Sears 385. 1884180 owner manual Vacuum, Cover plate by

Page 65

Bulb

1.Unplug the machine and open the face cover.

CAUTION_ The _ight butb will be

HOT, Protect your

fingers when you handle it,

2.Push the bulb up and turn the

bulb counter-clockwise to remove it,

3.Put the new bulb in by pushing it up and turning it clockwise.

To insure that your machrne operates at its best, you need to keep the essential parts clean at all times.

The bobbin area can attract dust and lint. Your machine can become sluggish or knock loudly if a thread is caught,

Follow these directfons:	4.	Brush	or	vacuum	the dust and lint	6,	Slide on	the bobbin	cover plate by
1_ Turn off the power or uoplugthe		out of	the	bobbin	holder,		pushing	it into the	grooves,
1_ Turn off the power or uoplugthe
machine.	5.	Replace	the bobbin.

2.Remove the bobbin cover plate bv firmly pulling it toward you.

3, Remove the bobbin.

63

Image 65

Contents Sewing Machine Kenmore Sewing Machine Sears Canada NCTable of Contents Portable Case or Cabinet is Available Know Your MachinePage Bobbin OFF Plug in the Machine and Switch on the PowerMachine is running Pressure Dial should Reset at= Adjust the Presser Foot Lever = Setting Spool Pins= Thread Cutter FootTo remove = Free-Arm Sewing the Removable Extension TableOranycirculargarmentarea Orareasofwearinchildrensclothes Etc Changethe Presser Foot To AttachZigzag Foot To Snap OnPresserFoot Types Use this Sliding Buttonhole FootZipper Edges GuideQu liter Buttonhole Foot = Presser Foot TypesTopstitching FabNcs Check Your NeedleTo Change Your Needle Put = To Remove the Bobbin from the Machine = Wind the BobbinOnto Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Toward Inches Pick Up Your Bobbin ThreadTop Adjust the Top Thread TensionTop tension Too Tight Too Loose Indicator panelIs set Is upStremh Stitch Width = Three Needle PositionPosition Needle positionThree Needle Position Sem II1 III Check ChartOn p Refer to 52 ~Stitch Shell 3N6On p.15 Stitch Refer to OnpOn p 155 ZoneCheck Turn a Square Corner Use the darning plate in the following ways Use the Darning PlateControl 0 grog Thread tensionCenter Out Control orangeControl 2 to Plate and replace foot holder and foot When you finish darning, remove the darningHeresHow Contro I to Basle Zigzag Set the MachineContro 3 to = Bar Tacking AppliqueVery short Pressure dial2Embroidery Zigzag foot Darning plate Sew a Button=dth control Stitch length Control = Rick-Rack StretchStitch width control 5 to Three-Step ZigzagSarging or Pine Leaf Stretch Stitchin Overcast Stretch StitchingSat the Machine Zi£rzegfootSet the Machine Stitch width Control Light WeightIlili!!ii!iiilji Have = Learningto Sew ButtonholesCuffs Or whereControl 3 to Stitch wdth31controt Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Control 3 to 8Stitch Iength control orange zone Set the Machine Stitch widthLingerie Control 3 to 6 2 SmockingZigzag foot Zigzag toot Stlchwidth control 3 toIii¸!iiiiii¸...........i Positron Stitch width control 3 toStitch length controt Satin stitch Contro greenWhatto do when Improper IncorrectInsert Cover plate by VacuumDriver Parts List 102403202 B868813404013 655tPlug connector Portable Overedge foot 13, 27, 40, 42 Parts list 6566 Performance1920 Buttonhole Making 4551 Opener Template 6566Zipper Application 5253 Foot T2, 26 6566 Two-point BoxStitch Selector SettingupyourmachinePage FAGOT,NG Practical Stitch ChartYear WarrantyVisit Sewing Machine385