Sears 385. 1884180 owner manual Sliding Buttonhole Foot, Use this, Zipper Edges, Guide, See

Page 14

o PresserFoot Types (Continued)

Sliding Buttonhole Foot

% Sliding buttonhole foot

J

Use this	foot	for buttonholes		of buift-ln
system.	It	is marked	to	measure	your
buttonhofes	accurately.

Uses: Buttonhole making {see page 45).

Zipper Foot

Satin Stitch Foot

E: Zipper foot

F: Satin stitch foot

This

foot can

be

set to sew on each side of

Use this

transparent

foot for satin

stitch and

your

zipper.

The

edges of

the foot

guide the

outJining

applique.

zipper and keep the seam straight.

Uses: Satin

stitch

{see page 36),

Uses:

Zipper

application

(see page

52).

Applique

{see page

37),

Monogramming

(see page

3_88),

Shell

stitching

(see page 5__44),

Geometric

decorative

stitching

(see

page 60).

12

Image 14

Contents Sewing Machine Sears Canada NC Kenmore Sewing MachineTable of Contents Know Your Machine Portable Case or Cabinet is AvailablePage Bobbin Plug in the Machine and Switch on the Power OFFPressure Dial should Reset at Machine is running= Thread Cutter = Setting Spool Pins= Adjust the Presser Foot Lever Foot= Free-Arm Sewing the Removable Extension Table To removeOranycirculargarmentarea Orareasofwearinchildrensclothes Etc To Attach Changethe Presser FootZigzag Foot To Snap OnPresserFoot Types Zipper Edges Sliding Buttonhole FootUse this GuideQu liter Topstitching = Presser Foot TypesButtonhole Foot FabNcs Check Your NeedleTo Change Your Needle Onto = To Remove the Bobbin from the Machine = Wind the BobbinPut Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Pick Up Your Bobbin Thread Toward InchesAdjust the Top Thread Tension TopIs set Indicator panelTop tension Too Tight Too Loose Is upStremh Stitch Position = Three Needle PositionWidth Needle positionThree Needle Position Sem On p Check ChartII1 III Refer to 52 ~3N6 Stitch ShellOn p.15 Onp Stitch Refer toOn p 155 ZoneCheck Turn a Square Corner Control 0 grog Use the Darning PlateUse the darning plate in the following ways Thread tensionCenter Out Control orangeControl 2 to Plate and replace foot holder and foot When you finish darning, remove the darningHeresHow Basle Zigzag Set the Machine Contro I toContro 3 to Very short Applique= Bar Tacking Pressure dial2Embroidery Zigzag foot Darning plate Sew a Button=dth control = Rick-Rack Stretch Stitch length ControlThree-Step Zigzag Stitch width control 5 toSat the Machine Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Zi£rzegfootWeight Set the Machine Stitch width Control LightIlili!!ii!iiilji Cuffs = Learningto Sew ButtonholesHave Or where31controt Stitch wdthControl 3 to Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Control 3 to 8Stitch Iength control orange zone Set the Machine Stitch widthLingerie Smocking Control 3 to 6 2Zigzag foot Stlchwidth control 3 to Zigzag tootIii¸!iiiiii¸...........i Positron Stitch width control 3 toStitch length controt Contro green Satin stitchWhatto do when Improper IncorrectInsert Vacuum Cover plate byDriver Parts List 813404013 B868102403202 655t1920 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable Buttonhole Making 4551 Opener Template 6566Two-point Box Zipper Application 5253 Foot T2, 26 6566Settingupyourmachine Stitch SelectorPage Practical Stitch Chart FAGOT,NGWarranty YearVisit Sewing Machine385