Sears 385. 1884180 owner manual Marked buttonhole

Page 53

Marked buttonhole

Cerl[er

marking"

Fabric

Measurement markings

4. ab Mark your buttonhole position carefully on the garment.

b.Placing your garment behind the machine, insert it between the guide

plate and the buttonhole foot as shown.

C_ Align marked buttonhole with center marking on buttonhole foot.

d.Line up your fabric edge with the measurement markings on the guide

plate just in front of the buttonhole foot as shown,

eL Pierce the fabric with the needle at the beginmng of the buttonhole.

NOTE:	tf	you	want	your	buttonhole	to	be 1/2 inch from the garment	edge,
	line	up	the	fabric	with the 1/2	inch	markings each time you start	to sew
	a buttonhole.

a.Lower the buttonhole foot.

b.Start sewing slowly.

c.Allow the machine to do the work by itself. (Do not try to guide the fabric.)

d.Stop sewing when the needle returns to the position where it begins.

To release the buttonhole base plate, pull the lever toward you and lift the base plate off the machine.

Adjusting the stitch density

You may alter the closeness of the stitches by turning the stitch length control from 4 to 3.

fabrics

(_ Fine stitches for figh_

Stitch length control 4 "_o3

0 _'4	-o-
Stretch	Stitch
L	J

51

Image 53

Contents Sewing Machine Kenmore Sewing Machine Sears Canada NCTable of Contents Portable Case or Cabinet is Available Know Your MachinePage Bobbin OFF Plug in the Machine and Switch on the PowerMachine is running Pressure Dial should Reset at= Adjust the Presser Foot Lever = Setting Spool Pins= Thread Cutter FootTo remove = Free-Arm Sewing the Removable Extension TableOranycirculargarmentarea Orareasofwearinchildrensclothes Etc Changethe Presser Foot To AttachZigzag Foot To Snap OnPresserFoot Types Use this Sliding Buttonhole FootZipper Edges GuideQu liter Buttonhole Foot = Presser Foot TypesTopstitching FabNcs Check Your NeedleTo Change Your Needle Put = To Remove the Bobbin from the Machine = Wind the BobbinOnto Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Toward Inches Pick Up Your Bobbin ThreadTop Adjust the Top Thread TensionTop tension Too Tight Too Loose Indicator panelIs set Is upStremh Stitch Width = Three Needle PositionPosition Needle positionThree Needle Position Sem II1 III Check ChartOn p Refer to 52 ~Stitch Shell 3N6On p.15 Stitch Refer to OnpOn p 155 ZoneCheck Turn a Square Corner Use the darning plate in the following ways Use the Darning PlateControl 0 grog Thread tensionCenter Out Control orangeControl 2 to Plate and replace foot holder and foot When you finish darning, remove the darningHeresHow Contro I to Basle Zigzag Set the MachineContro 3 to = Bar Tacking AppliqueVery short Pressure dial2Embroidery Zigzag foot Darning plate Sew a Button=dth control Stitch length Control = Rick-Rack StretchStitch width control 5 to Three-Step ZigzagSarging or Pine Leaf Stretch Stitchin Overcast Stretch StitchingSat the Machine Zi£rzegfootSet the Machine Stitch width Control Light WeightIlili!!ii!iiilji Have = Learningto Sew ButtonholesCuffs Or whereControl 3 to Stitch wdth31controt Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Control 3 to 8Stitch Iength control orange zone Set the Machine Stitch widthLingerie Control 3 to 6 2 SmockingZigzag foot Zigzag toot Stlchwidth control 3 toIii¸!iiiiii¸...........i Positron Stitch width control 3 toStitch length controt Satin stitch Contro greenWhatto do when Improper IncorrectInsert Cover plate by VacuumDriver Parts List 102403202 B868813404013 655tPlug connector Portable Overedge foot 13, 27, 40, 42 Parts list 6566 Performance1920 Buttonhole Making 4551 Opener Template 6566Zipper Application 5253 Foot T2, 26 6566 Two-point BoxStitch Selector SettingupyourmachinePage FAGOT,NG Practical Stitch ChartYear WarrantyVisit Sewing Machine385