal retaining band and fold the sides out Rear Vent13 Proper Positioning and Securing of an Appliance Securing and Leveling the ApplianceAssemble Pipe Sections Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Vent Sections DVP Pipe OnlyAssemble Slip Sections Assemble Vent Sections SLP Pipe OnlyDisassemble Vent Sections Secure the Vent SectionsInstall Decorative Ceiling Components SLP only Assemble and Install Storm Collar Install Metal Roof FlashingSLP-FS Install RF4-8Install Decorative Wall Components SLP only Install Vertical Termination CapHeat Shield Requirements for Horizontal Termination Ansi Z223.1 and CAN/CGA-B149 installation codes Install Horizontal Termination Cap DVP and SLP PipeRefer to of this manual Gas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsIntelliﬁre Ignition System Wiring Optional Accessories RequirementsWith battery back-up Electrical Service and RepairWall Switch Installation for Fan Optional Junction Box InstallationFinishing To install the Splatter GuardSplatter Guard To Remove the Splatter Guard To Close the Lower Access Panel14 Wall Projection Acceptable on one side of opening 16 Facing Materials Facing MaterialTemplate DoorsElevated Hearth Systems Appliance Setup Step Install RefractoryStep LOG Notches Install the Log AssemblyNotch Air Shutter Setting Install Trim and/or SurroundSymptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Ues to spark, and main Reference Materials Appliance Dimension DiagramLocation Inches Millimeters DVP vent components Vent Components DiagramsHorizontal Termination Cap DVP-TRAPDVP-TRAPFL RF6M RF12MBEK DVP-BEK2 COOL-ADDDVP-TV SLP-HRC-SS SLP-HRC-ZC-SS Horizontal Termination CAP DVP-HRC-SS DVP-HRC-ZC-SS Horizontal Termination CAPDVP-TB1 Roof Flashing Ceiling Firestop ElbowExtended Heat Shield RF4-8Wall Thimble-Black Snorkel Black Support Box-BlackAdapter Service Parts Log Set AssemblyAt Depot Service Parts ListIPI Valve Assembly Contact Information